From: Otavio Salvador Date: Thu, 31 Jan 2019 12:46:01 +0000 (-0200) Subject: regulator: rk808: Fix BUCK1/2 voltages on rk805 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=2b679ca1136129b0601f3d439965f83bd33d9eda;p=openwrt%2Fstaging%2Fblogic.git regulator: rk808: Fix BUCK1/2 voltages on rk805 RK805 has the following voltage range for the BUCK1 and BUCK2 regulators: From 0.7125V to 1.45V in 12.5mV steps, 1.8V, 2V, 2.2V and 2.3V , which corresponds to the following values as per the RK805 datasheet: 000 000: 0.7125V 000 001: 0.725V …… 111 011: 1.45V 111 100: 1.8V 111 101: 2.0V 111 110: 2.2V 111 111: 2.3V This means that the voltage range is not linear and so RK805 can not reuse the same regulator_ops structure from RK808. Fix it by creating a list with the correct supported voltage values for RK805 BUCK1 and BUCK2 regulators. Tested on a rv1108-elgin-r1 board that now correctly reports a BUCK2 voltage of 2.2V instead of the unsupported value of 1.4875V. Fixes: c4e0d344c1f0 ("regulator: rk808: Add regulator driver for RK805") Signed-off-by: Otavio Salvador Signed-off-by: Mark Brown --- diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c index 08578f6d737d..79e79cdd503b 100644 --- a/drivers/regulator/rk808-regulator.c +++ b/drivers/regulator/rk808-regulator.c @@ -289,6 +289,21 @@ static int rk808_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay) RK808_RAMP_RATE_MASK, ramp_value); } +static int rk805_set_suspend_voltage(struct regulator_dev *rdev, int uv) +{ + unsigned int reg; + int sel = regulator_map_voltage_ascend(rdev, uv, uv); + + if (sel < 0) + return -EINVAL; + + reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET; + + return regmap_update_bits(rdev->regmap, reg, + rdev->desc->vsel_mask, + sel); +} + static int rk808_set_suspend_voltage(struct regulator_dev *rdev, int uv) { unsigned int reg; @@ -384,6 +399,19 @@ static const struct regulator_ops rk805_switch_ops = { .set_suspend_disable = rk805_set_suspend_disable, }; +static struct regulator_ops rk805_buck1_2_ops = { + .list_voltage = regulator_list_voltage_table, + .map_voltage = regulator_map_voltage_ascend, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .set_suspend_voltage = rk805_set_suspend_voltage, + .set_suspend_enable = rk805_set_suspend_enable, + .set_suspend_disable = rk805_set_suspend_disable, +}; + static const struct regulator_ops rk808_buck1_2_ops = { .list_voltage = regulator_list_voltage_linear, .map_voltage = regulator_map_voltage_linear, @@ -433,6 +461,17 @@ static const struct regulator_ops rk808_switch_ops = { .set_suspend_disable = rk808_set_suspend_disable, }; +static const int rk805_buck_1_2_voltages[] = { + 712500, 725000, 737500, 750000, 762500, 775000, 787500, 800000, + 812500, 825000, 837500, 850000, 862500, 875000, 887500, 900000, + 912500, 925000, 937500, 950000, 962500, 975000, 987500, 1000000, + 1012500, 1025000, 1037500, 1050000, 1062500, 1075000, 1087500, 1100000, + 1112500, 1125000, 1137500, 1150000, 1162500, 1175000, 1187500, 1200000, + 1212500, 1225000, 1237500, 1250000, 1262500, 1275000, 1287500, 1300000, + 1312500, 1325000, 1337500, 1350000, 1362500, 1375000, 1387500, 1400000, + 1412500, 1425000, 1437500, 1450000, 1800000, 2000000, 2200000, 2300000, +}; + static const struct regulator_desc rk805_reg[] = { { .name = "DCDC_REG1", @@ -440,11 +479,10 @@ static const struct regulator_desc rk805_reg[] = { .of_match = of_match_ptr("DCDC_REG1"), .regulators_node = of_match_ptr("regulators"), .id = RK805_ID_DCDC1, - .ops = &rk805_reg_ops, + .ops = &rk805_buck1_2_ops, .type = REGULATOR_VOLTAGE, - .min_uV = 712500, - .uV_step = 12500, - .n_voltages = 64, + .n_voltages = ARRAY_SIZE(rk805_buck_1_2_voltages), + .volt_table = rk805_buck_1_2_voltages, .vsel_reg = RK805_BUCK1_ON_VSEL_REG, .vsel_mask = RK818_BUCK_VSEL_MASK, .enable_reg = RK805_DCDC_EN_REG, @@ -456,11 +494,10 @@ static const struct regulator_desc rk805_reg[] = { .of_match = of_match_ptr("DCDC_REG2"), .regulators_node = of_match_ptr("regulators"), .id = RK805_ID_DCDC2, - .ops = &rk805_reg_ops, + .ops = &rk805_buck1_2_ops, .type = REGULATOR_VOLTAGE, - .min_uV = 712500, - .uV_step = 12500, - .n_voltages = 64, + .n_voltages = ARRAY_SIZE(rk805_buck_1_2_voltages), + .volt_table = rk805_buck_1_2_voltages, .vsel_reg = RK805_BUCK2_ON_VSEL_REG, .vsel_mask = RK818_BUCK_VSEL_MASK, .enable_reg = RK805_DCDC_EN_REG,