From: Daniel Golle Date: Thu, 28 Jul 2022 11:40:12 +0000 (+0200) Subject: mac80211: rt2x00: experimental improvements for MT7620 wifi X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=31a6605de04218e1c04bd5c2436c24d7d1c07506;p=openwrt%2Fstaging%2Fblocktrron.git mac80211: rt2x00: experimental improvements for MT7620 wifi Serge Vasilugin reports: To improve mt7620 built-in wifi performance some changes: 1. Correct BW20/BW40 switching (see comments with mark (1)) 2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531 3. Set bbp66 for all chains. 4. US_CYC_CNT init based on Programming guide, default value was 33 (pci), set chipset bus clock with fallback to cpu clock/3. 5. Don't overwrite default values for mt7620. 6. Correct some typos. 7. Add support for external LNA: a) RF and BBP regs never be corrected for this mode b) eLNA is driven the same way as ePA with mt7620's pin PA but vendor driver explicitly pin PA to gpio mode (for forrect calibration?) so I'm not sure that request for pa_pin in dts-file will be enough First 5 changes (really 2) improve performance for boards w/o eLNA/ePA. Changes 7 add support for eLNA Configuration w/o eLAN/ePA and with eLNA show results tx/rx (from router point of view) for each stream: 35-40/30-35 Mbps for HT20 65-70/60-65 Mbps for HT40 Yes. Max results for 2T2R client is 140-145/135-140 with peaks 160/150, It correspond to mediatek driver results. Boards with ePA untested. Reported-by: Serge Vasilugin Signed-off-by: Daniel Golle --- diff --git a/package/kernel/mac80211/patches/rt2x00/992-rt2x00-more-fixes.patch b/package/kernel/mac80211/patches/rt2x00/992-rt2x00-more-fixes.patch new file mode 100644 index 0000000000..2ad6219014 --- /dev/null +++ b/package/kernel/mac80211/patches/rt2x00/992-rt2x00-more-fixes.patch @@ -0,0 +1,423 @@ +From: Daniel Golle +Date: Mon, 12 Sep 2022 21:33:13 +0100 +Subject: [PATCH] rt2x00: various experimental fixes for MT7620 + +Serge Vasilugin reports: + +To improve mt7620 built-in wifi performance some changes: +1. Correct BW20/BW40 switching (see comments with mark see commets with mark (1)) +2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see + https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531 +3. Set bbp66 for all chains. +4. US_CYC_CNT init based on Programming guide, default value was 33 (pci), + set chipset bus clock with fallback to cpu clock/3. +5. Don't overwrite default values for mt7620. +6. Correct some typos. +7. Add support for external LNA: + a) RF and BBP regs never be corrected for this mode + b) eLNA is driven the same way as ePA with mt7620's pin PA + but vendor driver explicitly pin PA to gpio mode (for forrect calibration?) + so I'm not sure that request for pa_pin in dts-file will be enough + +First 5 changes (really 2) improve performance for boards w/o eLNA/ePA. +Changes 7 add support for eLNA + +Configuration w/o eLAN/ePA and with eLNA show results +tx/rx (from router point of view) for each stream: + 35-40/30-35 Mbps for