From: Birger Koblitz Date: Sun, 30 Jan 2022 05:20:25 +0000 (+0100) Subject: realtek: Add specific PHY polling options to support the Zyxel XGS1250/XGS1210 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=08cf48c344395d69bdd31cc4a9e9cde11295b8a5;p=openwrt%2Fstaging%2Faparcar.git realtek: Add specific PHY polling options to support the Zyxel XGS1250/XGS1210 Both the Aquantia AQR113c and the RTL8226 PHYs in the Zyxel XGS1250 and the Zyxel XGS1210 require special polling configuration settings in the RTL930X_SMI_10GPHY_POLLING_REGxx_CFG configuration registers. Set them. Additionally, for RTL 1GBit phys set the RTL930X_SMI_PRVTE_POLLING_CTRL bits in the poll mask. Signed-off-by: Birger Koblitz --- diff --git a/target/linux/realtek/files-5.10/drivers/net/ethernet/rtl838x_eth.c b/target/linux/realtek/files-5.10/drivers/net/ethernet/rtl838x_eth.c index 84b8a5b943..f13c4b0c02 100644 --- a/target/linux/realtek/files-5.10/drivers/net/ethernet/rtl838x_eth.c +++ b/target/linux/realtek/files-5.10/drivers/net/ethernet/rtl838x_eth.c @@ -199,6 +199,7 @@ struct rtl838x_eth_priv { u32 sds_id[MAX_PORTS]; bool smi_bus_isc45[MAX_SMI_BUSSES]; bool phy_is_internal[MAX_PORTS]; + phy_interface_t interfaces[MAX_PORTS]; }; extern int rtl838x_phy_init(struct rtl838x_eth_priv *priv); @@ -1468,11 +1469,12 @@ static void rtl838x_mac_pcs_get_state(struct phylink_config *config, struct rtl838x_eth_priv *priv = netdev_priv(dev); int port = priv->cpu_port; - pr_debug("In %s\n", __func__); + pr_info("In %s\n", __func__); state->link = priv->r->get_mac_link_sts(port) ? 1 : 0; state->duplex = priv->r->get_mac_link_dup_sts(port) ? 1 : 0; + pr_info("%s link status is %d\n", __func__, state->link); speed = priv->r->get_mac_link_spd_sts(port); switch (speed) { case 0: @@ -1785,6 +1787,9 @@ static int rtl839x_mdio_reset(struct mii_bus *bus) return 0; } +u8 mac_type_bit[RTL930X_CPU_PORT] = {0, 0, 0, 0, 2, 2, 2, 2, 4, 4, 4, 4, 6, 6, 6, 6, + 8, 8, 8, 8, 10, 10, 10, 10, 12, 15, 18, 21}; + static int rtl930x_mdio_reset(struct mii_bus *bus) { int i; @@ -1793,10 +1798,16 @@ static int rtl930x_mdio_reset(struct mii_bus *bus) u32 c45_mask = 0; u32 poll_sel[2]; u32 poll_ctrl = 0; + u32 private_poll_mask = 0; + u32 v; + bool uses_usxgmii = false; // For the Aquantia PHYs + bool uses_hisgmii = false; // For the RTL8221/8226 // Mapping of port to phy-addresses on an SMI bus poll_sel[0] = poll_sel[1] = 0; - for (i = 0; i < 28; i++) { + for (i = 0; i < RTL930X_CPU_PORT; i++) { + if (priv->smi_bus[i] > 3) + continue; pos = (i % 6) * 5; sw_w32_mask(0x1f << pos, priv->smi_addr[i] << pos, RTL930X_SMI_PORT0_5_ADDR + (i / 6) * 4); @@ -1810,8 +1821,8 @@ static int rtl930x_mdio_reset(struct mii_bus *bus) sw_w32(poll_sel[0], RTL930X_SMI_PORT0_15_POLLING_SEL); sw_w32(poll_sel[1], RTL930X_SMI_PORT16_27_POLLING_SEL); - // Enable polling on the respective SMI busses - sw_w32_mask(0, poll_ctrl, RTL930X_SMI_GLB_CTRL); + // Disable POLL_SEL for any SMI bus with a normal PHY (not RTL8295R for SFP+) + sw_w32_mask(poll_ctrl, 0, RTL930X_SMI_GLB_CTRL); // Configure which SMI busses are polled in c45 based on a c45 PHY being on that bus for (i = 0; i < 4; i++) @@ -1821,17 +1832,66 @@ static int rtl930x_mdio_reset(struct mii_bus *bus) pr_info("c45_mask: %08x\n", c45_mask); sw_w32_mask(0, c45_mask, RTL930X_SMI_GLB_CTRL); - // Ports 24 to 27 are 2.5 or 10Gig, set this type (1) or (0) for internal SerDes - for (i = 24; i < 28; i++) { - pos = (i - 24) * 3 + 12; - if (priv->phy_is_internal[i]) - sw_w32_mask(0x7 << pos, 0 << pos, RTL930X_SMI_MAC_TYPE_CTRL); - else - sw_w32_mask(0x7 << pos, 1 << pos, RTL930X_SMI_MAC_TYPE_CTRL); - } + // Set the MAC type of each port according to the PHY-interface + // Values are FE: 2, GE: 3, XGE/2.5G: 0(SERDES) or 1(otherwise), SXGE: 0 + v = 0; + for (i = 0; i < RTL930X_CPU_PORT; i++) { + switch (priv->interfaces[i]) { + case PHY_INTERFACE_MODE_10GBASER: + break; // Serdes: Value = 0 + + case PHY_INTERFACE_MODE_HSGMII: + private_poll_mask |= BIT(i); + // fallthrough + case PHY_INTERFACE_MODE_USXGMII: + v |= BIT(mac_type_bit[i]); + uses_usxgmii = true; + break; - // TODO: Set up RTL9300_SMI_10GPHY_POLLING_SEL_0 for Aquantia PHYs on e.g. XGS 1250 + case PHY_INTERFACE_MODE_QSGMII: + private_poll_mask |= BIT(i); + v |= 3 << mac_type_bit[i]; + break; + default: + break; + } + } + sw_w32(v, RTL930X_SMI_MAC_TYPE_CTRL); + + // Set the private polling mask for all Realtek PHYs (i.e. not the 10GBit Aquantia ones) + sw_w32(private_poll_mask, RTL930X_SMI_PRVTE_POLLING_CTRL); + + /* The following magic values are found in the port configuration, they seem to + * define different ways of polling a PHY. The below is for the Aquantia PHYs of + * the XGS1250 and the RTL8226 of the XGS1210 */ + if (uses_usxgmii) { + sw_w32(0x01010000, RTL930X_SMI_10GPHY_POLLING_REG0_CFG); + sw_w32(0x01E7C400, RTL930X_SMI_10GPHY_POLLING_REG9_CFG); + sw_w32(0x01E7E820, RTL930X_SMI_10GPHY_POLLING_REG10_CFG); + } + if (uses_hisgmii) { + sw_w32(0x011FA400, RTL930X_SMI_10GPHY_POLLING_REG0_CFG); + sw_w32(0x013FA412, RTL930X_SMI_10GPHY_POLLING_REG9_CFG); + sw_w32(0x017FA414, RTL930X_SMI_10GPHY_POLLING_REG10_CFG); + } + + pr_debug("%s: RTL930X_SMI_GLB_CTRL %08x\n", __func__, + sw_r32(RTL930X_SMI_GLB_CTRL)); + pr_debug("%s: RTL930X_SMI_PORT0_15_POLLING_SEL %08x\n", __func__, + sw_r32(RTL930X_SMI_PORT0_15_POLLING_SEL)); + pr_debug("%s: RTL930X_SMI_PORT16_27_POLLING_SEL %08x\n", __func__, + sw_r32(RTL930X_SMI_PORT16_27_POLLING_SEL)); + pr_debug("%s: RTL930X_SMI_MAC_TYPE_CTRL %08x\n", __func__, + sw_r32(RTL930X_SMI_MAC_TYPE_CTRL)); + pr_debug("%s: RTL930X_SMI_10GPHY_POLLING_REG0_CFG %08x\n", __func__, + sw_r32(RTL930X_SMI_10GPHY_POLLING_REG0_CFG)); + pr_debug("%s: RTL930X_SMI_10GPHY_POLLING_REG9_CFG %08x\n", __func__, + sw_r32(RTL930X_SMI_10GPHY_POLLING_REG9_CFG)); + pr_debug("%s: RTL930X_SMI_10GPHY_POLLING_REG10_CFG %08x\n", __func__, + sw_r32(RTL930X_SMI_10GPHY_POLLING_REG10_CFG)); + pr_debug("%s: RTL930X_SMI_PRVTE_POLLING_CTRL %08x\n", __func__, + sw_r32(RTL930X_SMI_PRVTE_POLLING_CTRL)); return 0; } @@ -2018,6 +2078,23 @@ static int rtl838x_mdio_init(struct rtl838x_eth_priv *priv) } } + dn = of_find_compatible_node(NULL, NULL, "realtek,rtl83xx-switch"); + if (!dn) { + dev_err(&priv->pdev->dev, "No RTL switch node in DTS\n"); + return -ENODEV; + } + + for_each_node_by_name(dn, "port") { + if (of_property_read_u32(dn, "reg", &pn)) + continue; + pr_info("%s Looking at port %d\n", __func__, pn); + if (pn > priv->cpu_port) + continue; + if (of_get_phy_mode(dn, &priv->interfaces[pn])) + priv->interfaces[pn] = PHY_INTERFACE_MODE_NA; + pr_info("%s phy mode of port %d is %s\n", __func__, pn, phy_modes(priv->interfaces[pn])); + } + snprintf(priv->mii_bus->id, MII_BUS_ID_SIZE, "%pOFn", mii_np); ret = of_mdiobus_register(priv->mii_bus, mii_np); @@ -2322,6 +2399,7 @@ static int __init rtl838x_eth_probe(struct platform_device *pdev) phylink = phylink_create(&priv->phylink_config, pdev->dev.fwnode, phy_mode, &rtl838x_phylink_ops); + if (IS_ERR(phylink)) { err = PTR_ERR(phylink); goto err_free; diff --git a/target/linux/realtek/files-5.10/drivers/net/ethernet/rtl838x_eth.h b/target/linux/realtek/files-5.10/drivers/net/ethernet/rtl838x_eth.h index 223b42fa24..6013de6c73 100644 --- a/target/linux/realtek/files-5.10/drivers/net/ethernet/rtl838x_eth.h +++ b/target/linux/realtek/files-5.10/drivers/net/ethernet/rtl838x_eth.h @@ -194,6 +194,11 @@ #define RTL930X_SMI_PORT0_15_POLLING_SEL (0xCA08) #define RTL930X_SMI_PORT16_27_POLLING_SEL (0xCA0C) +#define RTL930X_SMI_10GPHY_POLLING_REG0_CFG (0xCBB4) +#define RTL930X_SMI_10GPHY_POLLING_REG9_CFG (0xCBB8) +#define RTL930X_SMI_10GPHY_POLLING_REG10_CFG (0xCBBC) +#define RTL930X_SMI_PRVTE_POLLING_CTRL (0xCA10) + /* Registers of the internal Serdes of the 8390 */ #define RTL839X_SDS12_13_XSG0 (0xB800) @@ -290,7 +295,11 @@ inline u32 rtl839x_get_mac_link_sts(int p) inline u32 rtl930x_get_mac_link_sts(int port) { - return (sw_r32(RTL930X_MAC_LINK_STS) & BIT(port)); + u32 link = sw_r32(RTL930X_MAC_LINK_STS); + + link = sw_r32(RTL930X_MAC_LINK_STS); + pr_info("%s link state is %08x\n", __func__, link); + return link & BIT(port); } inline u32 rtl931x_get_mac_link_sts(int p)