#include <media/v4l2-common.h>
#include <sound/ac97_codec.h>
-
#define DRIVER_NAME "em28xx"
static int tuner = -1;
{ -1, -1, -1, -1},
};
-/* Boards - EM2880 MSI DIGIVOX AD and EM2880_BOARD_MSI_DIGIVOX_AD_II */
-
-/* Board - EM2870 Kworld 355u
- Analog - No input analog */
-
/* Board - EM2882 Kworld 315U digital */
static const struct em28xx_reg_seq em2882_kworld_315u_digital[] = {
{EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
{ -1, -1, -1, -1},
};
-/* Evga inDtube
- GPIO0 - Enable digital power (s5h1409) - low to enable
- GPIO1 - Enable analog power (tvp5150/emp202) - low to enable
- GPIO4 - xc3028 reset
- GOP3 - s5h1409 reset
+/*
+ * Evga inDtube
+ * GPIO0 - Enable digital power (s5h1409) - low to enable
+ * GPIO1 - Enable analog power (tvp5150/emp202) - low to enable
+ * GPIO4 - xc3028 reset
+ * GOP3 - s5h1409 reset
*/
static const struct em28xx_reg_seq evga_indtube_analog[] = {
{EM2820_R08_GPIO_CTRL, 0x79, 0xff, 60},
{ -1, -1, -1, -1},
};
-/* PCTV HD Mini (80e) GPIOs
- 0-5: not used
- 6: demod reset, active low
- 7: LED on, active high */
+/*
+ * PCTV HD Mini (80e) GPIOs
+ * 0-5: not used
+ * 6: demod reset, active low
+ * 7: LED on, active high
+ */
static const struct em28xx_reg_seq em2874_pctv_80e_digital[] = {
{EM28XX_R06_I2C_CLK, 0x45, 0xff, 10}, /*400 KHz*/
{EM2874_R80_GPIO_P0_CTRL, 0x00, 0xff, 100},/*Demod reset*/
{ -1, -1, -1, -1},
};
-/* eb1a:2868 Reddo DVB-C USB TV Box
- GPIO4 - CU1216L NIM
- Other GPIOs seems to be don't care. */
+/*
+ * eb1a:2868 Reddo DVB-C USB TV Box
+ * GPIO4 - CU1216L NIM
+ * Other GPIOs seems to be don't care.
+ */
static const struct em28xx_reg_seq reddo_dvb_c_usb_box[] = {
{EM2820_R08_GPIO_CTRL, 0xfe, 0xff, 10},
{EM2820_R08_GPIO_CTRL, 0xde, 0xff, 10},
{ -1, -1, -1, -1},
};
-/* 2013:024f PCTV nanoStick T2 290e
+/*
+ * 2013:024f PCTV nanoStick T2 290e
* GPIO_6 - demod reset
* GPIO_7 - LED
*/
};
#endif
-/* 2013:024f PCTV DVB-S2 Stick 460e
+/*
+ * 2013:024f PCTV DVB-S2 Stick 460e
* GPIO_0 - POWER_ON
* GPIO_1 - BOOST
* GPIO_2 - VUV_LNB (red LED)
};
#endif
-/* 1b80:e425 MaxMedia UB425-TC
+/*
+ * 1b80:e425 MaxMedia UB425-TC
* 1b80:e1cc Delock 61959
* GPIO_6 - demod reset, 0=active
* GPIO_7 - LED, 0=active
{ -1, -1, -1, -1},
};
-/* 2304:0242 PCTV QuatroStick (510e)
+/*
+ * 2304:0242 PCTV QuatroStick (510e)
* GPIO_2: decoder reset, 0=active
* GPIO_4: decoder suspend, 0=active
* GPIO_6: demod reset, 0=active
{ -1, -1, -1, -1},
};
-/* 2013:0251 PCTV QuatroStick nano (520e)
+/*
