pinctrl: qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant

If you do this on an sdm845 board:
  grep "" /sys/kernel/debug/pinctrl/*spmi:pmic*/pinconf-groups

...it looks like nonsense.  For every pin you see listed:
  input bias disabled, input bias high impedance, input bias pull down, input bias pull up, ...

That's because pmic_gpio_config_get() isn't complying with the rules
that pinconf_generic_dump_one() expects.  Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.

Let's fix this.

From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist.  I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases.  While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.

NOTE: This also fixes an apparent typo for reading
PIN_CONFIG_BIAS_DISABLE where the old driver was accidentally
using "=" instead of "==" and thus was setting some internal
state when you tried to query PIN_CONFIG_BIAS_DISABLE.  Oops.

Fixes: eadff3024472 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
index 3e66e0d1001070c5925512228766c659fd07d2de..cf82db78e69e6f4fe994be61e0f88e2feee61a05 100644 (file)
--- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
@@ -390,31 +390,47 @@ static int pmic_gpio_config_get(struct pinctrl_dev *pctldev,
 
        switch (param) {
        case PIN_CONFIG_DRIVE_PUSH_PULL:
-               arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_CMOS;
+               if (pad->buffer_type != PMIC_GPIO_OUT_BUF_CMOS)
+                       return -EINVAL;
+               arg = 1;
                break;
        case PIN_CONFIG_DRIVE_OPEN_DRAIN:
-               arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS;
+               if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS)
+                       return -EINVAL;
+               arg = 1;
                break;
        case PIN_CONFIG_DRIVE_OPEN_SOURCE:
-               arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS;
+               if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS)
+                       return -EINVAL;
+               arg = 1;
                break;
        case PIN_CONFIG_BIAS_PULL_DOWN:
-               arg = pad->pullup == PMIC_GPIO_PULL_DOWN;
+               if (pad->pullup != PMIC_GPIO_PULL_DOWN)
+                       return -EINVAL;
+               arg = 1;
                break;
        case PIN_CONFIG_BIAS_DISABLE:
-               arg = pad->pullup = PMIC_GPIO_PULL_DISABLE;
+               if (pad->pullup != PMIC_GPIO_PULL_DISABLE)
+                       return -EINVAL;
+               arg = 1;
                break;
        case PIN_CONFIG_BIAS_PULL_UP:
-               arg = pad->pullup == PMIC_GPIO_PULL_UP_30;
+               if (pad->pullup != PMIC_GPIO_PULL_UP_30)
+                       return -EINVAL;
+               arg = 1;
                break;
        case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
-               arg = !pad->is_enabled;
+               if (pad->is_enabled)
+                       return -EINVAL;
+               arg = 1;
                break;
        case PIN_CONFIG_POWER_SOURCE:
                arg = pad->power_source;
                break;
        case PIN_CONFIG_INPUT_ENABLE:
-               arg = pad->input_enabled;
+               if (!pad->input_enabled)
+                       return -EINVAL;
+               arg = 1;
                break;
        case PIN_CONFIG_OUTPUT:
                arg = pad->out_value;