From: Maxim Anisimov Date: Fri, 8 Sep 2017 09:39:17 +0000 (+0300) Subject: ramips: add support for TP-Link Archer C20 v1 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=161a3be5adb21135eb75da81247fa5e04b6ea676;p=openwrt%2Fstaging%2Fblogic.git ramips: add support for TP-Link Archer C20 v1 TP-Link Archer C20 v1 is a router with 5-port FE switch and non-detachable antennas. It's very similiar to TP-Link Archer C50. Also it's based on MediaTek MT7620A+MT7610EN. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 8x LED (GPIO-controlled*), 2x button, power input switch - 1 x USB 2.0 port * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the blue part of the LED. * MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't work. Factory image notes: These devices use version 3 of TP-Link header, fortunately without RSA signature (at least in case of devices sold in Europe). The difference lays in the requirement for a non-zero value in "Additional Hardware Version" field. Ideally, it should match the value stored in vendor firmware header on device. We are able to prepare factory firwmare file which is accepted and (almost) correctly flashed from the vendor GUI. As it turned out, it accepts files without U-Boot image with second header at the beginning but due to some kind of bug in upgrade routine, flashed image gets corrupted before it's written to flash. So, to flash this device we must to prepare image using original firmware from tp-link site with uboot. Flash instruction: Until (if at all) TP-Link fixes described problem, the only way to flash LEDE image in these devices is to use tftp recovery mode in U-Boot. There are two ways to flash the device to LEDE: 1) Using tftp mode with UART connection and original LEDE image - Place lede-ramips-mt7620-ArcherC20-squashfs-factory.bin in tftp server directory - Configure PC with static IP 192.168.0.66/24 and tftp server. - Connect PC with one of LAN ports, power up the router and press key "4" to access U-Boot CLI. - Use the following commands to update the device to LEDE: setenv serverip 192.168.0.66 tftp 0x80060000 lede-ramips-mt7620-ArcherC20-squashfs-factory.bin erase tplink 0x20000 0x7a0000 cp.b 0x80060000 0x20000 0x7a0000 reset - After that the device will reboot and boot to LEDE 2) Using tftp mode without UART connection but require some manipulations with target image - Download and unpack TP-Link Archer C20 v1 firmware from original web site - Split uboot.bin from original firmware by this command (example): dd if=Archer_C20v1_0.9.1_4.0_up_boot(160427)_2016-04-27_13.53.59.bin of=uboot.bin bs=512 count=256 skip=1 - Create ArcherC20V1_tp_recovery.bin using this command: cat uboot.bin lede-ramips-mt7620-ArcherC20-squashfs-factory.bin > ArcherC20V1_tp_recovery.bin - Place ArcherC20V1_tp_recovery.bin in tftp server directory. - Configure PC with static IP 192.168.0.66/24 and tftp server. - Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. - Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov --- diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index f6a7bac81ad4..a0baa6102710 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -86,6 +86,12 @@ c108) ucidef_set_led_netdev "lan" "lan" "$board:green:lan" "eth0" ucidef_set_led_netdev "modem" "modem" "$board:green:modem" "wwan0" ;; +c20) + ucidef_set_led_switch "lan" "lan" "$board:blue:lan" "switch0" "0x1e" + ucidef_set_led_switch "wan" "wan" "$board:blue:wan" "switch0" "0x01" + set_usb_led "$board:blue:usb" + ucidef_set_led_netdev "wlan2g" "wlan2g" "$board:blue:wlan2g" "wlan0" + ;; c20i) ucidef_set_led_switch "lan" "lan" "$board:blue:lan" "switch0" "0x1e" ucidef_set_led_switch "wan" "wan" "$board:blue:wan" "switch0" "0x01" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 6f05259467eb..862e99b0bbd2 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -184,6 +184,7 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0" ;; + c20|\ c50) ucidef_add_switch "switch0" \ "1:lan:3" "2:lan:4" "3:lan:1" "4:lan:2" "0:wan" "6@eth0" diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index 16c83f2d3f92..0345f1e8bf77 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -119,6 +119,7 @@ get_status_led() { w502u) status_led="$board:blue:wps" ;; + c20|\ d240|\ dap-1350|\ na930|\ diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index