+ * 2013:0251 PCTV QuatroStick nano (520e)
* GPIO_2: decoder reset, 0=active
* GPIO_4: decoder suspend, 0=active
* GPIO_6: demod reset, 0=active
{ -1, -1, -1, -1},
};
-/* 1ae7:9003/9004 SpeedLink Vicious And Devine Laplace webcam
+/*
+ * 1ae7:9003/9004 SpeedLink Vicious And Devine Laplace webcam
* reg 0x80/0x84:
* GPIO_0: capturing LED, 0=on, 1=off
* GPIO_2: AV mute button, 0=pressed, 1=unpressed
.gpio = default_analog,
} },
},
- /* maybe there's a reason behind it why Terratec sells the Hybrid XS
- as Prodigy XS with a different PID, let's keep it separated for now
- maybe we'll need it lateron */
+ /*
+ * maybe there's a reason behind it why Terratec sells the Hybrid XS
+ * as Prodigy XS with a different PID, let's keep it separated for now
+ * maybe we'll need it later on
+ */
[EM2880_BOARD_TERRATEC_PRODIGY_XS] = {
.name = "Terratec Prodigy XS",
.tuner_type = TUNER_XC2028,
.ir_codes = RC_MAP_KWORLD_315U,
.xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE,
- /* Analog mode - still not ready */
- /*.input = { {
+#if 0
+ /* FIXME: Analog mode - still not ready */
+ .input = { {
.type = EM28XX_VMUX_TELEVISION,
.vmux = SAA7115_COMPOSITE2,
.amux = EM28XX_AMUX_VIDEO,
.amux = EM28XX_AMUX_LINE_IN,
.gpio = em2882_kworld_315u_analog1,
.aout = EM28XX_AOUT_PCM_IN | EM28XX_AOUT_PCM_STEREO,
- } }, */
+ } },
+#endif
},
[EM2880_BOARD_EMPIRE_DUAL_TV] = {
.name = "Empire dual TV",
.gpio = evga_indtube_analog,
} },
},
- /* eb1a:2868 Empia EM2870 + Philips CU1216L NIM (Philips TDA10023 +
- Infineon TUA6034) */
+ /*
+ * eb1a:2868 Empia EM2870 + Philips CU1216L NIM
+ * (Philips TDA10023 + Infineon TUA6034)
+ */
[EM2870_BOARD_REDDO_DVB_C_USB_BOX] = {
.name = "Reddo DVB-C USB TV Box",
.tuner_type = TUNER_ABSENT,
.tuner_gpio = reddo_dvb_c_usb_box,
.has_dvb = 1,
},
- /* 1b80:a340 - Empia EM2870, NXP TDA18271HD and LG DT3304, sold
+ /*
+ * 1b80:a340 - Empia EM2870, NXP TDA18271HD and LG DT3304, sold
* initially as the KWorld PlusTV 340U, then as the UB435-Q.
- * Early variants have a TDA18271HD/C1, later ones a TDA18271HD/C2 */
+ * Early variants have a TDA18271HD/C1, later ones a TDA18271HD/C2
+ */
[EM2870_BOARD_KWORLD_A340] = {
.name = "KWorld PlusTV 340U or UB435-Q (ATSC)",
.tuner_type = TUNER_ABSENT, /* Digital-only TDA18271HD */
.dvb_gpio = kworld_a340_digital,
.tuner_gpio = default_tuner_gpio,
},
- /* 2013:024f PCTV nanoStick T2 290e.
- * Empia EM28174, Sony CXD2820R and NXP TDA18271HD/C2 */
+ /*
+ * 2013:024f PCTV nanoStick T2 290e.
