ramips: Add support for SERCOMM NA502

The SERCOMM NA502 is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.

Note: BLE is currently unsupported.

Specifications
--------------

  - MT7621ST 880MHz, Single-Core, Dual-Thread
  - MT7603EN 2.4GHz WiFi
  - MT7662EN 5GHz WiFi + BLE
  - 128MiB NAND
  - 256MiB DDR3 RAM
  - SD3503 ZWave Controller
  - EM357 Zigbee Coordinator

MAC address assignment
----------------------

LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.

Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.

Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.

If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with

mtd unlock ubi
mtd erase ubi

This should only be needed once.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
[use kiB for IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a3d8c1295ed9eeceabd78ab86e73b151ae2868a9)

diff --git a/target/linux/ramips/dts/mt7621_sercomm_na502.dts b/target/linux/ramips/dts/mt7621_sercomm_na502.dts
new file mode 100644 (file)
index 0000000..af55d10
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_sercomm_na502.dts
@@ -0,0 +1,212 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "sercomm,na502", "mediatek,mt7621-soc";
+       model = "SERCOMM NA502";
+
+       aliases {
+               led-boot = &led_power;
+               led-failsafe = &led_power;
+               led-running = &led_power;
+               led-upgrade = &led_power;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_power: power {
+                       label = "green:power";
+                       gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+               };
+
+               internet {
+                       label = "green:internet";
+                       gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
+               };
+
+               wifi {
+                       label = "green:wifi";
+                       gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0tpt";
+               };
+
+               zwave {
+                       label = "green:zwave";
+                       gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+               };
+
+               service {
+                       label = "green:service";
+                       gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
+               };
+
+               zigbee {
+                       label = "green:zigbee";
+                       gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+               };
+
+               bluetooth {
+                       label = "green:bluetooth";
+                       gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+
+               select {
+                       label = "select";
+                       gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+                       linux,code = <BTN_0>;
+               };
+
+               sync {
+                       label = "sync";
+                       gpios = <&gpio 32 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RFKILL>;
+               };
+       };
+
+       gpio-export {
+               compatible = "gpio-export";
+
+               zwave_reset {
+                       gpio-export,name = "zwave_reset";
+                       gpio-export,output = <1>;
+                       gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+               };
+
+               zigbee_reset {
+                       gpio-export,name = "zigbee_reset";
+                       gpio-export,output = <1>;
+                       gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+               };
+       };
+};
+
+&gmac0 {
+       mtd-mac-address = <&factory 0xe000>;
+};
+
+&nand {
+       status = "okay";
+
+       partitions {
+               compatible = "fixed-partitions";
+               #address-cells = <1>;
+               #size-cells = <1>;
+
+               partition@0 {
+                       label = "u-boot";
+                       reg = <0x0 0x80000>;
+                       read-only;
+               };
+
+               partition@80000 {
+                       label = "config";
+                       reg = <0x80000 0x80000>;
+                       read-only;
+               };
+
+               factory: partition@100000 {
+                       label = "factory";
+                       reg = <0x100000 0x40000>;
+               };
+
+               partition@140000 {
+                       label = "kernel1";
+                       reg = <0x140000 0x1400000>;
+               };
+
+               partition@1540000 {
+                       label = "kernel";
+                       reg = <0x1540000 0x400000>;
+               };
+
+               partition@1940000 {
+                       label = "ubi";
+                       reg = <0x1940000 0x1000000>;
+               };
+
+               partition@2940000 {
+                       label = "user_storage";
+                       reg = <0x2940000 0x100000>;
+               };
+
+               partition@2a40000 {
+                       label = "data";
+                       reg = <0x2a40000 0x1000000>;
+               };
+
+               partition@3a40000 {
+                       label = "storage";
+                       reg = <0x3a40000 0x3200000>;
+               };
+
+               partition@6c40000 {
+                       label = "backup";
+                       reg = <0x6c40000 0x1340000>;
+               };
+       };
+};
+
+&pcie {
+       status = "okay";
+};
+
+&pcie0 {
+       wifi@0,0 {
+               compatible = "mediatek,mt76";
+               reg = <0x0000 0 0 0 0>;
+               mediatek,mtd-eeprom = <&factory 0x8000>;
+               mtd-mac-address = <&factory 0xe000>;
+               mtd-mac-address-increment = <1>;
+               ieee80211-freq-limit = <5000000 6000000>;
+       };
+};
+
+&pcie1 {
+       wifi@0,0 {
+               compatible = "mediatek,mt76";
+               reg = <0x0 0 0 0 0>;
+               mediatek,mtd-eeprom = <&factory 0x0000>;
+               mtd-mac-address = <&factory 0xe000>;
+               mtd-mac-address-increment = <2>;
+               ieee80211-freq-limit = <2400000 2500000>;
+       };
+};
+
+&state_default {
+       gpio {
+               groups = "jtag", "rgmii2";
+               function = "gpio";
+       };
+};
+
+&switch0 {
+       ports {
+               port@4 {
+                       status = "okay";
+                       label = "lan";
+               };
+       };
+};
+
+&uartlite2 {
+       status = "okay";
+};
+
+&uartlite3 {
+       status = "okay";
+};

diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 6645c7b06e5f29706d6b37bb94df1da374ed38bf..a3bc14d59d9923aac77be2f76a2289c05282259e 100644 (file)
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -1167,6 +1167,20 @@ define Device/samknows_whitebox-v8
 endef
 TARGET_DEVICES += samknows_whitebox-v8
 
+define Device/sercomm_na502
+  $(Device/uimage-lzma-loader)
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  IMAGE_SIZE := 20480k
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+  UBINIZE_OPTS := -E 5
+  KERNEL_SIZE := 4096k
+  DEVICE_VENDOR := SERCOMM
+  DEVICE_MODEL := NA502
+  DEVICE_PACKAGES := kmod-mt76x2 kmod-mt7603 kmod-usb3
+endef
+TARGET_DEVICES += sercomm_na502
+
 define Device/storylink_sap-g3200u3
   $(Device/dsa-migration)
   IMAGE_SIZE := 7872k

diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
index c0c767306af795d4a734c71f75ca08b6a761627b..4b44669b8496af47f6d9391fc0e0bdd2ed2504a6 100755 (executable)
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
@@ -13,6 +13,7 @@ ramips_setup_interfaces()
        edimax,re23s|\
        mikrotik,routerboard-m11g|\
        netgear,ex6150|\
+       sercomm,na502|\
        thunder,timecloud|\
        tplink,re350-v1|\
        tplink,re500-v1|\

diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
index 4943ad1305485e3997bab17a08490d331644ccda..c2ad4d3ed63ebee9207e3323c2df3247b7fbd615 100755 (executable)
--- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
@@ -72,6 +72,7 @@ platform_do_upgrade() {
        netgear,wac104|\
        netgear,wac124|\
        netis,wf2881|\
+       sercomm,na502|\
        xiaomi,mi-router-3g|\
        xiaomi,mi-router-3-pro|\
        xiaomi,mi-router-4|\