w1: w1-gpio: Convert to use GPIO descriptors

The w1 master driver includes a complete open drain emulation
reimplementation among other things.

This converts the driver and all board files using it to use
GPIO descriptors associated with the device to look up the
GPIO wire, as well ass the optional pull-up GPIO line.

When probed from the device tree, the driver will just pick
descriptors and use them right off. For the two board files
in the kernel, we add descriptor lookups so we do not need
to keep any old platform data handling around for the GPIO
lines.

As the platform data is also a state container for this driver,
we augment it to contain the GPIO descriptors.

w1_gpio_write_bit_dir() and w1_gpio_write_bit_val() are gone
since this pair was a reimplementation of open drain emulation
which is now handled by gpiolib.

The special "linux,open-drain" flag is a bit of mishap here:
it has the same semantic as the same flags in I2C: it means
that something in the platform is setting up the line as
open drain behind our back. We handle this the same way as
in I2C.

To drive the pull-up, we need to bypass open drain emulation
in gpiolib for the line, and this is done by driving it high
using gpiod_set_raw_value() which has been augmented to have
the semantic of overriding the open drain emulation.

We also augment the documentation to reflect the way to pass
GPIO descriptors from the machine.

Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

diff --git a/Documentation/w1/masters/w1-gpio b/Documentation/w1/masters/w1-gpio
index af5d3b4aa851501da0687d6414c0f070c574a7aa..623961d9e83fd80a0a3cf4dd39de8bbef8ff605e 100644 (file)
--- a/Documentation/w1/masters/w1-gpio
+++ b/Documentation/w1/masters/w1-gpio
@@ -8,17 +8,27 @@ Description
 -----------
 
 GPIO 1-wire bus master driver. The driver uses the GPIO API to control the
-wire and the GPIO pin can be specified using platform data.
+wire and the GPIO pin can be specified using GPIO machine descriptor tables.
+It is also possible to define the master using device tree, see
+Documentation/devicetree/bindings/w1/w1-gpio.txt
 
 
 Example (mach-at91)
 -------------------
 
+#include <linux/gpio/machine.h>
 #include <linux/w1-gpio.h>
 
+static struct gpiod_lookup_table foo_w1_gpiod_table = {
+       .dev_id = "w1-gpio",
+       .table = {
+               GPIO_LOOKUP_IDX("at91-gpio", AT91_PIN_PB20, NULL, 0,
+                       GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN),
+       },
+};
+
 static struct w1_gpio_platform_data foo_w1_gpio_pdata = {
-       .pin            = AT91_PIN_PB20,
-       .is_open_drain  = 1,
+       .ext_pullup_enable_pin  = -EINVAL,
 };
 
 static struct platform_device foo_w1_device = {
@@ -30,4 +40,5 @@ static struct platform_device foo_w1_device = {
 ...
        at91_set_GPIO_periph(foo_w1_gpio_pdata.pin, 1);
        at91_set_multi_drive(foo_w1_gpio_pdata.pin, 1);
+       gpiod_add_lookup_table(&foo_w1_gpiod_table);
        platform_device_register(&foo_w1_device);

diff --git a/arch/arm/mach-ixp4xx/vulcan-setup.c b/arch/arm/mach-ixp4xx/vulcan-setup.c
index 731fb2019ecb84be4e268ff6fcb9a967b8217563..2c03d2f6b6479b2b1423e347b1b69998e65810a9 100644 (file)
--- a/arch/arm/mach-ixp4xx/vulcan-setup.c
+++ b/arch/arm/mach-ixp4xx/vulcan-setup.c
@@ -16,6 +16,7 @@
 #include <linux/serial_8250.h>
 #include <linux/io.h>
 #include <linux/w1-gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/mtd/plat-ram.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -162,9 +163,16 @@ static struct platform_device vulcan_max6369 = {
        .num_resources          = 1,
 };
 
