#include "comedi_fc.h"
+/*
+ * Register I/O map
+ *
+ * Offset Page 0 Page 1 Page 2 Page 3
+ * ------ ----------- ----------- ----------- -----------
+ * 0x00 Port 0 I/O Port 0 I/O Port 0 I/O Port 0 I/O
+ * 0x01 Port 1 I/O Port 1 I/O Port 1 I/O Port 1 I/O
+ * 0x02 Port 2 I/O Port 2 I/O Port 2 I/O Port 2 I/O
+ * 0x03 Port 3 I/O Port 3 I/O Port 3 I/O Port 3 I/O
+ * 0x04 Port 4 I/O Port 4 I/O Port 4 I/O Port 4 I/O
+ * 0x05 Port 5 I/O Port 5 I/O Port 5 I/O Port 5 I/O
+ * 0x06 INT_PENDING INT_PENDING INT_PENDING INT_PENDING
+ * 0x07 Page/Lock Page/Lock Page/Lock Page/Lock
+ * 0x08 N/A POL_0 ENAB_0 INT_ID0
+ * 0x09 N/A POL_1 ENAB_1 INT_ID1
+ * 0x0a N/A POL_2 ENAB_2 INT_ID2
+ */
+#define PCMUIO_PORT_REG(x) (0x00 + (x))
+#define PCMUIO_INT_PENDING_REG 0x06
+#define PCMUIO_PAGE_LOCK_REG 0x07
+#define PCMUIO_LOCK_PORT(x) ((1 << (x)) & 0x3f)
+#define PCMUIO_PAGE(x) (((x) & 0x3) << 6)
+#define PCMUIO_PAGE_MASK PCMUIO_PAGE(3)
+#define PCMUIO_PAGE_POL 1
+#define PCMUIO_PAGE_ENAB 2
+#define PCMUIO_PAGE_INT_ID 3
+#define PCMUIO_PAGE_REG(x) (0x08 + (x))
+
#define CHANS_PER_PORT 8
#define PORTS_PER_ASIC 6
#define INTR_PORTS_PER_ASIC 3
#define PCMUIO48_IOSIZE ASIC_IOSIZE
#define PCMUIO96_IOSIZE (ASIC_IOSIZE * 2)
-/*
- * Some offsets - these are all in the 16byte IO memory offset from
- * the base address. Note that there is a paging scheme to swap out
- * offsets 0x8-0xA using the PAGELOCK register. See the table below.
- *
- * Register(s) Pages R/W? Description
- * --------------------------------------------------------------------------
- * REG_PORTx All R/W Read/Write/Configure IO
- * REG_INT_PENDING All ReadOnly Which INT_IDx has int.
- * REG_PAGELOCK All WriteOnly Select a page
- * REG_POLx Pg. 1 only WriteOnly Select edge-detection polarity
- * REG_ENABx Pg. 2 only WriteOnly Enable/Disable edge-detect int.
- * REG_INT_IDx Pg. 3 only R/W See which ports/bits have ints.
- */
-#define REG_PORT0 0x0
-#define REG_PORT1 0x1
-#define REG_PORT2 0x2
-#define REG_PORT3 0x3
-#define REG_PORT4 0x4
-#define REG_PORT5 0x5
-#define REG_INT_PENDING 0x6
-/*
- * page selector register
- * Upper 2 bits select a page and bits 0-5 are used to
- * 'lock down' a particular port above to make it readonly.
