From: John Crispin <john@openwrt.org>
Date: Sun, 30 Mar 2014 09:16:52 +0000 (+0000)
Subject: lantiq: do an endianness swap to the RT2860 eeprom for ARV752DPW(22)
X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=42e8cb6388a7f9bfd8ff820a5af9193e8fb67fa8;p=openwrt%2Fstaging%2Fadrian.git

lantiq: do an endianness swap to the RT2860 eeprom for ARV752DPW(22)

ARV7510PW22, ARV752DPW and ARV752DPW22 have the RT2860 eeprom stored in
flash as big-endian, but the driver needs it in little-endian format. We
have to swab it before handing it over. This requires my earlier patch
for busybox.

Funnily enough, ARV752DPW works also with the incorrect eeprom, but
undoubtedly unoptimally. I have a hunch that also the final remaining
Lantiq board would require this swabbing, but I'm not sure, so I just
swab it in the three boards that I know about.

v2:
* Swab also on ARV7510PW22 based on feedback from Alvaro Rojas
* Fix the offset with bs=2

Signed-off-by: Matti Laakso <malaakso at elisanet.fi>

SVN-Revision: 40328
---

diff --git a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
index a849584fcf..427c5fc7a2 100644
--- a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
+++ b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
@@ -10,6 +10,7 @@ rt2x00_eeprom_extract() {
 	local part=$1
 	local offset=$2
 	local count=$3
+	local swab=$4
 	local mtd
 
 	. /lib/functions.sh
@@ -18,8 +19,13 @@ rt2x00_eeprom_extract() {
 	[ -n "$mtd" ] || \
 		rt2x00_eeprom_die "no mtd device found for partition $part"
 
-	dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count || \
-		rt2x00_eeprom_die "failed to extract from $mtd"
+	if [ $swab -gt 0 ]; then
+		dd if=$mtd of=/lib/firmware/$FIRMWARE bs=2 skip=$offset count=$count conv=swab || \
+			rt2x00_eeprom_die "failed to extract from $mtd"
+	else
+		dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count || \
+			rt2x00_eeprom_die "failed to extract from $mtd"
+	fi
 }
 
 [ -e /lib/firmware/$FIRMWARE ] && exit 0
@@ -29,8 +35,11 @@ case "$FIRMWARE" in
 "RT2860.eeprom" )
 	local board=$(lantiq_board_id)
 	case $board in
-	ARV7510PW22|ARV7519PW|ARV7525PW|ARV752DPW|ARV752DPW22)
-		rt2x00_eeprom_extract "board_config" 1040 512
+	ARV7510PW22|ARV7519PW|ARV752DPW|ARV752DPW22)
+		rt2x00_eeprom_extract "board_config" 520 256 1
+		;;
+	ARV7525PW)
+		rt2x00_eeprom_extract "board_config" 1040 512 0
 		;;
 	*)
 		rt2x00_eeprom_die "board $board is not supported yet"