mfd: cros_ec: Add Management API entry points

Add commands for test and management.
Add command space for future development.

Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

diff --git a/include/linux/mfd/cros_ec_commands.h b/include/linux/mfd/cros_ec_commands.h
index 860a762743340de1a3677f1bf4d8aa7df88b046d..fc8babce1576e341abf0016e9e6143030bfbb049 100644 (file)
--- a/include/linux/mfd/cros_ec_commands.h
+++ b/include/linux/mfd/cros_ec_commands.h
@@ -5176,6 +5176,119 @@ struct ec_params_set_cbi {
        uint8_t data[];         /* For string and raw data */
 } __ec_align1;
 
+/*
+ * Information about resets of the AP by the EC and the EC's own uptime.
+ */
+#define EC_CMD_GET_UPTIME_INFO 0x0121
+
+struct ec_response_uptime_info {
+       /*
+        * Number of milliseconds since the last EC boot. Sysjump resets
+        * typically do not restart the EC's time_since_boot epoch.
+        *
+        * WARNING: The EC's sense of time is much less accurate than the AP's
+        * sense of time, in both phase and frequency.  This timebase is similar
+        * to CLOCK_MONOTONIC_RAW, but with 1% or more frequency error.
+        */
+       uint32_t time_since_ec_boot_ms;
+
+       /*
+        * Number of times the AP was reset by the EC since the last EC boot.
+        * Note that the AP may be held in reset by the EC during the initial
+        * boot sequence, such that the very first AP boot may count as more
+        * than one here.
+        */
+       uint32_t ap_resets_since_ec_boot;
+
+       /*
+        * The set of flags which describe the EC's most recent reset.  See
+        * include/system.h RESET_FLAG_* for details.
+        */
+       uint32_t ec_reset_flags;
+
+       /* Empty log entries have both the cause and timestamp set to zero. */
+       struct ap_reset_log_entry {
+               /*
+                * See include/chipset.h: enum chipset_{reset,shutdown}_reason
+                * for details.
+                */
+               uint16_t reset_cause;
+
+               /* Reserved for protocol growth. */
+               uint16_t reserved;
+
+               /*
+                * The time of the reset's assertion, in milliseconds since the
+                * last EC boot, in the same epoch as time_since_ec_boot_ms.
+                * Set to zero if the log entry is empty.
+                */
+               uint32_t reset_time_ms;
+       } recent_ap_reset[4];
+} __ec_align4;
+
+/*
+ * Add entropy to the device secret (stored in the rollback region).
+ *
+ * Depending on the chip, the operation may take a long time (e.g. to erase
+ * flash), so the commands are asynchronous.
+ */
+#define EC_CMD_ADD_ENTROPY     0x0122
+
+enum add_entropy_action {
+       /* Add entropy to the current secret. */
+       ADD_ENTROPY_ASYNC = 0,
+       /*
+        * Add entropy, and also make sure that the previous secret is erased.
+        * (this can be implemented by adding entropy multiple times until
+        * all rolback blocks have been overwritten).
+        */
+       ADD_ENTROPY_RESET_ASYNC = 1,
+       /* Read back result from the previous operation. */
+       ADD_ENTROPY_GET_RESULT = 2,
+};
+
+struct ec_params_rollback_add_entropy {
+       uint8_t action;
+} __ec_align1;
+
+/*
+ * Perform a single read of a given ADC channel.
+ */
+#define EC_CMD_ADC_READ                0x0123
+
+struct ec_params_adc_read {
+       uint8_t adc_channel;
+} __ec_align1;
+
+struct ec_response_adc_read {
+       int32_t adc_value;
+} __ec_align4;
+
+/*
+ * Read back rollback info
+ */
+#define EC_CMD_ROLLBACK_INFO           0x0124
+
+struct ec_response_rollback_info {
+       int32_t id; /* Incrementing number to indicate which region to use. */
+       int32_t rollback_min_version;
+       int32_t rw_rollback_version;
+} __ec_align4;
+
+
+/* Issue AP reset */
+#define EC_CMD_AP_RESET 0x0125
+
+/*****************************************************************************/
+/* The command range 0x200-0x2FF is reserved for Rotor. */
+
+/*****************************************************************************/
+/*
+ * Reserve a range of host commands for the CR51 firmware.
+ */
+#define EC_CMD_CR51_BASE 0x0300
+#define EC_CMD_CR51_LAST 0x03FF
+
 /*****************************************************************************/
 /* Fingerprint MCU commands: range 0x0400-0x040x */