pinctrl: at91-pio4: add support for drive strength

Add support for the drive strength configuration. Usually, this value is
expressed in mA. Since the numeric value depends on VDDIOP voltage, a
value we can't retrieve at runtime, the controller uses low, medium and
high to define the drive strength.

The PIO controller accepts two values for the low drive configuration: 0
and 1. Most of the time, we don't care about the drive strength. So we
keep the default value which is 0. The drive strength is advertised
through the sysfs only when it has been explicitly set in the device
tree i.e. if its value is different from 0.

Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt
index 61ac75706cc9c407a3dd47af838fa852c1b31514..04d16fb69eb7c5d260a908be0bc750eeeee3fe7a 100644 (file)
--- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt
@@ -36,6 +36,8 @@ Optional properties:
 - GENERIC_PINCONFIG: generic pinconfig options to use, bias-disable,
 bias-pull-down, bias-pull-up, drive-open-drain, input-schmitt-enable,
 input-debounce, output-low, output-high.
+- atmel,drive-strength: 0 or 1 for low drive, 2 for medium drive and 3 for
+high drive. The default value is low drive.
 
 Example:
 
@@ -66,6 +68,7 @@ Example:
                        pinmux = <PIN_PB0>,
                                 <PIN_PB5>;
                        bias-pull-up;
+                       atmel,drive-strength = <ATMEL_PIO_DRVSTR_ME>;
                };
 
                pinctrl_sdmmc1_default: sdmmc1_default {

diff --git a/drivers/pinctrl/pinctrl-at91-pio4.c b/drivers/pinctrl/pinctrl-at91-pio4.c
index 67e4d9ffa6b1f4e4825d59ea81e736fb59af6192..8f061971a7d116701a0657ebfe3308b69687877e 100644 (file)
--- a/drivers/pinctrl/pinctrl-at91-pio4.c
+++ b/drivers/pinctrl/pinctrl-at91-pio4.c
@@ -14,6 +14,7 @@
  * GNU General Public License for more details.
  */
 
+#include <dt-bindings/pinctrl/at91.h>
 #include <linux/clk.h>
 #include <linux/gpio/driver.h>
 /* FIXME: needed for gpio_to_irq(), get rid of this */
@@ -49,6 +50,8 @@
 #define                ATMEL_PIO_IFSCEN_MASK           BIT(13)
 #define                ATMEL_PIO_OPD_MASK              BIT(14)
 #define                ATMEL_PIO_SCHMITT_MASK          BIT(15)
+#define                ATMEL_PIO_DRVSTR_MASK           GENMASK(17, 16)
+#define                ATMEL_PIO_DRVSTR_OFFSET         16
 #define                ATMEL_PIO_CFGR_EVTSEL_MASK      GENMASK(26, 24)
 #define                ATMEL_PIO_CFGR_EVTSEL_FALLING   (0 << 24)
 #define                ATMEL_PIO_CFGR_EVTSEL_RISING    (1 << 24)
@@ -75,6 +78,9 @@
 #define ATMEL_GET_PIN_FUNC(pinfunc)    ((pinfunc >> 16) & 0xf)
 #define ATMEL_GET_PIN_IOSET(pinfunc)   ((pinfunc >> 20) & 0xf)
 
+/* Custom pinconf parameters */
+#define ATMEL_PIN_CONFIG_DRIVE_STRENGTH        (PIN_CONFIG_END + 1)
+
 struct atmel_pioctrl_data {
        unsigned nbanks;
 };
@@ -139,6 +145,10 @@ static const char * const atmel_functions[] = {
        "GPIO", "A", "B", "C", "D", "E", "F", "G"
 };
 