+ * Empia EM28174, Sony CXD2820R and NXP TDA18271HD/C2
+ */
[EM28174_BOARD_PCTV_290E] = {
.name = "PCTV nanoStick T2 290e",
.def_i2c_bus = 1,
- .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE | EM28XX_I2C_FREQ_100_KHZ,
+ .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
+ EM28XX_I2C_FREQ_100_KHZ,
.tuner_type = TUNER_ABSENT,
.tuner_gpio = pctv_290e,
.has_dvb = 1,
.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
},
- /* 2013:024f PCTV DVB-S2 Stick 460e
- * Empia EM28174, NXP TDA10071, Conexant CX24118A and Allegro A8293 */
+ /*
+ * 2013:024f PCTV DVB-S2 Stick 460e
+ * Empia EM28174, NXP TDA10071, Conexant CX24118A and Allegro A8293
+ */
[EM28174_BOARD_PCTV_460E] = {
.def_i2c_bus = 1,
- .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE | EM28XX_I2C_FREQ_400_KHZ,
+ .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
+ EM28XX_I2C_FREQ_400_KHZ,
.name = "PCTV DVB-S2 Stick (460e)",
.tuner_type = TUNER_ABSENT,
.tuner_gpio = pctv_460e,
.has_dvb = 1,
.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
},
- /* eb1a:5006 Honestech VIDBOX NW03
- * Empia EM2860, Philips SAA7113, Empia EMP202, No Tuner */
+ /*
+ * eb1a:5006 Honestech VIDBOX NW03
+ * Empia EM2860, Philips SAA7113, Empia EMP202, No Tuner
+ */
[EM2860_BOARD_HT_VIDBOX_NW03] = {
.name = "Honestech Vidbox NW03",
.tuner_type = TUNER_ABSENT,
.amux = EM28XX_AMUX_LINE_IN,
}, {
.type = EM28XX_VMUX_SVIDEO,
- .vmux = SAA7115_SVIDEO3, /* S-VIDEO needs confirming */
+ .vmux = SAA7115_SVIDEO3, /* S-VIDEO needs check */
.amux = EM28XX_AMUX_LINE_IN,
} },
},
- /* 1b80:e425 MaxMedia UB425-TC
- * Empia EM2874B + Micronas DRX 3913KA2 + NXP TDA18271HDC2 */
+ /*
+ * 1b80:e425 MaxMedia UB425-TC
+ * Empia EM2874B + Micronas DRX 3913KA2 + NXP TDA18271HDC2
+ */
[EM2874_BOARD_MAXMEDIA_UB425_TC] = {
.name = "MaxMedia UB425-TC",
.tuner_type = TUNER_ABSENT,
.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
EM28XX_I2C_FREQ_400_KHZ,
},
- /* 2304:0242 PCTV QuatroStick (510e)
- * Empia EM2884 + Micronas DRX 3926K + NXP TDA18271HDC2 */
+ /*
+ * 2304:0242 PCTV QuatroStick (510e)
+ * Empia EM2884 + Micronas DRX 3926K + NXP TDA18271HDC2
+ */
[EM2884_BOARD_PCTV_510E] = {
.name = "PCTV QuatroStick (510e)",
.tuner_type = TUNER_ABSENT,
.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
EM28XX_I2C_FREQ_400_KHZ,
},
- /* 2013:0251 PCTV QuatroStick nano (520e)
- * Empia EM2884 + Micronas DRX 3926K + NXP TDA18271HDC2 */
+ /*
+ * 2013:0251 PCTV QuatroStick nano (520e)
+ * Empia EM2884 + Micronas DRX 3926K + NXP TDA18271HDC2
+ */
[EM2884_BOARD_PCTV_520E] = {
.name = "PCTV QuatroStick nano (520e)",
.tuner_type = TUNER_ABSENT,
.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
EM28XX_I2C_FREQ_400_KHZ,
},
- /* 1b80:e1cc Delock 61959
+ /*
+ * 1b80:e1cc Delock 61959
* Empia EM2874B + Micronas DRX 3913KA2 + NXP TDA18271HDC2
- * mostly the same as MaxMedia UB-425-TC but different remote */
+ * mostly the same as MaxMedia UB-425-TC but different remote
+ */
[EM2874_BOARD_DELOCK_61959] = {
.name = "Delock 61959",
.tuner_type = TUNER_ABSENT,
.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
.leds = pctv_80e_leds,
},
- /* 1ae7:9003/9004 SpeedLink Vicious And Devine Laplace webcam
- * Empia EM2765 + OmniVision OV2640 */
+ /*
+ * 1ae7:9003/9004 SpeedLink Vicious And Devine Laplace webcam
+ * Empia EM2765 + OmniVision OV2640
+ */
[EM2765_BOARD_SPEEDLINK_VAD_LAPLACE] = {
.name = "SpeedLink Vicious And Devine Laplace webcam",
.xclk = EM28XX_XCLK_FREQUENCY_24MHZ,
.buttons = speedlink_vad_laplace_buttons,
.leds = speedlink_vad_laplace_leds,
},
- /* 2013:0258 PCTV DVB-S2 Stick (461e)
- * Empia EM28178, Montage M88DS3103, Montage M88TS2022, Allegro A8293 */
+ /*
+ * 2013:0258 PCTV DVB-S2 Stick (461e)
+ * Empia EM28178, Montage M88DS3103, Montage M88TS2022, Allegro A8293
+ */
[EM28178_BOARD_PCTV_461E] = {
.def_i2c_bus = 1,
- .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE | EM28XX_I2C_FREQ_400_KHZ,
+ .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
+ EM28XX_I2C_FREQ_400_KHZ,
.name = "PCTV DVB-S2 Stick (461e)",
.tuner_type = TUNER_ABSENT,
.tuner_gpio = pctv_461e,
.has_dvb = 1,
.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
},
- /* 2013:025f PCTV tripleStick (292e).
