From: Jyri Sarha Date: Mon, 27 May 2019 13:47:56 +0000 (+0300) Subject: dt-bindings: display: sii902x: Add HDMI audio bindings X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=3f18021f43a3503e43759fc158e938045cdd7219;p=openwrt%2Fstaging%2Fblogic.git dt-bindings: display: sii902x: Add HDMI audio bindings The sii902x chip family supports also HDMI audio. Add binding for describing the necessary i2s and mclk wiring for it. Signed-off-by: Jyri Sarha Reviewed-by: Rob Herring Signed-off-by: Andrzej Hajda Link: https://patchwork.freedesktop.org/patch/msgid/f790277fabc45f987f90075dd842368705226a84.1558964241.git.jsarha@ti.com --- diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt index c4c1855ca654..2df44b7d3821 100644 --- a/Documentation/devicetree/bindings/display/bridge/sii902x.txt +++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt @@ -9,6 +9,40 @@ Optional properties: about hotplug events. - reset-gpios: OF device-tree gpio specification for RST_N pin. + HDMI audio properties: + - #sound-dai-cells: <0> or <1>. <0> if only i2s or spdif pin + is wired, <1> if the both are wired. HDMI audio is + configured only if this property is found. + - sil,i2s-data-lanes: Array of up to 4 integers with values of 0-3 + Each integer indicates which i2s pin is connected to which + audio fifo. The first integer selects i2s audio pin for the + first audio fifo#0 (HDMI channels 1&2), second for fifo#1 + (HDMI channels 3&4), and so on. There is 4 fifos and 4 i2s + pins (SD0 - SD3). Any i2s pin can be connected to any fifo, + but there can be no gaps. E.g. an i2s pin must be mapped to + fifo#0 and fifo#1 before mapping a channel to fifo#2. Default + value is <0>, describing SD0 pin beiging routed to hdmi audio + fifo #0. + - clocks: phandle and clock specifier for each clock listed in + the clock-names property + - clock-names: "mclk" + Describes SII902x MCLK input. MCLK is used to produce + HDMI audio CTS values. This property is required if + "#sound-dai-cells"-property is present. This property follows + Documentation/devicetree/bindings/clock/clock-bindings.txt + consumer binding. + + If HDMI audio is configured the sii902x device becomes an I2S + and/or spdif audio codec component (e.g a digital audio sink), + that can be used in configuring a full audio devices with + simple-card or audio-graph-card binding. See their binding + documents on how to describe the way the sii902x device is + connected to the rest of the audio system: + Documentation/devicetree/bindings/sound/simple-card.txt + Documentation/devicetree/bindings/sound/audio-graph-card.txt + Note: In case of the audio-graph-card binding the used port + index should be 3. + Optional subnodes: - video input: this subnode can contain a video input port node to connect the bridge to a display controller output (See this @@ -21,6 +55,12 @@ Example: compatible = "sil,sii9022"; reg = <0x39>; reset-gpios = <&pioA 1 0>; + + #sound-dai-cells = <0>; + sil,i2s-data-lanes = < 0 1 2 >; + clocks = <&mclk>; + clock-names = "mclk"; + ports { #address-cells = <1>; #size-cells = <0>;