From: INAGAKI Hiroshi Date: Fri, 13 Sep 2019 15:14:36 +0000 (+0900) Subject: ramips: add support for ELECOM WRC-1167FS X-Git-Tag: v21.02.0-rc1~314 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=08768b44d9b6983ae8d2b96434225fef1f5f664c;p=openwrt%2Fopenwrt.git ramips: add support for ELECOM WRC-1167FS ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on MT7628AN. Specification: - SoC : MediaTek MT7628AN - RAM : DDR2 64 MiB (NT5TU32M16FG-AC) - Flash : SPI-NOR 16 MiB (W25Q128JVSIQ) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : MediaTek MT7628AN (SoC) - 5 GHz : MediaTek MT7612E - Ethernet : 10/100 Mbps x2 - Switch : MT7628AN (SoC) - LEDs/Keys : 6x, 3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: 3.3V, GND, TX, RX from "J1" marking - 57600n8 - Power : 12 VDC, 1 A Flash instruction using factory image: 1. Boot WRC-1167FS normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. Wait ~120 seconds to complete flashing Notes: - Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware - Additional padding in factory image is required to avoid incomplete flashing on stock firmware MAC addresses: - LAN : BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28 (hex)) - WAN : BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22 (hex)) - 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac (text) / Factory, 0x4 (hex)) - 5GHz : BC:5C:4C:xx:xx:6B (Config, rmac2 (text) / Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi --- diff --git a/target/linux/ramips/dts/mt7628an_elecom_wrc-1167fs.dts b/target/linux/ramips/dts/mt7628an_elecom_wrc-1167fs.dts new file mode 100644 index 0000000000..aa60b8a2c6 --- /dev/null +++ b/target/linux/ramips/dts/mt7628an_elecom_wrc-1167fs.dts @@ -0,0 +1,164 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7628an.dtsi" + +#include +#include + +/ { + compatible = "elecom,wrc-1167fs", "mediatek,mt7628an-soc"; + model = "ELECOM WRC-1167FS"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "green:power"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + }; + + wlan5g { + label = "green:wlan5g"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wps { + label = "red:wps"; + gpios = <&gpio 37 GPIO_ACTIVE_LOW>; + }; + + internet { + label = "green:internet"; + gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + }; + + lan { + label = "green:lan"; + gpios = <&gpio 40 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + label = "green:wlan2g"; + gpios = <&gpio 44 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; + + keys { + compatible = "gpio-keys"; + + ap { + label = "ap"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + reset { + label = "reset"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 38 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0x730000>; + }; + + partition@780000 { + label = "storage"; + reg = <0x780000 0x80000>; + read-only; + }; + }; + }; +}; + +&ehci { + status = "disabled"; +}; + +&esw { + mediatek,portmap = <0x2f>; + mediatek,portdisable = <0x27>; +}; + +ðernet { + mtd-mac-address = <&factory 0x28>; +}; + +&ohci { + status = "disabled"; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + ieee80211-freq-limit = <5000000 6000000>; + }; +}; + +&state_default { + gpio { + groups = "wled_an", "p3led_an", "p4led_an", "wdt", "refclk", "i2c", "i2s"; + function = "gpio"; + }; +}; + +&wmac { + status = "okay"; +}; diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk index 00976f6044..7ba2acacb8 100644 --- a/target/linux/ramips/image/mt76x8.mk +++ b/target/linux/ramips/image/mt76x8.mk @@ -6,6 +6,21 @@ include ./common-tp-link.mk DEFAULT_SOC := mt7628an +define Build/elecom-header + $(eval model_id=$(1)) + ( \ + fw_size="$$(printf '%08x' $$(stat -c%s $@))"; \ + echo -ne "$$(echo "031d6129$${fw_size}06000000$(model_id)" | \ + sed 's/../\\x&/g')"; \ + dd if=/dev/zero bs=92 count=1; \ + data_crc="$$(dd if=$@ | gzip -c | tail -c 8 | \ + od -An -N4 -tx4 --endian little | tr -d ' \n')"; \ + echo -ne "$$(echo "$${data_crc}00000000" | sed 's/../\\x&/g')"; \ + dd if=$@; \ + ) > $@.new + mv $@.new $@ +endef + define Build/ravpower-wd009-factory mkimage -A mips -T standalone -C none -a 0x80010000 -e 0x80010000 \ -n "OpenWrt Bootloader" -d $(UBOOT_PATH) $@.new @@ -93,6 +108,18 @@ define Device/duzun_dm06 endef TARGET_DEVICES += duzun_dm06 +define Device/elecom_wrc-1167fs + IMAGE_SIZE := 7360k + DEVICE_VENDOR := ELECOM + DEVICE_MODEL := WRC-1167FS + IMAGES += factory.bin + IMAGE/factory.bin := $$(sysupgrade_bin) | pad-to 64k | check-size | \ + xor-image -p 29944A25 -x | elecom-header 00228000 | \ + elecom-product-header WRC-1167FS + DEVICE_PACKAGES := kmod-mt76x2 +endef +TARGET_DEVICES += elecom_wrc-1167fs + define Device/glinet_gl-mt300n-v2 IMAGE_SIZE := 16064k DEVICE_VENDOR := GL.iNet diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds index bcbc2ed1e6..47b73e01a2 100755 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds @@ -25,6 +25,10 @@ cudy,wr1000) ucidef_set_led_switch "lan1" "lan1" "blue:lan1" "switch0" "0x08" ucidef_set_led_switch "lan2" "lan2" "blue:lan2" "switch0" "0x04" ;; +elecom,wrc-1167fs) + ucidef_set_led_switch "lan" "lan" "green:lan" "switch0" "0x8" + ucidef_set_led_switch "internet" "internet" "green:internet" "switch0" "0x10" + ;; glinet,gl-mt300n-v2) ucidef_set_led_netdev "wifi_led" "wifi" "red:wlan" "wlan0" ucidef_set_led_switch "wan" "wan" "green:wan" "switch0" "0x1" diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network index 8bbcbb2190..b741b4f9b4 100755 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network @@ -46,6 +46,7 @@ ramips_setup_interfaces() "0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0" ;; buffalo,wcr-1166ds|\ + elecom,wrc-1167fs|\ wavlink,wl-wn577a2) ucidef_add_switch "switch0" \ "3:lan" "4:wan" "6@eth0" @@ -181,6 +182,10 @@ ramips_setup_macs() zyxel,keenetic-extra-ii) wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x4)" 1) ;; + elecom,wrc-1167fs) + wan_mac=$(mtd_get_mac_binary factory 0x22) + label_mac=$wan_mac + ;; hilink,hlk-7628n) lan_mac=$(macaddr_setbit_la "$(cat /sys/class/net/eth0/address)") wan_mac=$(macaddr_add "$lan_mac" 1)