+static const struct pinconf_generic_params atmel_custom_bindings[] = {
+       {"atmel,drive-strength", ATMEL_PIN_CONFIG_DRIVE_STRENGTH, 0},
+};
+
 /* --- GPIO --- */
 static unsigned int atmel_gpio_read(struct atmel_pioctrl *atmel_pioctrl,
                                    unsigned int bank, unsigned int reg)
@@ -692,6 +702,11 @@ static int atmel_conf_pin_config_group_get(struct pinctrl_dev *pctldev,
                        return -EINVAL;
                arg = 1;
                break;
+       case ATMEL_PIN_CONFIG_DRIVE_STRENGTH:
+               if (!(res & ATMEL_PIO_DRVSTR_MASK))
+                       return -EINVAL;
+               arg = (res & ATMEL_PIO_DRVSTR_MASK) >> ATMEL_PIO_DRVSTR_OFFSET;
+               break;
        default:
                return -ENOTSUPP;
        }
@@ -777,6 +792,18 @@ static int atmel_conf_pin_config_group_set(struct pinctrl_dev *pctldev,
                                        ATMEL_PIO_SODR);
                        }
                        break;
+               case ATMEL_PIN_CONFIG_DRIVE_STRENGTH:
+                       switch (arg) {
+                       case ATMEL_PIO_DRVSTR_LO:
+                       case ATMEL_PIO_DRVSTR_ME:
+                       case ATMEL_PIO_DRVSTR_HI:
+                               conf &= (~ATMEL_PIO_DRVSTR_MASK);
+                               conf |= arg << ATMEL_PIO_DRVSTR_OFFSET;
+                               break;
+                       default:
+                               dev_warn(pctldev->dev, "drive strength not updated (incorrect value)\n");
+                       }
+                       break;
                default:
                        dev_warn(pctldev->dev,
                                 "unsupported configuration parameter: %u\n",
@@ -816,6 +843,19 @@ static void atmel_conf_pin_config_dbg_show(struct pinctrl_dev *pctldev,
                seq_printf(s, "%s ", "open-drain");
        if (conf & ATMEL_PIO_SCHMITT_MASK)
                seq_printf(s, "%s ", "schmitt");
+       if (conf & ATMEL_PIO_DRVSTR_MASK) {
+               switch ((conf & ATMEL_PIO_DRVSTR_MASK) >> ATMEL_PIO_DRVSTR_OFFSET) {
+               case ATMEL_PIO_DRVSTR_ME:
+                       seq_printf(s, "%s ", "medium-drive");
+                       break;
+               case ATMEL_PIO_DRVSTR_HI:
+                       seq_printf(s, "%s ", "high-drive");
+                       break;
+               /* ATMEL_PIO_DRVSTR_LO and 0 which is the default value at reset */
+               default:
+                       seq_printf(s, "%s ", "low-drive");
+               }
+       }
 }
 
 static const struct pinconf_ops atmel_confops = {
@@ -958,6 +998,8 @@ static int atmel_pinctrl_probe(struct platform_device *pdev)
                return -ENOMEM;
        atmel_pinctrl_desc.pins = pin_desc;
        atmel_pinctrl_desc.npins = atmel_pioctrl->npins;
+       atmel_pinctrl_desc.num_custom_params = ARRAY_SIZE(atmel_custom_bindings);
+       atmel_pinctrl_desc.custom_params = atmel_custom_bindings;
 
        /* One pin is one group since a pin can achieve all functions. */
        group_names = devm_kcalloc(dev,

diff --git a/include/dt-bindings/pinctrl/at91.h b/include/dt-bindings/pinctrl/at91.h
index 2732d6c0fb39ebd28ef4ec81d415fc0d0677c8e7..eb81867eac77eda6901aa1c7bdbdc0bc3a0313a2 100644 (file)
--- a/include/dt-bindings/pinctrl/at91.h
+++ b/include/dt-bindings/pinctrl/at91.h
@@ -39,4 +39,8 @@
 #define AT91_PERIPH_C          3
 #define AT91_PERIPH_D          4
 
+#define ATMEL_PIO_DRVSTR_LO    1
+#define ATMEL_PIO_DRVSTR_ME    2
+#define ATMEL_PIO_DRVSTR_HI    3
+
 #endif /* __DT_BINDINGS_AT91_PINCTRL_H__ */