+static struct gpiod_lookup_table vulcan_w1_gpiod_table = {
+       .dev_id = "w1-gpio",
+       .table = {
+               GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", 14, NULL, 0,
+                               GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+       },
+};
+
 static struct w1_gpio_platform_data vulcan_w1_gpio_pdata = {
-       .pin                    = 14,
-       .ext_pullup_enable_pin  = -EINVAL,
+       /* Intentionally left blank */
 };
 
 static struct platform_device vulcan_w1_gpio = {
@@ -233,6 +241,7 @@ static void __init vulcan_init(void)
                          IXP4XX_EXP_BUS_WR_EN          |
                          IXP4XX_EXP_BUS_BYTE_EN;
 
+       gpiod_add_lookup_table(&vulcan_w1_gpiod_table);
        platform_add_devices(vulcan_devices, ARRAY_SIZE(vulcan_devices));
 }
 

diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c
index 9d662fed03ec7ae7fbf05bd22775185b00e571b6..feddca7f3540e4b41e9075425dd2cfe5f0e335f3 100644 (file)
--- a/arch/arm/mach-pxa/raumfeld.c
+++ b/arch/arm/mach-pxa/raumfeld.c
@@ -506,11 +506,16 @@ static void w1_enable_external_pullup(int enable)
        msleep(100);
 }
 
+static struct gpiod_lookup_table raumfeld_w1_gpiod_table = {
+       .dev_id = "w1-gpio",
+       .table = {
+               GPIO_LOOKUP_IDX("gpio-pxa", GPIO_ONE_WIRE, NULL, 0,
+                               GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+       },
+};
+
 static struct w1_gpio_platform_data w1_gpio_platform_data = {
-       .pin                    = GPIO_ONE_WIRE,
-       .is_open_drain          = 0,
-       .enable_external_pullup = w1_enable_external_pullup,
-       .ext_pullup_enable_pin  = -EINVAL,
+       .enable_external_pullup = w1_enable_external_pullup,
 };
 
 static struct platform_device raumfeld_w1_gpio_device = {
@@ -523,13 +528,14 @@ static struct platform_device raumfeld_w1_gpio_device = {
 static void __init raumfeld_w1_init(void)
 {
        int ret = gpio_request(GPIO_W1_PULLUP_ENABLE,
-                               "W1 external pullup enable");
+                               "W1 external pullup enable");
 
        if (ret < 0)
                pr_warn("Unable to request GPIO_W1_PULLUP_ENABLE\n");
        else
                gpio_direction_output(GPIO_W1_PULLUP_ENABLE, 0);
 
+       gpiod_add_lookup_table(&raumfeld_w1_gpiod_table);
        platform_device_register(&raumfeld_w1_gpio_device);
 }
 

diff --git a/drivers/w1/masters/w1-gpio.c b/drivers/w1/masters/w1-gpio.c
index a90728ceec5ad8968489021f9da44e161f399998..55e11bf8ebaf37732c6566aec0ee1e335e9cfdb9 100644 (file)
--- a/drivers/w1/masters/w1-gpio.c
+++ b/drivers/w1/masters/w1-gpio.c
@@ -13,9 +13,8 @@
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/w1-gpio.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/of_platform.h>
-#include <linux/of_gpio.h>
 #include <linux/err.h>
 #include <linux/of.h>
 #include <linux/delay.h>
@@ -30,11 +29,17 @@ static u8 w1_gpio_set_pullup(void *data, int delay)
                pdata->pullup_duration = delay;
        } else {
                if (pdata->pullup_duration) {
-                       gpio_direction_output(pdata->pin, 1);
-
+                       /*
+                        * This will OVERRIDE open drain emulation and force-pull
+                        * the line high for some time.
+                        */
+                       gpiod_set_raw_value(pdata->gpiod, 1);
                        msleep(pdata->pullup_duration);
-
-                       gpio_direction_input(pdata->pin);
+                       /*
+                        * This will simply set the line as input since we are doing
+                        * open drain emulation in the GPIO library.
+                        */
+                       gpiod_set_value(pdata->gpiod, 1);
                }
                pdata->pullup_duration = 0;
        }
@@ -42,28 +47,18 @@ static u8 w1_gpio_set_pullup(void *data, int delay)
        return 0;
 }
 