- * Empia EM28178, Silicon Labs Si2168, Silicon Labs Si2157 */
+ /*
+ * 2013:025f PCTV tripleStick (292e).
+ * Empia EM28178, Silicon Labs Si2168, Silicon Labs Si2157
+ */
[EM28178_BOARD_PCTV_292E] = {
.name = "PCTV tripleStick (292e)",
.def_i2c_bus = 1,
- .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE | EM28XX_I2C_FREQ_400_KHZ,
+ .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
+ EM28XX_I2C_FREQ_400_KHZ,
.tuner_type = TUNER_ABSENT,
.tuner_gpio = pctv_292e,
.has_dvb = 1,
.amux = EM28XX_AMUX_LINE_IN,
} },
},
- /* eb1a:8179 Terratec Cinergy T2 Stick HD.
- * Empia EM28178, Silicon Labs Si2168, Silicon Labs Si2146 */
+ /*
+ * eb1a:8179 Terratec Cinergy T2 Stick HD.
+ * Empia EM28178, Silicon Labs Si2168, Silicon Labs Si2146
+ */
[EM28178_BOARD_TERRATEC_T2_STICK_HD] = {
.name = "Terratec Cinergy T2 Stick HD",
.def_i2c_bus = 1,
- .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE | EM28XX_I2C_FREQ_400_KHZ,
+ .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
+ EM28XX_I2C_FREQ_400_KHZ,
.tuner_type = TUNER_ABSENT,
.tuner_gpio = terratec_t2_stick_hd,
.has_dvb = 1,
.driver_info = EM2870_BOARD_KWORLD_355U },
{ USB_DEVICE(0xeb1a, 0xe359),
.driver_info = EM2870_BOARD_KWORLD_355U },
- { USB_DEVICE(0x1b80, 0xe302),
- .driver_info = EM2820_BOARD_PINNACLE_DVC_90 }, /* Kaiser Baas Video to DVD maker */
- { USB_DEVICE(0x1b80, 0xe304),
- .driver_info = EM2820_BOARD_PINNACLE_DVC_90 }, /* Kworld DVD Maker 2 */
+ { USB_DEVICE(0x1b80, 0xe302), /* Kaiser Baas Video to DVD maker */
+ .driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
+ { USB_DEVICE(0x1b80, 0xe304), /* Kworld DVD Maker 2 */
+ .driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
{ USB_DEVICE(0x0ccd, 0x0036),
.driver_info = EM2820_BOARD_TERRATEC_CINERGY_250 },
{ USB_DEVICE(0x0ccd, 0x004c),
const struct em28xx_board *board = &em28xx_boards[dev->model];
u8 xclk = board->xclk, i2c_speed = board->i2c_speed;
- /* Those are the default values for the majority of boards
- Use those values if not specified otherwise at boards entry
+ /*
+ * Those are the default values for the majority of boards
+ * Use those values if not specified otherwise at boards entry
*/
if (!xclk)
xclk = EM28XX_XCLK_IR_RC5_MODE |
- EM28XX_XCLK_FREQUENCY_12MHZ;
+ EM28XX_XCLK_FREQUENCY_12MHZ;
em28xx_write_reg(dev, EM28XX_R0F_XCLK, xclk);
-
if (!i2c_speed)
i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
EM28XX_I2C_FREQ_100_KHZ;
dev->def_i2c_bus = dev->board.def_i2c_bus;
}
-/* Wait until AC97_RESET reports the expected value reliably before proceeding.