HT20 + 65-70/60-65 Mbps for HT40 + +Yes. Max results for 2T2R client is 140-145/135-140 +with peaks 160/150, It correspond to mediatek driver results. +Boards with ePA untested. + +Reported-by: Serge Vasilugin +Signed-off-by: Daniel Golle +--- +--- a/drivers/net/wireless/ralink/rt2x00/rt2800lib.c ++++ b/drivers/net/wireless/ralink/rt2x00/rt2800lib.c +@@ -137,6 +137,26 @@ static u8 rt2800_bbp_read(struct rt2x00_ + + return value; + } ++//serge: move here for use in test ++static void rt2800_bbp_glrt_write(struct rt2x00_dev *rt2x00dev, ++ const u8 reg, const u8 value) ++{ ++ rt2800_bbp_write(rt2x00dev, 195, reg); ++ rt2800_bbp_write(rt2x00dev, 196, value); ++} ++ ++static void rt2800_bbp_dcoc_write(struct rt2x00_dev *rt2x00dev, ++ const u8 reg, const u8 value) ++{ ++ rt2800_bbp_write(rt2x00dev, 158, reg); ++ rt2800_bbp_write(rt2x00dev, 159, value); ++} ++ ++static u8 rt2800_bbp_dcoc_read(struct rt2x00_dev *rt2x00dev, const u8 reg) ++{ ++ rt2800_bbp_write(rt2x00dev, 158, reg); ++ return rt2800_bbp_read(rt2x00dev, 159); ++} + + static void rt2800_rfcsr_write(struct rt2x00_dev *rt2x00dev, + const unsigned int word, const u8 value) +@@ -284,6 +304,28 @@ static void rt2800_rf_write(struct rt2x0 + mutex_unlock(&rt2x00dev->csr_mutex); + } + ++void rt6352_enable_pa_pin(struct rt2x00_dev *rt2x00dev, int enable) ++{ ++ if (!rt2x00dev->pinctrl) ++ return; ++ ++ if (enable) { ++ if (!rt2x00dev->pins_default) { ++ rt2x00_warn(rt2x00dev, "cannot enable PA pin! no default pinctrl\n"); ++ return; ++ } ++ ++ pinctrl_select_state(rt2x00dev->pinctrl, rt2x00dev->pins_default); ++ } else { ++ if (!rt2x00dev->pins_pa_gpio) { ++ rt2x00_warn(rt2x00dev, "cannot disable PA pin! no pa_gpio pinctrl\n"); ++ return; ++ } ++ ++ pinctrl_select_state(rt2x00dev->pinctrl, rt2x00dev->pins_pa_gpio); ++ } ++} ++ + static const unsigned int rt2800_eeprom_map[EEPROM_WORD_COUNT] = { + [EEPROM_CHIP_ID] = 0x0000, + [EEPROM_VERSION] = 0x0001, +@@ -3801,6 +3843,20 @@ static void rt2800_config_channel_rf7620 + rfcsr |= tx_agc_fc; + rt2800_rfcsr_write_bank(rt2x00dev, 7, 59, rfcsr); + } ++ ++ if (conf_is_ht40(conf)) {//serge:skipped this step (1) ++ rt2800_bbp_write(rt2x00dev, 195, 141); ++ rt2800_bbp_write(rt2x00dev, 196, 0x10); ++ rt2800_bbp_write(rt2x00dev, 195, 157); ++ rt2800_bbp_write(rt2x00dev, 196, 0x2f); ++ //rt2800_bbp_write(rt2x00dev, 105, 0x3C); ++ } else { ++ rt2800_bbp_write(rt2x00dev, 195, 141); ++ rt2800_bbp_write(rt2x00dev, 196, 0x1a); ++ rt2800_bbp_write(rt2x00dev, 195, 157); ++ rt2800_bbp_write(rt2x00dev, 196, 0x40); ++ //rt2800_bbp_write(rt2x00dev, 105, 0x1C); ++ } + } + + static void rt2800_config_alc(struct rt2x00_dev *rt2x00dev, +@@ -4172,6 +4228,11 @@ static void rt2800_config_channel(struct + rt2800_bbp_write(rt2x00dev, 86, 0x46); + else + rt2800_bbp_write(rt2x00dev, 86, 0); ++ } else if (rt2x00_rt(rt2x00dev, RT6352)) {//serge: don't overwite bbp r86 (5) ++ rt2800_bbp_write(rt2x00dev, 62, 0x37 - rt2x00dev->lna_gain); ++ rt2800_bbp_write(rt2x00dev, 63, 0x37 - rt2x00dev->lna_gain); ++ rt2800_bbp_write(rt2x00dev, 64, 0x37 - rt2x00dev->lna_gain); ++ rt2800_bbp_write(rt2x00dev, 86, 0x38); + } else { + rt2800_bbp_write(rt2x00dev, 62, 0x37 - rt2x00dev->lna_gain); + rt2800_bbp_write(rt2x00dev, 63, 0x37 - rt2x00dev->lna_gain); +@@ -4377,7 +4438,8 @@ static void rt2800_config_channel(struct + reg = (rf->channel <= 14 ? 