#define MVNETA_GMAC_CTRL_0 0x2c00
#define MVNETA_GMAC_MAX_RX_SIZE_SHIFT 2
#define MVNETA_GMAC_MAX_RX_SIZE_MASK 0x7ffc
+#define MVNETA_GMAC0_PORT_1000BASE_X BIT(1)
#define MVNETA_GMAC0_PORT_ENABLE BIT(0)
#define MVNETA_GMAC_CTRL_2 0x2c08
#define MVNETA_GMAC2_INBAND_AN_ENABLE BIT(0)
#define MVNETA_GMAC_FORCE_LINK_DOWN BIT(0)
#define MVNETA_GMAC_FORCE_LINK_PASS BIT(1)
#define MVNETA_GMAC_INBAND_AN_ENABLE BIT(2)
+#define MVNETA_GMAC_AN_BYPASS_ENABLE BIT(3)
+#define MVNETA_GMAC_INBAND_RESTART_AN BIT(4)
#define MVNETA_GMAC_CONFIG_MII_SPEED BIT(5)
#define MVNETA_GMAC_CONFIG_GMII_SPEED BIT(6)
#define MVNETA_GMAC_AN_SPEED_EN BIT(7)
+#define MVNETA_GMAC_CONFIG_FLOW_CTRL BIT(8)
+#define MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL BIT(9)
#define MVNETA_GMAC_AN_FLOW_CTRL_EN BIT(11)
#define MVNETA_GMAC_CONFIG_FULL_DUPLEX BIT(12)
#define MVNETA_GMAC_AN_DUPLEX_EN BIT(13)
{
__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
- /* We only support QSGMII, SGMII and RGMII modes */
+ /* We only support QSGMII, SGMII, 802.3z and RGMII modes */
if (state->interface != PHY_INTERFACE_MODE_NA &&
state->interface != PHY_INTERFACE_MODE_QSGMII &&
state->interface != PHY_INTERFACE_MODE_SGMII &&
+ !phy_interface_mode_is_8023z(state->interface) &&
!phy_interface_mode_is_rgmii(state->interface)) {
bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
return;
/* Half-duplex at speeds higher than 100Mbit is unsupported */
phylink_set(mask, 1000baseT_Full);
phylink_set(mask, 1000baseX_Full);
- phylink_set(mask, 10baseT_Half);
- phylink_set(mask, 10baseT_Full);
- phylink_set(mask, 100baseT_Half);
- phylink_set(mask, 100baseT_Full);
+
+ if (!phy_interface_mode_is_8023z(state->interface)) {
+ /* 10M and 100M are only supported in non-802.3z mode */
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+ }
bitmap_and(supported, supported, mask,
__ETHTOOL_LINK_MODE_MASK_NBITS);
return 1;
}
+static void mvneta_mac_an_restart(struct net_device *ndev)
+{
+ struct mvneta_port *pp = netdev_priv(ndev);
+ u32 gmac_an = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+
+ mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG,
+ gmac_an | MVNETA_GMAC_INBAND_RESTART_AN);
+ mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG,
+ gmac_an & ~MVNETA_GMAC_INBAND_RESTART_AN);
+}
+
static void mvneta_mac_config(struct net_device *ndev, unsigned int mode,
const struct phylink_link_state *state)
{
struct mvneta_port *pp = netdev_priv(ndev);
+ u32 new_ctrl0, gmac_ctrl0 = mvreg_read(pp, MVNETA_GMAC_CTRL_0);
u32 new_ctrl2, gmac_ctrl2 = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
u32 new_clk, gmac_clk = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
u32 new_an, gmac_an = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+ new_ctrl0 = gmac_ctrl0 & ~MVNETA_GMAC0_PORT_1000BASE_X;
new_ctrl2 = gmac_ctrl2 & ~(MVNETA_GMAC2_INBAND_AN_ENABLE |
MVNETA_GMAC2_PORT_RESET);