-static void w1_gpio_write_bit_dir(void *data, u8 bit)
-{
-       struct w1_gpio_platform_data *pdata = data;
-
-       if (bit)
-               gpio_direction_input(pdata->pin);
-       else
-               gpio_direction_output(pdata->pin, 0);
-}
-
-static void w1_gpio_write_bit_val(void *data, u8 bit)
+static void w1_gpio_write_bit(void *data, u8 bit)
 {
        struct w1_gpio_platform_data *pdata = data;
 
-       gpio_set_value(pdata->pin, bit);
+       gpiod_set_value(pdata->gpiod, bit);
 }
 
 static u8 w1_gpio_read_bit(void *data)
 {
        struct w1_gpio_platform_data *pdata = data;
 
-       return gpio_get_value(pdata->pin) ? 1 : 0;
+       return gpiod_get_value(pdata->gpiod) ? 1 : 0;
 }
 
 #if defined(CONFIG_OF)
@@ -74,107 +69,85 @@ static const struct of_device_id w1_gpio_dt_ids[] = {
 MODULE_DEVICE_TABLE(of, w1_gpio_dt_ids);
 #endif
 
-static int w1_gpio_probe_dt(struct platform_device *pdev)
-{
-       struct w1_gpio_platform_data *pdata = dev_get_platdata(&pdev->dev);
-       struct device_node *np = pdev->dev.of_node;
-       int gpio;
-
-       pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
-       if (!pdata)
-               return -ENOMEM;
-
-       if (of_get_property(np, "linux,open-drain", NULL))
-               pdata->is_open_drain = 1;
-
-       gpio = of_get_gpio(np, 0);
-       if (gpio < 0) {
-               if (gpio != -EPROBE_DEFER)
-                       dev_err(&pdev->dev,
-                                       "Failed to parse gpio property for data pin (%d)\n",
-                                       gpio);
-
-               return gpio;
-       }
-       pdata->pin = gpio;
-
-       gpio = of_get_gpio(np, 1);
-       if (gpio == -EPROBE_DEFER)
-               return gpio;
-       /* ignore other errors as the pullup gpio is optional */
-       pdata->ext_pullup_enable_pin = gpio;
-
-       pdev->dev.platform_data = pdata;
-
-       return 0;
-}
-
 static int w1_gpio_probe(struct platform_device *pdev)
 {
        struct w1_bus_master *master;
        struct w1_gpio_platform_data *pdata;
+       struct device *dev = &pdev->dev;
+       struct device_node *np = dev->of_node;
+       /* Enforce open drain mode by default */
+       enum gpiod_flags gflags = GPIOD_OUT_LOW_OPEN_DRAIN;
        int err;
 
        if (of_have_populated_dt()) {
-               err = w1_gpio_probe_dt(pdev);
-               if (err < 0)
-                       return err;
+               pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+               if (!pdata)
+                       return -ENOMEM;
+
+               /*
+                * This parameter means that something else than the gpiolib has
+                * already set the line into open drain mode, so we should just
+                * driver it high/low like we are in full control of the line and
+                * open drain will happen transparently.
+                */
+               if (of_get_property(np, "linux,open-drain", NULL))
+                       gflags = GPIOD_OUT_LOW;
+
+               pdev->dev.platform_data = pdata;
        }
-
-       pdata = dev_get_platdata(&pdev->dev);
+       pdata = dev_get_platdata(dev);
 
        if (!pdata) {
-               dev_err(&pdev->dev, "No configuration data\n");
+               dev_err(dev, "No configuration data\n");
                return -ENXIO;
        }
 
-       master = devm_kzalloc(&pdev->dev, sizeof(struct w1_bus_master),
+       master = devm_kzalloc(dev, sizeof(struct w1_bus_master),
                        GFP_KERNEL);
        if (!master) {
-               dev_err(&pdev->dev, "Out of memory\n");
+               dev_err(dev, "Out of memory\n");
                return -ENOMEM;
        }
 
-       err = devm_gpio_request(&pdev->dev, pdata->pin, "w1");
-       if (err) {
-               dev_err(&pdev->dev, "gpio_request (pin) failed\n");
-               return err;
+       pdata->gpiod = devm_gpiod_get_index(dev, NULL, 0, gflags);
+       if (IS_ERR(pdata->gpiod)) {
+               dev_err(dev, "gpio_request (pin) failed\n");
+               return PTR_ERR(pdata->gpiod);
        }
 
