From: Christian Lamparter Date: Wed, 4 Dec 2019 01:28:22 +0000 (+0100) Subject: ipq806x: ap148: reorganize dts X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=044c79689bc1117abc5eee394a7f8e312ac9f8d0;p=openwrt%2Fstaging%2Fjow.git ipq806x: ap148: reorganize dts Reorganize dts to use tags from ipq8064 dtsi Signed-off-by: Christian Lamparter Signed-off-by: Ansuel Smith --- diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts index 987731b04f..8ef5b92b52 100644 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts +++ b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts @@ -29,204 +29,198 @@ }; soc { - pinmux@800000 { - i2c4_pins: i2c4_pinmux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - bias-disable; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - drive-strength = <10>; - bias-none; - }; - }; - nand_pins: nand_pins { - mux { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38", "gpio39", - "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - pullups { - pins = "gpio39"; - bias-pull-up; - }; - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - bias-bus-hold; - }; - }; + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, + <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; }; - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; + phy4: ethernet-phy@4 { + reg = <4>; }; }; + }; +}; - gsbi@16300000 { - qcom,mode = ; - status = "okay"; - serial@16340000 { - status = "okay"; - }; +&qcom_pinmux { + i2c4_pins: i2c4_pinmux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + bias-disable; + }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ + nand_pins: nand_pins { + mux { + pins = "gpio34", "gpio35", "gpio36", + "gpio37", "gpio38", "gpio39", + "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + function = "nand"; + drive-strength = <10>; + bias-disable; + }; + pullups { + pins = "gpio39"; + bias-pull-up; }; + hold { + pins = "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + bias-bus-hold; + }; + }; - gsbi5: gsbi@1a200000 { - qcom,mode = ; - status = "okay"; + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; - spi4: spi@1a280000 { - status = "okay"; - spi-max-frequency = <50000000>; + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; +}; - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; +&adm_dma { + status = "okay"; +}; - cs-gpios = <&qcom_pinmux 20 0>; +&gsbi4 { + qcom,mode = ; + status = "okay"; - flash: m25p80@0 { - compatible = "s25fl256s1"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; + serial@16340000 { + status = "okay"; + }; - partitions { - compatible = "qcom,smem"; - }; - }; - }; - }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ +}; - sata-phy@1b400000 { - status = "okay"; - }; +&gsbi5 { + qcom,mode = ; + status = "okay"; - sata@29000000 { - status = "okay"; - }; + spi4: spi@1a280000 { + status = "okay"; + spi-max-frequency = <50000000>; - usb3_0: usb3@110f8800 { - status = "okay"; - }; + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; - usb3_1: usb3@100f8800 { - status = "okay"; - }; + cs-gpios = <&qcom_pinmux 20 0>; - pcie0: pci@1b500000 { - status = "okay"; - }; + flash: m25p80@0 { + compatible = "s25fl256s1"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; - pcie1: pci@1b700000 { - status = "okay"; - force_gen1 = <1>; + partitions { + compatible = "qcom,smem"; + }; }; + }; +}; - nand@1ac00000 { - status = "okay"; +&usb3_0 { + status = "okay"; +}; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; +&usb3_1 { + status = "okay"; +}; - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; +&pcie0 { + status = "okay"; +}; - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; +&pcie1 { + status = "okay"; + force_gen1 = <1>; +}; - partitions { - compatible = "qcom,smem"; - }; - }; - }; +&nand { + status = "okay"; - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; + cs0 { + reg = <0>; + compatible = "qcom,nandcs"; - phy4: ethernet-phy@4 { - reg = <4>; - }; + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "qcom,smem"; }; + }; +}; - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; + fixed-link { + speed = <1000>; + full-duplex; + }; +}; - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; + fixed-link { + speed = <1000>; + full-duplex; }; }; -&adm_dma { +&sata_phy { + status = "okay"; +}; + +&sata { status = "okay"; };