0x1c : 0x24) + 2*rt2x00dev->lna_gain; + rt2800_bbp_write_with_rx_chain(rt2x00dev, 66, reg); + +- rt2800_iq_calibrate(rt2x00dev, rf->channel); ++ if (!rt2x00_rt(rt2x00dev, RT6352))//serge: this function for rt5592 only, for rt6352 it switch off compensations (5) ++ rt2800_iq_calibrate(rt2x00dev, rf->channel); + } + + if (rt2x00_rt(rt2x00dev, RT6352)) { +@@ -4417,6 +4479,31 @@ static void rt2800_config_channel(struct + rt2800_register_write(rt2x00dev, TX1_RF_GAIN_ATTEN, + 0x6C6C6B6C); + } ++ ++ if (rt2x00_has_cap_external_lna_bg(rt2x00dev)) {//serge: for support eLNA (7a) ++ rt2x00_warn(rt2x00dev, "Correct RF/BBP for eLNA!\n"); ++ reg = rt2800_register_read(rt2x00dev, RF_CONTROL3); ++ reg |= 0x00000101; ++ rt2800_register_write(rt2x00dev, RF_CONTROL3, reg); ++ ++ reg = rt2800_register_read(rt2x00dev, RF_BYPASS3); ++ reg |= 0x00000101; ++ rt2800_register_write(rt2x00dev, RF_BYPASS3, reg); ++ ++ rt2800_rfcsr_write_chanreg(rt2x00dev, 14, 0x66); ++ rt2800_rfcsr_write_chanreg(rt2x00dev, 17, 0x20); ++ rt2800_rfcsr_write_chanreg(rt2x00dev, 18, 0x42); ++ rt2800_bbp_write(rt2x00dev, 75, 0x68);//serge: move bbp eLNA init here? ++ rt2800_bbp_write(rt2x00dev, 76, 0x4C); ++ rt2800_bbp_write(rt2x00dev, 79, 0x1C); ++ rt2800_bbp_write(rt2x00dev, 80, 0x0C); ++ rt2800_bbp_write(rt2x00dev, 82, 0xB6); ++ /* bank 0 RF reg 42 and glrt BBP reg 141 ++ will be set in config channel function ++ in dependence of channel and HT20/HT40 ++ so don't touch it ++ */ ++ } + } + + bbp = rt2800_bbp_read(rt2x00dev, 4); +@@ -4457,6 +4544,9 @@ static void rt2800_config_channel(struct + rt2x00_set_field8(&bbp, BBP49_UPDATE_FLAG, 0); + rt2800_bbp_write(rt2x00dev, 49, bbp); + } ++//serge:just print results after config channel - don't forget to remove nahren (c) <- this is copyright, not ref to comments :) ++ bbp = rt2800_bbp_dcoc_read(rt2x00dev, 0x03); ++ pr_info("BBP tx/rx compensation control=0x%02x\n", bbp); + } + + static int rt2800_get_gain_calibration_delta(struct rt2x00_dev *rt2x00dev) +@@ -5527,7 +5617,7 @@ void rt2800_vco_calibration(struct rt2x0 + } + rt2800_register_write(rt2x00dev, TX_PIN_CFG, tx_pin); + +- if (rt2x00_rt(rt2x00dev, RT6352)) { ++ if (rt2x00_rt(rt2x00dev, RT6352)) {//serge:remark - move all this code to rfcsr_6352 init? + if (rt2x00dev->default_ant.rx_chain_num == 1) { + rt2800_bbp_write(rt2x00dev, 91, 0x07); + rt2800_bbp_write(rt2x00dev, 95, 0x1A); +@@ -5695,7 +5785,8 @@ static inline void rt2800_set_vgc(struct + if (qual->vgc_level != vgc_level) { + if (rt2x00_rt(rt2x00dev, RT3572) || + rt2x00_rt(rt2x00dev, RT3593) || +- rt2x00_rt(rt2x00dev, RT3883)) { ++ rt2x00_rt(rt2x00dev, RT3883) || ++ rt2x00_rt(rt2x00dev, RT6352)) {//serge: rt6352 too (3) + rt2800_bbp_write_with_rx_chain(rt2x00dev, 66, + vgc_level); + } else if (rt2x00_rt(rt2x00dev, RT5592)) { +@@ -5930,7 +6021,7 @@ static int rt2800_init_registers(struct + 0x00550055); + } else { + rt2800_register_write(rt2x00dev, TX_SW_CFG0, 0x00000401); +- rt2800_register_write(rt2x00dev, TX_SW_CFG1, 0x000C0000); ++ rt2800_register_write(rt2x00dev, TX_SW_CFG1, 0x000C0001);//serge:was 0x000C0000 (2) + rt2800_register_write(rt2x00dev, TX_SW_CFG2, 0x00000000); + rt2800_register_write(rt2x00dev, TX_ALC_VGA3, 0x00000000); + rt2800_register_write(rt2x00dev, TX0_BB_GAIN_ATTEN, 0x0); +@@ -6195,6 +6286,29 @@ static int rt2800_init_registers(struct + reg = rt2800_register_read(rt2x00dev, US_CYC_CNT); + rt2x00_set_field32(®, US_CYC_CNT_CLOCK_CYCLE, 125); + rt2800_register_write(rt2x00dev, US_CYC_CNT, reg); ++ } else if (rt2x00_is_soc(rt2x00dev)) {//serge:which value correct? (4) ++ struct clk *clk = clk_get_sys("bus", NULL); ++ int rate; ++ ++ if (IS_ERR(clk)) { ++ rt2x00_warn(rt2x00dev, "system bus clock undefined\n"); ++ clk = clk_get_sys("cpu", NULL); ++ ++ if (IS_ERR(clk)) ++ rate = 125; ++ else { ++ rate = clk_get_rate(clk) / 3000000; ++ clk_put(clk); ++ } ++ } else { ++ rate = clk_get_rate(clk) / 1000000; ++ clk_put(clk); ++ } ++ ++ rt2x00_info(rt2x00dev, "set US_CYC=%dMHz\n", rate); ++ reg = rt2800_register_read(rt2x00dev, US_CYC_CNT); ++ rt2x00_set_field32(®, US_CYC_CNT_CLOCK_CYCLE, rate); ++ rt2800_register_write(rt2x00dev, US_CYC_CNT, reg); + } + + reg = rt2800_register_read(rt2x00dev, HT_FBK_CFG0); +@@ -6981,26 +7095,7 @@ static void rt2800_init_bbp_5592(struct + if (rt2x00_rt_rev_gte(rt2x00dev, RT5592, REV_RT5592C)) + rt2800_bbp_write(rt2x00dev, 103, 0xc0); + } +- +-static void rt2800_bbp_glrt_write(struct rt2x00_dev *rt2x00dev, +- const u8 reg, const u8 value) +-{ +- rt2800_bbp_write(rt2x00dev, 195, reg); +- rt2800_bbp_write(rt2x00dev, 196, value); +-} +- +-static void rt2800_bbp_dcoc_write(struct rt2x00_dev *rt2x00dev, +- const u8 reg, const u8 value) +-{ +- rt2800_bbp_write(rt2x00dev, 158, reg); +- rt2800_bbp_write(rt2x00dev, 159, value); +-} +- +-static u8 rt2800_bbp_dcoc_read(struct rt2x00_dev *rt2x00dev, const u8 reg) +-{ +- rt2800_bbp_write(rt2x00dev, 158, reg); +- return rt2800_bbp_read(rt2x00dev, 159); +-} ++//serge: move these function upper + + static void rt2800_init_bbp_6352(struct rt2x00_dev *rt2x00dev) + { +@@ -8635,7 +8730,7 @@ static void rt2800_r_calibration(struct + r_cal_code = (u8)rcalcode; + + rt2800_rfcsr_write_bank(rt2x00dev, 0, 7, r_cal_code); +- ++ pr_info("RF bank 0 reg 5=0x%02x\n", r_cal_code);//serge: just for info to compare with vendor driver + rt2800_bbp_write(rt2x00dev, 22, 0x0); + + bytevalue = rt2800_bbp_read(rt2x00dev, 21); +@@ -8693,7 +8788,7 @@ static void rt2800_rxdcoc_calibration(st + break; + } + +- saverfb5r4 = rt2800_rfcsr_read_bank(rt2x00dev, 5, 0); ++ saverfb5r4 = rt2800_rfcsr_read_bank(rt2x00dev, 5, 4);//serge: was 0 - typo? (6) + saverfb7r4 = rt2800_rfcsr_read_bank(rt2x00dev, 7, 4); + saverfb5r4 = saverfb5r4 & (~0x40); + saverfb7r4 = saverfb7r4 & (~0x40); +@@ -9022,13 +9117,15 @@ static void rt2800_rxiq_calibration(stru + rt2x00_info(rt2x00dev, "RXIQ G_imb=%d, Ph_rx=%d\n", g_imb, ph_rx); + + if ((ph_rx > 20) || (ph_rx < -20)) { ++ rt2x00_warn(rt2x00dev, "RXIQ calibration FAIL(ph_rx=%d out of [-20..20]", ph_rx);//serge:just to see value + ph_rx = 0; +- rt2x00_warn(rt2x00dev, "RXIQ calibration FAIL"); ++ //rt2x00_warn(rt2x00dev, "RXIQ calibration FAIL"); + } + + if ((g_imb > 12) || (g_imb < -12)) { ++ rt2x00_warn(rt2x00dev, "RXIQ calibration FAIL(g_imb=%d out of (-12..12]", g_imb);//serge:just to see the reason + g_imb = 0; +- rt2x00_warn(rt2x00dev, "RXIQ calibration FAIL"); ++ //rt2x00_warn(rt2x00dev, "RXIQ calibration FAIL"); + } + } + else { +@@ -9039,11 +9136,21 @@ static void rt2800_rxiq_calibration(stru + } + + if (ch_idx == 0) { ++ //serge: just to see values ++ pr_info("RXIQ RX0 g_imb (0x37, %2x) ph_rx (0x35, %2x)\n", ++ g_imb & 0x3f, ++ ph_rx & 0x3f ++ ); + rt2800_bbp_write(rt2x00dev, 158, 0x37); + rt2800_bbp_write(rt2x00dev, 159, g_imb & 0x3f); + rt2800_bbp_write(rt2x00dev, 158, 0x35); + rt2800_bbp_write(rt2x00dev, 159, ph_rx & 0x3f); + } else { ++ //serge: just to see values ++ pr_info("RXIQ RX1 g_imb (0x55, %2x) ph_rx (0x53, %2x)\n", ++ g_imb & 0x3f, ++ ph_rx & 0x3f ++ ); + rt2800_bbp_write(rt2x00dev, 158, 0x55); + rt2800_bbp_write(rt2x00dev, 159, g_imb & 0x3f); + rt2800_bbp_write(rt2x00dev, 158, 0x53); +@@ -9745,6 +9852,15 @@ void rt2800_loft_iq_calibration(struct r + } + + for (rf_alc_idx = 0; rf_alc_idx < 3; rf_alc_idx++) { ++ //serge: just to see values ++ pr_info("LOFT ALC (0xb0, %2x) I0 (0xb1, %2x) Q0 (0xb2, %2x) I1 (0xb8, %2x) Q1 (0xb9, %2x)\n", ++ rf_alc_idx, ++ loft_dc_search_result[CHAIN_0][rf_alc_idx][0x00] & 0x3F, ++ loft_dc_search_result[CHAIN_0][rf_alc_idx][0x01] & 0x3F, ++ loft_dc_search_result[CHAIN_1][rf_alc_idx][0x00] & 0x3F, ++ loft_dc_search_result[CHAIN_1][rf_alc_idx][0x01] & 0x3F ++ ); ++ + for (idx = 0; idx < 4; idx++) { + rt2800_bbp_write(rt2x00dev, 158, 0xB0); + bbp = (idx<<2) + rf_alc_idx; +@@ -10669,6 +10785,7 @@ static void rt2800_init_rfcsr_6352(struc + rt2800_rfcsr_write_dccal(rt2x00dev, 17, 0x7C); + } + ++ rt6352_enable_pa_pin(rt2x00dev, 0);//serge: vendor driver do it before calibration (7b) + rt2800_r_calibration(rt2x00dev); + rt2800_rf_self_txdc_cal(rt2x00dev); + rt2800_rxdcoc_calibration(rt2x00dev); +@@ -10676,6 +10793,29 @@ static void rt2800_init_rfcsr_6352(struc + rt2800_bw_filter_calibration(rt2x00dev, false); + rt2800_loft_iq_calibration(rt2x00dev); + rt2800_rxiq_calibration(rt2x00dev); ++ rt6352_enable_pa_pin(rt2x00dev, 1);//serge: vendor driver do it after calibration (7b) ++ /* Vendor driver restore iLNA/iPA before ++ recalibration and set correct values after. ++ Openwrt driver init iLNA and iPA but restore only ++ ePA values after recalibration. ++ So set eLNA values only ++ */ ++ if (rt2x00_has_cap_external_lna_bg(rt2x00dev)) {//serge: rf regs never corrected for eLNA (7a) ++ rt2x00_info(rt2x00dev, "Correct RF/BBP for eLNA!