From: Sven Eckelmann Date: Wed, 9 Aug 2017 11:52:07 +0000 (+0200) Subject: ipq40xx: add support for OpenMesh A62 X-Git-Tag: v18.06.0-rc1~340 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=0b204902075157dbb002ea04f41a5b1a4fbe848c;p=openwrt%2Fstaging%2Fxback.git ipq40xx: add support for OpenMesh A62 * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + 802.3at POE+ - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 18-24V passive POE (mode B) * powered only via POE The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. The initramfs image can be started using setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)' tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb set fdt_high 0x85000000 bootm 0x84000000 Signed-off-by: Sven Eckelmann --- diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx index 4eae506fb1..d475e56629 100644 --- a/package/boot/uboot-envtools/files/ipq40xx +++ b/package/boot/uboot-envtools/files/ipq40xx @@ -31,7 +31,8 @@ ubootenv_mtdinfo () { } case "$board" in -openmesh,a42) +openmesh,a42 |\ +openmesh,a62) ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000" ;; esac diff --git a/scripts/om-fwupgradecfg-gen.sh b/scripts/om-fwupgradecfg-gen.sh index 38e8e3ff3f..dad70b2ea0 100755 --- a/scripts/om-fwupgradecfg-gen.sh +++ b/scripts/om-fwupgradecfg-gen.sh @@ -7,7 +7,7 @@ # usage() { - echo "Usage: $0 " + echo "Usage: $0 " rm -f $CFG_OUT exit 1 } @@ -44,6 +44,14 @@ case $CE_TYPE in SIZE_FACTOR=1024 SIZE_FORMAT="0x%08x" ;; + A62) + MAX_PART_SIZE=15552 + KERNEL_FLASH_ADDR=0x1a0000 + FLASH_BS=65536 + MD5_SKIP_BLOCKS=4 + SIZE_FACTOR=1024 + SIZE_FORMAT="0x%08x" + ;; *) echo "Error - unsupported ce type: $CE_TYPE" exit 1 diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index ade1b05458..cbccbf92ef 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -38,7 +38,8 @@ glinet,gl-b1300) ucidef_add_switch "switch0" \ "0u@eth0" "3:lan" "4:lan" ;; -openmesh,a42) +openmesh,a42 |\ +openmesh,a62) ucidef_set_interfaces_lan_wan "eth1" "eth0" ;; meraki,mr33 |\ diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 0a5780cbf0..1eb93ba41d 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -110,6 +110,13 @@ case "$FIRMWARE" in ;; esac ;; +"ath10k/pre-cal-pci-0000:01:00.0.bin") + case "$board" in + openmesh,a62) + ath10kcal_extract "0:ART" 36864 12064 + ;; + esac + ;; "ath10k/pre-cal-ahb-a000000.wifi.bin") case "$board" in 8dev,jalapeno |\ @@ -135,7 +142,8 @@ case "$FIRMWARE" in ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 0) ;; compex,wpj428 |\ - openmesh,a42) + openmesh,a42 |\ + openmesh,a62) ath10kcal_extract "0:ART" 4096 12064 ;; esac @@ -165,7 +173,8 @@ case "$FIRMWARE" in ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 12) ;; compex,wpj428 |\ - openmesh,a42) + openmesh,a42 |\ + openmesh,a62) ath10kcal_extract "0:ART" 20480 12064 ;; esac diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/openmesh.sh b/target/linux/ipq40xx/base-files/lib/upgrade/openmesh.sh index 71ab247ead..f7aed7c9b6 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/openmesh.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/openmesh.sh @@ -47,6 +47,9 @@ platform_do_upgrade_openmesh() { openmesh,a42) primary_kernel_mtd=8 ;; + openmesh,a62) + primary_kernel_mtd=10 + ;; *) echo "failed to detect primary kernel mtd partition for board" return 1 diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 5493c47b63..4096e127ea 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -39,7 +39,8 @@ platform_do_upgrade() { CI_KERNPART="linux" nand_do_upgrade "$1" ;; - openmesh,a42) + openmesh,a42 |\ + openmesh,a62) PART_NAME="inactive" platform_do_upgrade_openmesh "$ARGV" ;; diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-a62.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-a62.dts new file mode 100644 index 0000000000..dd6d6bd775 --- /dev/null +++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-a62.dts @@ -0,0 +1,240 @@ +/* Copyright (c) 2015, The Linux Foundation. All rights reserved. + * Copyright (c) 2017-2018, Sven Eckelmann + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + * + */ + +#include "qcom-ipq4019.dtsi" +#include "qcom-ipq4019-bus.dtsi" +#include +#include +#include + +/ { + model = "OpenMesh A62"; + compatible = "openmesh,a62", "qcom,ipq4019"; + + soc { + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2: usb2@60f8800 { + status = "okay"; + }; + + serial@78af000 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + switch_lan_bmp = <0x10>; + switch_wan_bmp = <0x20>; + + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + gpio-leds { + compatible = "gpio-leds"; + + red { + label = "a62:red:status"; + gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-off"; + }; + + power: green { + label = "a62:green:status"; + gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>; + }; + + blue { + label = "a62:blue:status"; + gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-off"; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&tlmm 59 GPIO_ACTIVE_LOW>; + hw_algo = "toggle"; + /* hw_margin_ms is actually 300s but driver limits it to 60s */ + hw_margin_ms = <60000>; + always-running; + }; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pin { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + pin_cs { + function = "gpio"; + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + enable-usb-power { + gpio-hog; + gpios = <58 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "enable USB2 power"; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&spi_0 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + /* partitions are passed via bootloader */ + }; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac0 { + qcom,phy_mdio_addr = <3>; + qcom,poll_required = <1>; + qcom,forced_speed = <1000>; + qcom,forced_duplex = <1>; + vlan_tag = <1 0x10>; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&pcie0 { + status = "okay"; + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + ath10k@0,0 { + compatible = "qcom,ath10k"; + status = "okay"; + reg = <0 0 0 0 0>; + device_type = "pci"; + qcom,ath10k-calibration-variant = "OM-A62"; + }; + }; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "OM-A62"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "OM-A62"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 558f5529a7..be396f92da 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -160,6 +160,22 @@ define Device/openmesh_a42 endef TARGET_DEVICES += openmesh_a42 +define Device/openmesh_a62 + $(call Device/FitImageLzma) + DEVICE_DTS := qcom-ipq4019-a62 + DEVICE_DTS_CONFIG := config@om.a62 + BLOCKSIZE := 64k + DEVICE_TITLE := OpenMesh A62 + KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE) + IMAGE_SIZE := 15552k + IMAGES = factory.bin sysupgrade.bin + IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62 + IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata + DEVICE_PACKAGES := ath10k-firmware-qca9888 uboot-envtools +endef + +TARGET_DEVICES += openmesh_a62 + define Device/qcom_ap-dk01.1-c1 DEVICE_TITLE := QCA AP-DK01.1-C1 BOARD_NAME := ap-dk01.1-c1 diff --git a/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch index 99417d3e36..5b9317eb0e 100644 --- a/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -697,7 +697,17 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -697,7 +697,18 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -21,6 +21,7 @@ Signed-off-by: John Crispin + qcom-ipq4018-jalapeno.dtb \ + qcom-ipq4018-rt-ac58u.dtb \ qcom-ipq4019-ap.dk01.1-c1.dtb \ ++ qcom-ipq4019-a62.dtb \ + qcom-ipq4019-ap.dk04.1-c1.dtb \ + qcom-ipq4028-wpj428.dtb \ + qcom-ipq4029-gl-b1300.dtb \