-       if (gpio_is_valid(pdata->ext_pullup_enable_pin)) {
-               err = devm_gpio_request_one(&pdev->dev,
-                               pdata->ext_pullup_enable_pin, GPIOF_INIT_LOW,
-                               "w1 pullup");
-               if (err < 0) {
-                       dev_err(&pdev->dev, "gpio_request_one "
-                                       "(ext_pullup_enable_pin) failed\n");
-                       return err;
-               }
+       pdata->pullup_gpiod =
+               devm_gpiod_get_index_optional(dev, NULL, 1, GPIOD_OUT_LOW);
+       if (IS_ERR(pdata->pullup_gpiod)) {
+               dev_err(dev, "gpio_request_one "
+                       "(ext_pullup_enable_pin) failed\n");
+               return PTR_ERR(pdata->pullup_gpiod);
        }
 
        master->data = pdata;
        master->read_bit = w1_gpio_read_bit;
-
-       if (pdata->is_open_drain) {
-               gpio_direction_output(pdata->pin, 1);
-               master->write_bit = w1_gpio_write_bit_val;
-       } else {
-               gpio_direction_input(pdata->pin);
-               master->write_bit = w1_gpio_write_bit_dir;
+       gpiod_direction_output(pdata->gpiod, 1);
+       master->write_bit = w1_gpio_write_bit;
+
+       /*
+        * If we are using open drain emulation from the GPIO library,
+        * we need to use this pullup function that hammers the line
+        * high using a raw accessor to provide pull-up for the w1
+        * line.
+        */
+       if (gflags == GPIOD_OUT_LOW_OPEN_DRAIN)
                master->set_pullup = w1_gpio_set_pullup;
-       }
 
        err = w1_add_master_device(master);
        if (err) {
-               dev_err(&pdev->dev, "w1_add_master device failed\n");
+               dev_err(dev, "w1_add_master device failed\n");
                return err;
        }
 
        if (pdata->enable_external_pullup)
                pdata->enable_external_pullup(1);
 
-       if (gpio_is_valid(pdata->ext_pullup_enable_pin))
-               gpio_set_value(pdata->ext_pullup_enable_pin, 1);
+       if (pdata->pullup_gpiod)
+               gpiod_set_value(pdata->pullup_gpiod, 1);
 
        platform_set_drvdata(pdev, master);
 
@@ -189,8 +162,8 @@ static int w1_gpio_remove(struct platform_device *pdev)
        if (pdata->enable_external_pullup)
                pdata->enable_external_pullup(0);
 
-       if (gpio_is_valid(pdata->ext_pullup_enable_pin))
-               gpio_set_value(pdata->ext_pullup_enable_pin, 0);
+       if (pdata->pullup_gpiod)
+               gpiod_set_value(pdata->pullup_gpiod, 0);
 
        w1_remove_master_device(master);
 

diff --git a/include/linux/w1-gpio.h b/include/linux/w1-gpio.h
index d58594a3232492e33f1dd4babd3798b03e0f0203..78901ecd2f957a0ca171ac980cb77b7166a2f047 100644 (file)
--- a/include/linux/w1-gpio.h
+++ b/include/linux/w1-gpio.h
@@ -10,16 +10,15 @@
 #ifndef _LINUX_W1_GPIO_H
 #define _LINUX_W1_GPIO_H
 
+struct gpio_desc;
+
 /**
  * struct w1_gpio_platform_data - Platform-dependent data for w1-gpio
- * @pin: GPIO pin to use
- * @is_open_drain: GPIO pin is configured as open drain
  */
 struct w1_gpio_platform_data {
-       unsigned int pin;
-       unsigned int is_open_drain:1;
+       struct gpio_desc *gpiod;
+       struct gpio_desc *pullup_gpiod;
        void (*enable_external_pullup)(int enable);
-       unsigned int ext_pullup_enable_pin;
        unsigned int pullup_duration;
 };