From: Valentín Kivachuk Date: Thu, 29 Nov 2018 23:13:53 +0000 (+0100) Subject: ramips: add support for MTC Wireless Router WR1201 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=30a7ab8f61c8a5f1a4428f8c7cf9a1d6a12b096b;p=openwrt%2Fstaging%2Fzorun.git ramips: add support for MTC Wireless Router WR1201 MTC Wireless Router WR1201 is the OEM name of the board. It is also sold rebranded as STRONG Dual Band Gigabit Router 1200. Specification: - SoC: MediaTek MT7621A (880 MHz) - Flash: 16 MiB - RAM: 128 MiB - Wireless: 2.4Ghz(MT7602EN) and 5Ghz (MT7612EN) - Ethernet speed: 10/100/1000 - Ethernet ports: 4+1 - 1x USB 3.0 - 1x microSD reader - Serial baud rate of Bootloader and factory firmware: 57600 The OEM webinterface writes only as much bytes as listed in the uImage header field to the flash. Also, the OEM webinterface evaluates the name field of uImage header before flashing (the string "WR1201_8_128") To flash via webinterface, is mandatory to use first initramfs.bin and after (from the OpenWrt) the sysupgrade.bin Some notes: - Some microSD will not work: mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising SDIO card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising MMC card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising SDIO card mtk-sd 1e130000.sdhci: card claims to support voltages below defined range mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising MMC card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising SDIO card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising MMC card Signed-off-by: Valentín Kivachuk --- diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 4330254c8f..b2c69d4b59 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -236,6 +236,9 @@ mr200) ucidef_set_led_netdev "wan" "wan" "$boardname:white:wan" "usb0" set_wifi_led "$boardname:white:wlan" ;; +mtc,wr1201) + ucidef_set_led_switch "eth_link" "LAN link" "$boardname:green:eth_link" "switch0" "0x0f" + ;; mzk-ex750np) set_wifi_led "$boardname:red:wifi" ;; diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 0d8855c324..3af836a6f3 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -102,6 +102,7 @@ ramips_setup_interfaces() miwifi-nano|\ mt7621|\ mt7628|\ + mtc,wr1201|\ mzk-750dhp|\ mzk-w300nh2|\ netgear,r6120|\ diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index e28f066658..120cf8322a 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -110,6 +110,7 @@ platform_check_image() { mpr-a2|\ mr-102n|\ mt7628|\ + mtc,wr1201|\ mzk-750dhp|\ mzk-dp150n|\ mzk-ex300np|\ diff --git a/target/linux/ramips/dts/WR1201.dts b/target/linux/ramips/dts/WR1201.dts new file mode 100644 index 0000000000..be20717499 --- /dev/null +++ b/target/linux/ramips/dts/WR1201.dts @@ -0,0 +1,159 @@ +/dts-v1/; + +#include "mt7621.dtsi" + +#include +#include + +/ { + compatible = "mtc,wr1201", "mediatek,mt7621-soc"; + model = "MTC Wireless Router WR1201"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,57600"; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_power: power { + label = "wr1201:green:power"; + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; + }; + + usb { + label = "wr1201:green:usb"; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; + trigger-sources = <&xhci_ehci_port1>, <&ehci_port2>; + linux,default-trigger = "usbport"; + }; + + eth_link { + label = "wr1201:green:eth_link"; + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "wr1201:green:wps"; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + m25p,chunked-io = <32>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Bootloader"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "Config"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "Factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0xfa0000>; + }; + + partition@ff0000 { + label = "Second_Config"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; +}; + +ðernet { + mtd-mac-address = <&factory 0x4>; +}; + +&sdhci { + status = "okay"; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + ieee80211-freq-limit = <5000000 6000000>; + + led { + led-sources = <2>; + led-active-low; + }; + }; +}; + +&pcie1 { + wifi@0,0 { + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0000>; + ieee80211-freq-limit = <2400000 2500000>; + + led { + led-sources = <2>; + led-active-low; + }; + }; +}; + + +&pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "rgmii2"; + ralink,function = "gpio"; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index d0cf51f7e9..6a04cd0e38 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -47,6 +47,19 @@ define Build/iodata-factory fi endef +# The OEM webinterface expects an kernel with initramfs which has the uImage +# header field ih_name. +# We don't wan't to set the header name field for the kernel include in the +# sysupgrade image as well, as this image shouldn't be accepted by the OEM +# webinterface. It will soft-brick the board. +define Build/wr1201-factory-header + mkimage -A $(LINUX_KARCH) \ + -O linux -T kernel \ + -C lzma -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \ + -n 'WR1201_8_128' -d $@ $@.new + mv $@.new $@ +endef + define Build/ubnt-erx-factory-image if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \ echo '21001:6' > $(1).compat; \ @@ -317,6 +330,16 @@ define Device/mikrotik_rbm11g endef TARGET_DEVICES += mikrotik_rbm11g +define Device/mtc_wr1201 + DTS := WR1201 + IMAGE_SIZE := 16000k + DEVICE_TITLE := MTC Wireless Router WR1201 + KERNEL_INITRAMFS := $(KERNEL_DTB) | wr1201-factory-header + DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \ + kmod-usb-ledtrig-usbport wpad-basic +endef +TARGET_DEVICES += mtc_wr1201 + define Device/re350-v1 DTS := RE350 DEVICE_TITLE := TP-LINK RE350 v1