\n"); ++ rt2800_rfcsr_write_chanreg(rt2x00dev, 14, 0x66); ++ rt2800_rfcsr_write_chanreg(rt2x00dev, 17, 0x20); ++ rt2800_rfcsr_write_chanreg(rt2x00dev, 18, 0x42); ++ rt2800_bbp_write(rt2x00dev, 75, 0x68);//serge: move bbp eLNA init here? ++ rt2800_bbp_write(rt2x00dev, 76, 0x4C); ++ rt2800_bbp_write(rt2x00dev, 79, 0x1C); ++ rt2800_bbp_write(rt2x00dev, 80, 0x0C); ++ rt2800_bbp_write(rt2x00dev, 82, 0xB6); ++ /* bank 0 RF reg 42 and glrt BBP reg 141 ++ will be set in config channel function ++ in dependence of channel and HT20/HT40 ++ so don't touch it ++ */ ++ } + } + + static void rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev) +--- a/drivers/net/wireless/ralink/rt2x00/rt2x00.h ++++ b/drivers/net/wireless/ralink/rt2x00/rt2x00.h +@@ -28,6 +28,7 @@ + #include + #include + #include ++#include + #include + + #include +@@ -1029,6 +1030,11 @@ struct rt2x00_dev { + + /* Clock for System On Chip devices. */ + struct clk *clk; ++ ++ /* pinctrl and states for System On Chip devices with PA/LNA. */ ++ struct pinctrl *pinctrl; ++ struct pinctrl_state *pins_default; ++ struct pinctrl_state *pins_pa_gpio; + }; + + struct rt2x00_bar_list_entry { +--- a/drivers/net/wireless/ralink/rt2x00/rt2x00soc.c ++++ b/drivers/net/wireless/ralink/rt2x00/rt2x00soc.c +@@ -97,6 +97,21 @@ int rt2x00soc_probe(struct platform_devi + if (retval) + goto exit_free_reg; + ++ rt2x00dev->pinctrl = devm_pinctrl_get(&pdev->dev); ++ if (IS_ERR(rt2x00dev->pinctrl)) { ++ rt2x00dev->pinctrl = NULL; ++ rt2x00dev->pins_default = NULL; ++ rt2x00dev->pins_pa_gpio = NULL; ++ } else { ++ rt2x00dev->pins_default = pinctrl_lookup_state(rt2x00dev->pinctrl, "default"); ++ if (IS_ERR(rt2x00dev->pins_default)) ++ rt2x00dev->pins_default = NULL; ++ ++ rt2x00dev->pins_pa_gpio = pinctrl_lookup_state(rt2x00dev->pinctrl, "pa_gpio"); ++ if (IS_ERR(rt2x00dev->pins_pa_gpio)) ++ rt2x00dev->pins_pa_gpio = NULL; ++ } ++ + return 0; + + exit_free_reg: diff --git a/target/linux/ramips/dts/mt7620a.dtsi b/target/linux/ramips/dts/mt7620a.dtsi index c33dd135fe..4b6fa60dc8 100644 --- a/target/linux/ramips/dts/mt7620a.dtsi +++ b/target/linux/ramips/dts/mt7620a.dtsi @@ -420,6 +420,13 @@ }; }; + pa_gpio_pins: pa_gpio { + pa { + groups = "pa"; + function = "gpio"; + }; + }; + sdhci_pins: sdhci { sdhci { groups = "nd_sd"; diff --git a/target/linux/ramips/dts/mt7620a_buffalo_whr-300hp2.dts b/target/linux/ramips/dts/mt7620a_buffalo_whr-300hp2.dts index 7c8caa5066..4b960da312 100644 --- a/target/linux/ramips/dts/mt7620a_buffalo_whr-300hp2.dts +++ b/target/linux/ramips/dts/mt7620a_buffalo_whr-300hp2.dts @@ -147,8 +147,9 @@ &wmac { ralink,mtd-eeprom = <&factory 0x0>; - pinctrl-names = "default"; + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; }; &factory { diff --git a/target/linux/ramips/dts/mt7620a_cameo_810.dtsi b/target/linux/ramips/dts/mt7620a_cameo_810.dtsi index 3174b98bbf..d0113f5560 100644 --- a/target/linux/ramips/dts/mt7620a_cameo_810.dtsi +++ b/target/linux/ramips/dts/mt7620a_cameo_810.dtsi @@ -138,8 +138,9 @@ }; &wmac { - pinctrl-names = "default"; + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; ralink,mtd-eeprom = <&factory 0x0>; nvmem-cells = <&macaddr_factory_28>; diff --git a/target/linux/ramips/dts/mt7620a_dlink_dch-m225.dts b/target/linux/ramips/dts/mt7620a_dlink_dch-m225.dts index 68b733cade..2884bfdb04 100644 --- a/target/linux/ramips/dts/mt7620a_dlink_dch-m225.dts +++ b/target/linux/ramips/dts/mt7620a_dlink_dch-m225.dts @@ -174,8 +174,9 @@ &wmac { ralink,mtd-eeprom = <&factory 0x0>; - pinctrl-names = "default"; + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; }; &factory { diff --git a/target/linux/ramips/dts/mt7620a_fon_fon2601.dts b/target/linux/ramips/dts/mt7620a_fon_fon2601.dts index 69ddea589b..8f95204ad1 100644 --- a/target/linux/ramips/dts/mt7620a_fon_fon2601.dts +++ b/target/linux/ramips/dts/mt7620a_fon_fon2601.dts @@ -143,8 +143,10 @@ &wmac { ralink,mtd-eeprom = <&factory 0x0>; - pinctrl-names = "default"; + + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>, <&wled_pins>; + pinctrl-1 = <&pa_gpio_pins>, <&wled_pins>; }; &pcie { diff --git a/target/linux/ramips/dts/mt7620a_hiwifi_hc5861.dts b/target/linux/ramips/dts/mt7620a_hiwifi_hc5861.dts index 10aa0ddf6f..87eacb13d7 100644 --- a/target/linux/ramips/dts/mt7620a_hiwifi_hc5861.dts +++ b/target/linux/ramips/dts/mt7620a_hiwifi_hc5861.dts @@ -107,6 +107,7 @@ }; &wmac { - pinctrl-names = "default"; + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; }; diff --git a/target/linux/ramips/dts/mt7620a_lenovo_newifi-y1.dtsi b/target/linux/ramips/dts/mt7620a_lenovo_newifi-y1.dtsi index c7b7ea7b90..5e834d291d 100644 --- a/target/linux/ramips/dts/mt7620a_lenovo_newifi-y1.dtsi +++ b/target/linux/ramips/dts/mt7620a_lenovo_newifi-y1.dtsi @@ -90,9 +90,11 @@ }; &wmac { - ralink,mtd-eeprom = <&factory 0x0>; - pinctrl-names = "default"; + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; + + ralink,mtd-eeprom = <&factory 0x0>; }; &state_default { diff --git a/target/linux/ramips/dts/mt7620a_phicomm_k2-v22.4.dts b/target/linux/ramips/dts/mt7620a_phicomm_k2-v22.4.dts index 4e9fc1307b..52d131556d 100644 --- a/target/linux/ramips/dts/mt7620a_phicomm_k2-v22.4.dts +++ b/target/linux/ramips/dts/mt7620a_phicomm_k2-v22.4.dts @@ -18,6 +18,7 @@ }; &wmac { - pinctrl-names = "default"; + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; }; diff --git a/target/linux/ramips/dts/mt7620a_phicomm_k2-v22.5.dts b/target/linux/ramips/dts/mt7620a_phicomm_k2-v22.5.dts index 2a682872c6..cf9d0b290c 100644 --- a/target/linux/ramips/dts/mt7620a_phicomm_k2-v22.5.dts +++ b/target/linux/ramips/dts/mt7620a_phicomm_k2-v22.5.dts @@ -24,6 +24,7 @@ }; &wmac { - pinctrl-names = "default"; + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; }; diff --git a/target/linux/ramips/dts/mt7620a_phicomm_k2g.dts b/target/linux/ramips/dts/mt7620a_phicomm_k2g.dts index d113edc19f..bc934d7058 100644 --- a/target/linux/ramips/dts/mt7620a_phicomm_k2g.dts +++ b/target/linux/ramips/dts/mt7620a_phicomm_k2g.dts @@ -42,6 +42,7 @@ }; &wmac { - pinctrl-names = "default"; + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; }; diff --git a/target/linux/ramips/dts/mt7620a_tplink_archer-c20-v1.dts b/target/linux/ramips/dts/mt7620a_tplink_archer-c20-v1.dts index e3c077cb0d..8fe5b9c3a2 100644 --- a/target/linux/ramips/dts/mt7620a_tplink_archer-c20-v1.dts +++ b/target/linux/ramips/dts/mt7620a_tplink_archer-c20-v1.dts @@ -69,8 +69,9 @@ }; &wmac { - pinctrl-names = "default"; + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; nvmem-cells = <&macaddr_rom_f100>; nvmem-cell-names = "mac-address"; diff --git a/target/linux/ramips/dts/mt7620a_tplink_archer-c50-v1.dts b/target/linux/ramips/dts/mt7620a_tplink_archer-c50-v1.dts index aefd951f43..4dbd1b2a98 100644 --- a/target/linux/ramips/dts/mt7620a_tplink_archer-c50-v1.dts +++ b/target/linux/ramips/dts/mt7620a_tplink_archer-c50-v1.dts @@ -69,8 +69,9 @@ }; &wmac { - pinctrl-names = "default"; + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; nvmem-cells = <&macaddr_rom_f100>; nvmem-cell-names = "mac-address"; diff --git a/target/linux/ramips/dts/mt7620a_wavlink_wl-wn530hg4.dts b/target/linux/ramips/dts/mt7620a_wavlink_wl-wn530hg4.dts index b0522de7d0..9f58fb86ee 100644 --- a/target/linux/ramips/dts/mt7620a_wavlink_wl-wn530hg4.dts +++ b/target/linux/ramips/dts/mt7620a_wavlink_wl-wn530hg4.dts @@ -131,8 +131,9 @@ }; &wmac { - pinctrl-names = "default"; + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; ralink,mtd-eeprom = <&factory 0x0>; }; diff --git a/target/linux/ramips/dts/mt7620a_xiaomi_miwifi-mini.dts b/target/linux/ramips/dts/mt7620a_xiaomi_miwifi-mini.dts index 9f5df5dd79..1dd3f2eb47 100644 --- a/target/linux/ramips/dts/mt7620a_xiaomi_miwifi-mini.dts +++ b/target/linux/ramips/dts/mt7620a_xiaomi_miwifi-mini.dts @@ -146,8 +146,10 @@ &wmac { ralink,mtd-eeprom = <&factory 0x0>; - pinctrl-names = "default"; + + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; }; &pcie { diff --git a/target/linux/ramips/dts/mt7620a_youku_yk-l1.dtsi b/target/linux/ramips/dts/mt7620a_youku_yk-l1.dtsi index ac874cef3d..d15d2c0f4b 100644 --- a/target/linux/ramips/dts/mt7620a_youku_yk-l1.dtsi +++ b/target/linux/ramips/dts/mt7620a_youku_yk-l1.dtsi @@ -113,6 +113,10 @@ &wmac { ralink,mtd-eeprom = <&factory 0x0>; + + pinctrl-names = "default", "pa_gpio"; + pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; }; &sdhci { diff --git a/target/linux/ramips/dts/mt7620a_zbtlink_zbt-ape522ii.dts b/target/linux/ramips/dts/mt7620a_zbtlink_zbt-ape522ii.dts index 6fcda971a6..ceb348e1d2 100644 --- a/target/linux/ramips/dts/mt7620a_zbtlink_zbt-ape522ii.dts +++ b/target/linux/ramips/dts/mt7620a_zbtlink_zbt-ape522ii.dts @@ -106,8 +106,10 @@ &wmac { ralink,mtd-eeprom = <&factory 0x0>; - pinctrl-names = "default"; + + pinctrl-names = "default", "pa_gpio"; pinctrl-0 = <&pa_pins>; + pinctrl-1 = <&pa_gpio_pins>; }; &pcie {