+/*
+ * Wait until AC97_RESET reports the expected value reliably before proceeding.
* We also check that two unrelated registers accesses don't return the same
* value to avoid premature return.
* This procedure helps ensuring AC97 register accesses are reliable.
return -ETIMEDOUT;
}
-/* Since em28xx_pre_card_setup() requires a proper dev->model,
+/*
+ * Since em28xx_pre_card_setup() requires a proper dev->model,
* this won't work for boards with generic PCI IDs
*/
static void em28xx_pre_card_setup(struct em28xx *dev)
{
- /* Set the initial XCLK and I2C clock values based on the board
- definition */
+ /*
+ * Set the initial XCLK and I2C clock values based on the board
+ * definition
+ */
em28xx_set_xclk_i2c_speed(dev);
/* request some modules */
case EM2861_BOARD_KWORLD_PVRTV_300U:
case EM2880_BOARD_KWORLD_DVB_305U:
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0x6d);
- msleep(10);
+ usleep_range(10000, 11000);
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0x7d);
- msleep(10);
+ usleep_range(10000, 11000);
break;
case EM2870_BOARD_COMPRO_VIDEOMATE:
- /* TODO: someone can do some cleanup here...
- not everything's needed */
+ /*
+ * TODO: someone can do some cleanup here...
+ * not everything's needed
+ */
em28xx_write_reg(dev, EM2880_R04_GPO, 0x00);
- msleep(10);
+ usleep_range(10000, 11000);
em28xx_write_reg(dev, EM2880_R04_GPO, 0x01);
- msleep(10);
+ usleep_range(10000, 11000);
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfd);
mdelay(70);
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfc);
mdelay(70);
break;
case EM2870_BOARD_TERRATEC_XS_MT2060:
- /* this device needs some gpio writes to get the DVB-T
- demod work */
+ /*
+ * this device needs some gpio writes to get the DVB-T
+ * demod work
+ */
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfe);
mdelay(70);
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xde);
mdelay(70);
break;
case EM2870_BOARD_PINNACLE_PCTV_DVB:
- /* this device needs some gpio writes to get the
- DVB-T demod work */
+ /*
+ * this device needs some gpio writes to get the
+ * DVB-T demod work
+ */
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfe);
mdelay(70);
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xde);
case EM2882_BOARD_KWORLD_ATSC_315U:
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xff);
- msleep(10);
+ usleep_range(10000, 11000);
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfe);
- msleep(10);
+ usleep_range(10000, 11000);
em28xx_write_reg(dev, EM2880_R04_GPO, 0x00);
- msleep(10);
+ usleep_range(10000, 11000);
em28xx_write_reg(dev, EM2880_R04_GPO, 0x08);
- msleep(10);
+ usleep_range(10000, 11000);
break;
case EM2860_BOARD_KAIOMY_TVNPC_U2:
em28xx_write_regs(dev, EM28XX_R06_I2C_CLK, "\x40", 1);
em28xx_write_regs(dev, 0x0d, "\x42", 1);
em28xx_write_regs(dev, 0x08, "\xfd", 1);
- msleep(10);
+ usleep_range(10000, 11000);
em28xx_write_regs(dev, 0x08, "\xff", 1);
- msleep(10);
+ usleep_range(10000, 11000);
em28xx_write_regs(dev, 0x08, "\x7f", 1);
- msleep(10);
+ usleep_range(10000, 11000);
em28xx_write_regs(dev, 0x08, "\x6b", 1);
break;
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xff);
msleep(70);
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xf7);
- msleep(10);
+ usleep_range(10000, 11000);
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfe);
msleep(70);
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfd);
break;
case EM2860_BOARD_TERRATEC_GRABBY:
- /* HACK?: Ensure AC97 register reading is reliable before
+ /*
+ * HACK?: Ensure AC97 register reading is reliable before
* proceeding. In practice, this will wait about 1.6 seconds.
*/
em28xx_wait_until_ac97_features_equals(dev, 0x6a90);
return 0;
}
- /* HINT method: EEPROM
+ /*
+ * HINT method: EEPROM
*
* This method works only for boards with eeprom.