d0055d422b73..d0b9bb126279 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -88,6 +88,9 @@ ramips_board_detect() { *"C108") name="c108" ;; + *"C20") + name="c20" + ;; *"C20i") name="c20i" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index 09a7dae39460..e08c45d8dbfc 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -230,6 +230,7 @@ platform_check_image() { } return 0 ;; + c20|\ c20i|\ c50|\ mr200|\ diff --git a/target/linux/ramips/dts/ArcherC20.dts b/target/linux/ramips/dts/ArcherC20.dts new file mode 100644 index 000000000000..a0e7c61b5b18 --- /dev/null +++ b/target/linux/ramips/dts/ArcherC20.dts @@ -0,0 +1,189 @@ +/dts-v1/; + +#include "mt7620a.dtsi" + +#include +#include + +/ { + compatible = "tplink,c20", "ralink,mt7620a-soc"; + model = "TP-Link Archer C20"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + gpio-leds { + compatible = "gpio-leds"; + + lan { + label = "c20:blue:lan"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + }; + + power { + label = "c20:blue:power"; + gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; + }; + + usb { + label = "c20:blue:usb"; + gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; + }; + + wan { + label = "c20:blue:wan"; + gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + }; + + wan_orange { + label = "c20:orange:wan"; + gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; + }; + + wlan5g { + label = "c20:blue:wlan5g"; + gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + label = "c20:blue:wlan2g"; + gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "c20:blue:wps"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + rfkill { + label = "rfkill"; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; }; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&gpio3 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x20000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x7a0000>; + }; + + partition@7c0000 { + label = "config"; + reg = <0x7c0000 0x10000>; + read-only; + }; + + rom: partition@7d0000 { + label = "rom"; + reg = <0x7d0000 0x10000>; + read-only; + }; + + partition@7e0000 { + label = "romfile"; + reg = <0x7e0000 0x10000>; + read-only; + }; + + radio: partition@7f0000 { + label = "radio"; + reg = <0x7f0000 0x10000>; + read-only; + }; + }; +}; + +&pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "i2c", "uartf", "wled", "ephy", "spi refclk", "wdt"; + ralink,function = "gpio"; + }; + + pa { + ralink,group = "pa"; + ralink,function = "pa"; + }; + }; +}; + +ðernet { + pinctrl-names = "default"; + mtd-mac-address = <&rom 0xf100>; + mediatek,portmap = "wllll"; + }; + +&ehci { + status = "okay"; +}; + +&ohci { + status = "okay"; +}; + +&gsw { + mediatek,port4 = "ephy"; +}; + +&wmac { + ralink,mtd-eeprom = <&radio 0>; + mtd-mac-address = <&rom 0xf100>; + mtd-mac-address-increment = <(-2)>; +}; + +&pcie { + status = "okay"; + + pcie-bridge { + mt76@0,0 { + reg = <0x0000 0 0 0 0>; + device_type = "pci"; + mediatek,mtd-eeprom = <&radio 32768>; + ieee80211-freq-limit = <5000000 6000000>; + mtd-mac-address = <&rom 0xf100>; + mtd-mac-address-increment = <(-1)>; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk index 6d2533d349ba..f964b3e0821c 100644 --- a/target/linux/ramips/image/mt7620.mk +++ b/target/linux/ramips/image/mt7620.mk @@ -32,6 +32,17 @@ define Device/Archer IMAGE/sysupgrade.bin := tplink-v2-image -s | append-metadata endef +define Device/ArcherC20 + $(Device/Archer) + DTS := ArcherC20 + SUPPORTED_DEVICES := c20 + TPLINK_BOARD_ID := ArcherC20 + IMAGES += factory.bin + DEVICE_TITLE := TP-Link ArcherC20 + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport +endef +TARGET_DEVICES += ArcherC20 + define Device/ArcherC20i $(Device/Archer) DTS := ArcherC20i diff --git a/tools/firmware-utils/src/mktplinkfw2.c b/tools/firmware-utils/src/mktplinkfw2.c index 7d094774c85d..6ef51db55b9f 100644 --- a/tools/firmware-utils/src/mktplinkfw2.c +++ b/tools/firmware-utils/src/mktplinkfw2.c @@ -180,6 +180,14 @@ static struct board_info boards[] = { .hw_id = 0x89800001, .hw_rev = 14, .layout_id = "8Mltq", + }, { + .id = "ArcherC20", + .hw_id = 0xc2000001, + .hw_rev = 0x44, + .hw_ver_add = 0x1, + .layout_id = "8Mmtk", + .hdr_ver = 3, + .flags = FLAG_LE_KERNEL_LA_EP }, { .id = "ArcherC20i", .hw_id = 0xc2000001,