- */
-#define REG_PAGELOCK 0x7
-#define REG_POL0 0x8
-#define REG_POL1 0x9
-#define REG_POL2 0xa
-#define REG_ENAB0 0x8
-#define REG_ENAB1 0x9
-#define REG_ENAB2 0xa
-#define REG_INT_ID0 0x8
-#define REG_INT_ID1 0x9
-#define REG_INT_ID2 0xa
-
#define NUM_PAGED_REGS 3
#define NUM_PAGES 4
#define FIRST_PAGED_REG 0x8
-#define REG_PAGE_BITOFFSET 6
-#define REG_LOCK_BITOFFSET 0
-#define REG_PAGE_MASK (~((0x1 << REG_PAGE_BITOFFSET) - 1))
-#define REG_LOCK_MASK ~(REG_PAGE_MASK)
-#define PAGE_POL 1
-#define PAGE_ENAB 2
-#define PAGE_INT_ID 3
struct pcmuio_board {
const char *name;
if (page < 0 || page >= NUM_PAGES)
return; /* more paranoia */
- devpriv->asics[asic].pagelock &= ~REG_PAGE_MASK;
- devpriv->asics[asic].pagelock |= page << REG_PAGE_BITOFFSET;
+ devpriv->asics[asic].pagelock &= ~PCMUIO_PAGE_MASK;
+ devpriv->asics[asic].pagelock |= PCMUIO_PAGE(page);
/* now write out the shadow register */
outb(devpriv->asics[asic].pagelock,
- dev->iobase + ASIC_IOSIZE * asic + REG_PAGELOCK);
+ dev->iobase + ASIC_IOSIZE * asic + PCMUIO_PAGE_LOCK_REG);
}
static void init_asics(struct comedi_device *dev)
/* first, clear all the DIO port bits */
for (port = 0; port < PORTS_PER_ASIC; ++port)
- outb(0, baseaddr + REG_PORT0 + port);
+ outb(0, baseaddr + PCMUIO_PORT_REG(port));
/* Next, clear all the paged registers for each page */
for (page = 1; page < NUM_PAGES; ++page) {
outb(0, baseaddr + reg);
}
- /* DEBUG set rising edge interrupts on port0 of both asics */
- /*switch_page(dev, asic, PAGE_POL);
- outb(0xff, baseaddr + REG_POL0);
- switch_page(dev, asic, PAGE_ENAB);
- outb(0xff, baseaddr + REG_ENAB0); */
- /* END DEBUG */
-
/* switch back to default page 0 */
switch_page(dev, asic, 0);
}
s->async->inttrig = NULL;
nports = subpriv->intr.num_asic_chans / CHANS_PER_PORT;
firstport = subpriv->intr.asic_chan / CHANS_PER_PORT;
- switch_page(dev, asic, PAGE_ENAB);
+ switch_page(dev, asic, PCMUIO_PAGE_ENAB);
for (port = firstport; port < firstport + nports; ++port) {
/* disable all intrs for this subdev.. */
- outb(0, devpriv->asics[asic].iobase + REG_ENAB0 + port);
+ outb(0, devpriv->asics[asic].iobase + PCMUIO_PAGE_REG(port));
}
}
spin_lock_irqsave(&devpriv->asics[asic].spinlock, flags);
- int_pend = inb(iobase + REG_INT_PENDING) & 0x07;
+ int_pend = inb(iobase + PCMUIO_INT_PENDING_REG) & 0x07;
if (int_pend) {
for (i = 0; i < INTR_PORTS_PER_ASIC; ++i) {
if (int_pend & (0x1 << i)) {
unsigned char val;
- switch_page(dev, asic, PAGE_INT_ID);
- val = inb(iobase + REG_INT_ID0 + i);
+ switch_page(dev, asic, PCMUIO_PAGE_INT_ID);
+ val = inb(iobase + PCMUIO_PAGE_REG(i));
if (val)
/* clear pending interrupt */
- outb(0, iobase + REG_INT_ID0 + i);
+ outb(0, iobase + PCMUIO_PAGE_REG(i));
triggered |= (val << (i * 8));
}
1) << subpriv->intr.first_chan;
subpriv->intr.enabled_mask = bits;
- switch_page(dev, asic, PAGE_ENAB);
+ switch_page(dev, asic, PCMUIO_PAGE_ENAB);
for (port = firstport; port < firstport + nports; ++port) {
unsigned enab =
bits >> (subpriv->intr.first_chan + (port -
(port - firstport) * 8) & 0xff;
/* set enab intrs for this subdev.. */
outb(enab,
- devpriv->asics[asic].iobase + REG_ENAB0 + port);
- switch_page(dev, asic, PAGE_POL);
+ devpriv->asics[asic].iobase + PCMUIO_PAGE_REG(port));
+ switch_page(dev, asic, PCMUIO_PAGE_POL);
outb(pol,
- devpriv->asics[asic].iobase + REG_ENAB0 + port);
+ devpriv->asics[asic].iobase + PCMUIO_PAGE_REG(port));
}
}
return 0;
projects / openwrt / staging / blogic.git / commitdiff