git.openwrt.org Git - openwrt/staging/robimarko.git/blob

   1 From 9f66e1dd82e3186aee95282657512ca2aef1afe0 Mon Sep 17 00:00:00 2001
   2 From: Linus Walleij <linus.walleij@linaro.org>
   3 Date: Wed, 19 Oct 2022 21:34:49 +0200
   4 Subject: [PATCH] ARM: dts: bcm53016: Add devicetree for D-Link DWL-8610AP
   5
   6 This adds a device tree for the BCM53016-based D-Link DWL-8610AP
   7 access point wireless router.
   8
   9 The TRX-format partitions had to be named "firmware" due to
  10 an OpenWrt patch that only accepts parting such nodes if they
  11 are named "firmware".
  12
  13 Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
  14 Link: https://lore.kernel.org/r/20221019193449.3036010-2-linus.walleij@linaro.org
  15 Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
  16 ---
  17  arch/arm/boot/dts/Makefile                    |   1 +
  18  .../boot/dts/bcm53016-dlink-dwl-8610ap.dts    | 131 ++++++++++++++++++
  19  2 files changed, 132 insertions(+)
  20  create mode 100644 arch/arm/boot/dts/bcm53016-dlink-dwl-8610ap.dts
  21
  22 --- a/arch/arm/boot/dts/Makefile
  23 +++ b/arch/arm/boot/dts/Makefile
  24 @@ -140,6 +140,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
  25         bcm47094-netgear-r8500.dtb \
  26         bcm47094-phicomm-k3.dtb \
  27         bcm53015-meraki-mr26.dtb \
  28 +       bcm53016-dlink-dwl-8610ap.dtb \
  29         bcm53016-meraki-mr32.dtb \
  30         bcm94708.dtb \
  31         bcm94709.dtb \
  32 --- /dev/null
  33 +++ b/arch/arm/boot/dts/bcm53016-dlink-dwl-8610ap.dts
  34 @@ -0,0 +1,131 @@
  35 +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
  36 +/dts-v1/;
  37 +
  38 +#include "bcm4709.dtsi"
  39 +#include "bcm5301x-nand-cs0-bch8.dtsi"
  40 +#include <dt-bindings/leds/common.h>
  41 +#include <dt-bindings/input/input.h>
  42 +
  43 +/ {
  44 +       model = "D-Link DWL-8610AP";
  45 +       compatible = "dlink,dwl-8610ap", "brcm,bcm53016", "brcm,bcm4708";
  46 +
  47 +       memory@0 {
  48 +               device_type = "memory";
  49 +               /* 512 MB RAM in 2 x Macronix D9PSH chips */
  50 +               reg = <0x00000000 0x08000000>,
  51 +                     <0x88000000 0x08000000>;
  52 +       };
  53 +
  54 +       leds {
  55 +               compatible = "gpio-leds";
  56 +
  57 +               power {
  58 +                       function = LED_FUNCTION_POWER;
  59 +                       color = <LED_COLOR_ID_GREEN>;
  60 +                       gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
  61 +                       default-state = "on";
  62 +               };
  63 +
  64 +               diag {
  65 +                       /* Actually "diag" unclear what this means */
  66 +                       function = LED_FUNCTION_INDICATOR;
  67 +                       color = <LED_COLOR_ID_RED>;
  68 +                       gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
  69 +                       default-state = "on";
  70 +                       linux,default-trigger = "heartbeat";
  71 +               };
  72 +
  73 +               wlan-2g {
  74 +                       function = LED_FUNCTION_WLAN;
  75 +                       color = <LED_COLOR_ID_GREEN>;
  76 +                       gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
  77 +               };
  78 +
  79 +               wlan-5g {
  80 +                       function = LED_FUNCTION_WLAN;
  81 +                       color = <LED_COLOR_ID_GREEN>;
  82 +                       gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
  83 +               };
  84 +       };
  85 +
  86 +       gpio_keys {
  87 +               compatible = "gpio-keys";
  88 +
  89 +               button-reset {
  90 +                       debounce-interval = <100>;
  91 +                       wakeup-source;
  92 +                       linux,code = <KEY_RESTART>;
  93 +                       label = "reset";
  94 +                       /* This GPIO is actually stored in NVRAM, but it's not gonna change */
  95 +                       gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
  96 +               };
  97 +       };
  98 +
  99 +       /*
 100 +        * Flash memory at 0x1e000000-0x1fffffff
 101 +        * Macronix 32 64KB blocks; total size 2MB, same that can be
 102 +        * found attached to the spi_nor SPI controller.
 103 +        */
 104 +       nvram@1e080000 {
 105 +               compatible = "brcm,nvram";
 106 +               reg = <0x1e080000 0x00020000>;
 107 +
 108 +               et0macaddr: et0macaddr {
 109 +               };
 110 +
 111 +               et1macaddr: et1macaddr {
 112 +               };
 113 +       };
 114 +};
 115 +
 116 +&gmac0 {
 117 +       nvmem-cells = <&et0macaddr>;
 118 +       nvmem-cell-names = "mac-address";
 119 +};
 120 +
 121 +&gmac1 {
 122 +       nvmem-cells = <&et1macaddr>;
 123 +       nvmem-cell-names = "mac-address";
 124 +};
 125 +
 126 +&spi_nor {
 127 +       /* Serial SPI NOR Flash MX 25L1606E */
 128 +       status = "okay";
 129 +};
 130 +
 131 +&nandcs {
 132 +       /*
 133 +        * Spansion S34ML01G100TFI00 128 MB NAND Flash memory
 134 +        *
 135 +        * This ECC is a bit unorthodox but it is what the stock firmware
 136 +        * is using, so to be able to mount the original partitions
 137 +        * this is necessary.
 138 +        */
 139 +       nand-ecc-strength = <5>;
 140 +       partitions {
 141 +               compatible = "fixed-partitions";
 142 +               #address-cells = <1>;
 143 +               #size-cells = <1>;
 144 +
 145 +               /* This is named nflash1.trx in CFE */
 146 +               trx@0 {
 147 +                       label = "firmware";
 148 +                       reg = <0x00000000 0x02800000>;
 149 +                       compatible = "brcm,trx";
 150 +               };
 151 +
 152 +               /* This is named nflash1.trx2 in CFE */
 153 +               trx2@2800000 {
 154 +                       label = "firmware2";
 155 +                       reg = <0x02800000 0x02800000>;
 156 +                       compatible = "brcm,trx";
 157 +               };
 158 +
 159 +               /* This is named nflash1.rwfs in CFE */
 160 +               free@5000000 {
 161 +                       label = "free";
 162 +                       reg = <0x05000000 0x03000000>;
 163 +               };
 164 +       };
 165 +};