* Uses a hash of all eeprom bytes. The hash should be
}
}
- /* HINT method: I2C attached devices
+ /*
+ * HINT method: I2C attached devices
*
* This method works for all boards.
* Uses a hash of i2c scanned devices.
* This solution is only valid if they do not share eeprom
* hash identities which has not been determined as yet.
*/
- if (em28xx_hint_board(dev) < 0)
+ if (em28xx_hint_board(dev) < 0) {
dev_err(&dev->intf->dev, "Board not discovered\n");
- else {
+ } else {
em28xx_set_model(dev);
em28xx_pre_card_setup(dev);
}
}
dev_info(&dev->intf->dev, "Identified as %s (card=%d)\n",
- dev->board.name, dev->model);
+ dev->board.name, dev->model);
dev->tuner_type = em28xx_boards[dev->model].tuner_type;
{
struct tveeprom tv;
- if (dev->eedata == NULL)
+ if (!dev->eedata)
break;
#if defined(CONFIG_MODULES) && defined(MODULE)
request_module("tveeprom");
}
case EM2882_BOARD_KWORLD_ATSC_315U:
em28xx_write_reg(dev, 0x0d, 0x42);
- msleep(10);
+ usleep_range(10000, 11000);
em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfd);
- msleep(10);
+ usleep_range(10000, 11000);
break;
case EM2820_BOARD_KWORLD_PVRTV2800RF:
/* GPIO enables sound on KWORLD PVR TV 2800RF */
if (!em28xx_hint_board(dev))
em28xx_set_model(dev);
- /* In cases where we had to use a board hint, the call to
- em28xx_set_mode() in em28xx_pre_card_setup() was a no-op,
- so make the call now so the analog GPIOs are set properly
- before probing the i2c bus. */
+ /*
+ * In cases where we had to use a board hint, the call to
+ * em28xx_set_mode() in em28xx_pre_card_setup() was a no-op,
+ * so make the call now so the analog GPIOs are set properly
+ * before probing the i2c bus.
+ */
em28xx_gpio_set(dev, dev->board.tuner_gpio);
em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
break;
if (!em28xx_hint_board(dev))
em28xx_set_model(dev);
- /* In cases where we had to use a board hint, the call to
- em28xx_set_mode() in em28xx_pre_card_setup() was a no-op,
- so make the call now so the analog GPIOs are set properly
- before probing the i2c bus. */
+ /*
+ * In cases where we had to use a board hint, the call to
+ * em28xx_set_mode() in em28xx_pre_card_setup() was a no-op,
+ * so make the call now so the analog GPIOs are set properly
+ * before probing the i2c bus.
+ */
em28xx_gpio_set(dev, dev->board.tuner_gpio);
em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
break;
*/
/*
- * Devicdes with an audio-only interface also have a V4L/DVB/RC
- * interface. Don't register extensions twice on those devices.
+ * Devices with an audio-only intf also have a V4L/DVB/RC
+ * intf. Don't register extensions twice on those devices.