new_clk = gmac_clk & ~MVNETA_GMAC_1MS_CLOCK_ENABLE;
MVNETA_GMAC_CONFIG_MII_SPEED |
MVNETA_GMAC_CONFIG_GMII_SPEED |
MVNETA_GMAC_AN_SPEED_EN |
+ MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL |
+ MVNETA_GMAC_CONFIG_FLOW_CTRL |
MVNETA_GMAC_AN_FLOW_CTRL_EN |
MVNETA_GMAC_CONFIG_FULL_DUPLEX |
MVNETA_GMAC_AN_DUPLEX_EN);
new_ctrl2 |= MVNETA_GMAC2_PORT_RGMII;
if (state->interface == PHY_INTERFACE_MODE_QSGMII ||
- state->interface == PHY_INTERFACE_MODE_SGMII)
+ state->interface == PHY_INTERFACE_MODE_SGMII ||
+ phy_interface_mode_is_8023z(state->interface))
new_ctrl2 |= MVNETA_GMAC2_PCS_ENABLE;
if (!phylink_autoneg_inband(mode)) {
new_an |= MVNETA_GMAC_CONFIG_GMII_SPEED;
else if (state->speed == SPEED_100)
new_an |= MVNETA_GMAC_CONFIG_MII_SPEED;
- } else {
+ } else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
/* SGMII mode receives the state from the PHY */
new_ctrl2 |= MVNETA_GMAC2_INBAND_AN_ENABLE;
new_clk |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
MVNETA_GMAC_INBAND_AN_ENABLE |
MVNETA_GMAC_AN_SPEED_EN |
MVNETA_GMAC_AN_DUPLEX_EN;
+ } else {
+ /* 802.3z negotiation - only 1000base-X */
+ new_ctrl0 |= MVNETA_GMAC0_PORT_1000BASE_X;
+ new_clk |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
+ new_an = (new_an & ~(MVNETA_GMAC_FORCE_LINK_DOWN |
+ MVNETA_GMAC_FORCE_LINK_PASS)) |
+ MVNETA_GMAC_INBAND_AN_ENABLE |
+ MVNETA_GMAC_CONFIG_GMII_SPEED |
+ /* The MAC only supports FD mode */
+ MVNETA_GMAC_CONFIG_FULL_DUPLEX;
}
/* Armada 370 documentation says we can only change the port mode
* and in-band enable when the link is down, so force it down
* while making these changes. We also do this for GMAC_CTRL2 */
- if ((new_ctrl2 ^ gmac_ctrl2) & MVNETA_GMAC2_INBAND_AN_ENABLE ||
+ if ((new_ctrl0 ^ gmac_ctrl0) & MVNETA_GMAC0_PORT_1000BASE_X ||
+ (new_ctrl2 ^ gmac_ctrl2) & MVNETA_GMAC2_INBAND_AN_ENABLE ||
(new_an ^ gmac_an) & MVNETA_GMAC_INBAND_AN_ENABLE) {
mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG,
(gmac_an & ~MVNETA_GMAC_FORCE_LINK_PASS) |
MVNETA_GMAC_FORCE_LINK_DOWN);
}
+ if (new_ctrl0 != gmac_ctrl0)
+ mvreg_write(pp, MVNETA_GMAC_CTRL_0, new_ctrl0);
if (new_ctrl2 != gmac_ctrl2)
mvreg_write(pp, MVNETA_GMAC_CTRL_2, new_ctrl2);
if (new_clk != gmac_clk)
static const struct phylink_mac_ops mvneta_phylink_ops = {
.validate = mvneta_validate,
.mac_link_state = mvneta_mac_link_state,
+ .mac_an_restart = mvneta_mac_an_restart,
.mac_config = mvneta_mac_config,
.mac_link_down = mvneta_mac_link_down,
.mac_link_up = mvneta_mac_link_up,
if (phy_mode == PHY_INTERFACE_MODE_QSGMII)
mvreg_write(pp, MVNETA_SERDES_CFG, MVNETA_QSGMII_SERDES_PROTO);
- else if (phy_mode == PHY_INTERFACE_MODE_SGMII)
+ else if (phy_mode == PHY_INTERFACE_MODE_SGMII ||
+ phy_mode == PHY_INTERFACE_MODE_1000BASEX)
mvreg_write(pp, MVNETA_SERDES_CFG, MVNETA_SGMII_SERDES_PROTO);
else if (!phy_interface_mode_is_rgmii(phy_mode))
return -EINVAL;