Staging: bcm: Shortened some lines in select_alternate_setting_for_highspeed_modem()

Signed-off-by: Matthias Beyer <mail@beyermatthias.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/drivers/staging/bcm/InterfaceInit.c b/drivers/staging/bcm/InterfaceInit.c
index 9f9045d569f8015d06b6ac7373e0628a80426b00..276825f0c44ede9caeaa06a6fb32cb71ace35562 100644 (file)
--- a/drivers/staging/bcm/InterfaceInit.c
+++ b/drivers/staging/bcm/InterfaceInit.c
@@ -389,14 +389,12 @@ static int select_alternate_setting_for_highspeed_modem(
                retval = usb_set_interface(psIntfAdapter->udev,
                                           DEFAULT_SETTING_0,
                                           ALTERNATE_SETTING_1);
-       BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT, DRV_ENTRY,
-                       DBG_LVL_ALL,
+       BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT, DRV_ENTRY, DBG_LVL_ALL,
                        "BCM16 is applicable on this dongle\n");
        if (retval || !psIntfAdapter->bHighSpeedDevice) {
                *usedIntOutForBulkTransfer = EP2;
                *endpoint = &iface_desc->endpoint[EP2].desc;
-               BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT,
-                               DRV_ENTRY, DBG_LVL_ALL,
+               BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT, DRV_ENTRY, DBG_LVL_ALL,
                                "Interface altsetting failed or modem is configured to Full Speed, hence will work on default setting 0\n");
                /*
                 * If Modem is high speed device EP2 should be
@@ -409,8 +407,8 @@ static int select_alternate_setting_for_highspeed_modem(
                                        !usb_endpoint_is_int_out(*endpoint)) ||
                                (!psIntfAdapter->bHighSpeedDevice &&
                                 !usb_endpoint_is_bulk_out(*endpoint))) {
-                       BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT,
-                                       DRV_ENTRY, DBG_LVL_ALL,
+                       BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT, DRV_ENTRY,
+                                       DBG_LVL_ALL,
                                        "Configuring the EEPROM\n");
                        /* change the EP2, EP4 to INT OUT end point */
                        ConfigureEndPointTypesThroughEEPROM(
@@ -422,13 +420,10 @@ static int select_alternate_setting_for_highspeed_modem(
                         * will show fail and re-enumerate the
                         * device
                         */
-                       retval = usb_reset_device(
-                                       psIntfAdapter->udev);
+                       retval = usb_reset_device(psIntfAdapter->udev);
                        if (retval) {
-                               BCM_DEBUG_PRINT(psAd,
-                                               DBG_TYPE_INITEXIT,
-                                               DRV_ENTRY,
-                                               DBG_LVL_ALL,
+                               BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT,
+                                               DRV_ENTRY, DBG_LVL_ALL,
                                                "reset failed.  Re-enumerating the device.\n");
                                return retval;
                        }
@@ -438,26 +433,23 @@ static int select_alternate_setting_for_highspeed_modem(
                    usb_endpoint_is_bulk_out(*endpoint)) {
                        /* Once BULK is selected in FS mode. Revert it back to INT. Else USB_IF will fail. */
                        UINT _uiData = ntohl(EP2_CFG_INT);
-                       BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT,
-                                       DRV_ENTRY, DBG_LVL_ALL,
+                       BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT, DRV_ENTRY,
+                                       DBG_LVL_ALL,
                                        "Reverting Bulk to INT as it is in Full Speed mode.\n");
-                       BeceemEEPROMBulkWrite(psAd,
-                                       (PUCHAR) & _uiData,
-                                       0x136, 4, TRUE);
+                       BeceemEEPROMBulkWrite(psAd, (PUCHAR) & _uiData, 0x136,
+                                             4, TRUE);
                }
        } else {
                *usedIntOutForBulkTransfer = EP4;
                *endpoint = &iface_desc->endpoint[EP4].desc;
-               BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT,
-                               DRV_ENTRY, DBG_LVL_ALL,
+               BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT, DRV_ENTRY, DBG_LVL_ALL,
                                "Choosing AltSetting as a default setting.\n");
                if (!usb_endpoint_is_int_out(*endpoint)) {
-                       BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT,
-                                       DRV_ENTRY, DBG_LVL_ALL,
+                       BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT, DRV_ENTRY,
+                                       DBG_LVL_ALL,
                                        "Dongle does not have BCM16 Fix.\n");
                        /* change the EP2, EP4 to INT OUT end point and use EP4 in altsetting */
-                       ConfigureEndPointTypesThroughEEPROM(
-                                       psAd);
+                       ConfigureEndPointTypesThroughEEPROM(psAd);
 
                        /*
                         * It resets the device and if any thing
@@ -465,13 +457,10 @@ static int select_alternate_setting_for_highspeed_modem(
                         * will show fail and re-enumerate the
                         * device
                         */
-                       retval = usb_reset_device(
-                                       psIntfAdapter->udev);
+                       retval = usb_reset_device(psIntfAdapter->udev);
                        if (retval) {
-                               BCM_DEBUG_PRINT(psAd,
-                                               DBG_TYPE_INITEXIT,
-                                               DRV_ENTRY,
-                                               DBG_LVL_ALL,
+                               BCM_DEBUG_PRINT(psAd, DBG_TYPE_INITEXIT,
+                                               DRV_ENTRY, DBG_LVL_ALL,
                                                "reset failed.  Re-enumerating the device.\n");
                                return retval;
                        }