*/
if (dev->is_audio_only) {
#if defined(CONFIG_MODULES) && defined(MODULE)
static void em28xx_unregister_media_device(struct em28xx *dev)
{
-
#ifdef CONFIG_MEDIA_CONTROLLER
if (dev->media_dev) {
media_device_unregister(dev->media_dev);
* em28xx_release_resources()
* unregisters the v4l2,i2c and usb devices
* called when the device gets disconnected or at module unload
-*/
+ */
static void em28xx_release_resources(struct em28xx *dev)
{
struct usb_device *udev = interface_to_usbdev(dev->intf);
EM28XX_I2C_ALGO_EM28XX);
if (retval < 0) {
dev_err(&dev->intf->dev,
- "%s: em28xx_i2c_register bus 1 - error [%d]!\n",
- __func__, retval);
+ "%s: em28xx_i2c_register bus 1 - error [%d]!\n",
+ __func__, retval);
em28xx_i2c_unregister(dev, 0);
int nr;
struct em28xx *sec_dev = kzalloc(sizeof(*sec_dev), GFP_KERNEL);
- if (sec_dev == NULL) {
+ if (!sec_dev) {
dev->dev_next = NULL;
return -ENOMEM;
}
if (nr >= EM28XX_MAXBOARDS) {
/* No free device slots */
dev_warn(&dev->intf->dev, ": Supports only %i em28xx boards.\n",
- EM28XX_MAXBOARDS);
+ EM28XX_MAXBOARDS);
kfree(sec_dev);
dev->dev_next = NULL;
return -ENOMEM;
/* allocate memory for our device state and initialize it */
dev = kzalloc(sizeof(*dev), GFP_KERNEL);
- if (dev == NULL) {
+ if (!dev) {
retval = -ENOMEM;
goto err;
}
dev->alt_max_pkt_size_isoc =
kmalloc(sizeof(dev->alt_max_pkt_size_isoc[0]) *
interface->num_altsetting, GFP_KERNEL);
- if (dev->alt_max_pkt_size_isoc == NULL) {
+ if (!dev->alt_max_pkt_size_isoc) {
kfree(dev);
retval = -ENOMEM;
goto err;
for (i = 0; i < interface->num_altsetting; i++) {
int ep;
- for (ep = 0; ep < interface->altsetting[i].desc.bNumEndpoints; ep++) {
+ for (ep = 0;
+ ep < interface->altsetting[i].desc.bNumEndpoints;
+ ep++) {
const struct usb_endpoint_descriptor *e;
int sizedescr, size;
break;
}
}
- /* NOTE:
+ /*
+ * NOTE:
* Old logic with support for isoc transfers only was:
* 0x82 isoc => analog
* 0x83 isoc => audio
if (has_vendor_audio)
dev_err(&interface->dev,
"em28xx: device seems to have vendor AND usb audio class interfaces !\n"
- "\t\tThe vendor interface will be ignored. Please contact the developers <linux-media@vger.kernel.org>\n");
+ "\t\tThe vendor interface will be ignored. Please contact the developers <linux-media@vger.kernel.org>\n");
dev->usb_audio_type = EM28XX_USB_AUDIO_CLASS;
break;
}
dev->num_alt = interface->num_altsetting;
- if ((unsigned)card[nr] < em28xx_bcount)
+ if ((unsigned int)card[nr] < em28xx_bcount)
dev->model = card[nr];
/* save our data pointer in this interface device */
/* allocate device struct and check if the device is a webcam */
mutex_init(&dev->lock);
retval = em28xx_init_dev(dev, udev, interface, nr);
- if (retval) {
+ if (retval)
goto err_free;
- }
if (usb_xfer_mode < 0) {
if (dev->is_webcam)
if (has_video &&
dev->board.decoder == EM28XX_NODECODER &&
dev->em28xx_sensor == EM28XX_NOSENSOR) {
-
dev_err(&interface->dev,
"Currently, V4L2 is not supported on this model\n");
has_video = false;
/* Select USB transfer types to use */
if (has_dvb) {
if (!dev->dvb_ep_isoc_ts2 ||
- (try_bulk && dev->dvb_ep_bulk_ts2))
+ (try_bulk && dev->dvb_ep_bulk_ts2))
dev->dev_next->dvb_xfer_bulk = 1;
dev_info(&dev->intf->dev, "dvb ts2 set to %s mode.\n",
- dev->dev_next->dvb_xfer_bulk ? "bulk" : "isoc");
+ dev->dev_next->dvb_xfer_bulk ? "bulk" : "isoc");
}
dev->dev_next->dvb_ep_isoc = dev->dvb_ep_isoc_ts2;
if (!dev)
return;
- if (dev->dev_next != NULL) {
+ if (dev->dev_next) {
dev->dev_next->disconnected = 1;
dev_info(&dev->intf->dev, "Disconnecting %s\n",
- dev->dev_next->name);
+ dev->dev_next->name);
flush_request_modules(dev->dev_next);
}
em28xx_close_extension(dev);
- if (dev->dev_next != NULL)
+ if (dev->dev_next)
em28xx_release_resources(dev->dev_next);
em28xx_release_resources(dev);
- if (dev->dev_next != NULL) {
+ if (dev->dev_next) {
kref_put(&dev->dev_next->ref, em28xx_free_device);
dev->dev_next = NULL;
}
projects / openwrt / staging / blogic.git / commitdiff