From: Ian Oderon Date: Sat, 9 Dec 2023 04:48:35 +0000 (+0800) Subject: mediatek: add support for Zbtlink ZBT-Z8103AX X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=4300bc668819a77226b6e8ea079d3067f216e7bb;p=openwrt%2Fstaging%2Flinusw.git mediatek: add support for Zbtlink ZBT-Z8103AX Specifications: SoC: MediaTek MT7981B RAM: 256MiB Flash: SPI-NAND 128 MiB Switch: 1 WAN, 3 LAN (Gigabit) Buttons: Reset, Mesh Power: DC 12V 1A WiFi: MT7976CN UART: 115200n8 UART Layout: VCC-RX-TX-GND No. of Antennas: 6 Note: Upon opening the router, only 5 antennas were connected to the mainboard. Led Layout: Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi Buttons: Reset-Mesh Installation: A. Through OpenWrt Dashboard: If your router comes with OpenWrt preinstalled (modified by the seller), you can easily upgrade by going to the dashboard (192.168.1.1) and then navigate to System -> Backup/Flash firmware, then flash the firmware B. Through TFTP Standard installation via UART: 1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin). 2. Power on the router. Make sure that you can access your router via UART. 3. Restart the router then repeatedly press ctrl + c to skip default boot. 4. Type > bootmenu 5. Press '2' to select upgrade firmware 6. Press 'Y' on 'Run image after upgrading?' 7. Press '0' and hit 'enter' to select TFTP client (default) 8. Fill the U-Boot's IP address and TFTP server's IP address. 9. Finally, enter the 'firmware' filename. Signed-off-by: Ian Oderon --- diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic index 050e1173c3..dd6726713b 100644 --- a/package/boot/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-envtools/files/mediatek_filogic @@ -56,7 +56,8 @@ cmcc,rax3000m) ;; cetron,ct3003|\ netgear,wax220|\ -zbtlink,zbt-z8102ax) +zbtlink,zbt-z8102ax|\ +zbtlink,zbt-z8103ax) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" ;; h3c,magic-nx30-pro|\ diff --git a/target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax.dts b/target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax.dts new file mode 100644 index 0000000000..2b079f5bca --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax.dts @@ -0,0 +1,269 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "mt7981.dtsi" + +/ { + model = "Zbtlink ZBT-Z8103AX"; + compatible = "zbtlink,zbt-z8103ax", "mediatek,mt7981"; + + aliases { + serial0 = &uart0; + led-boot = &led_status_green; + led-failsafe = &led_status_red; + led-running = &led_status_green; + led-upgrade = &led_status_green; + label-mac-device = &gmac0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 loglevel=8"; + }; + + memory { + reg = <0 0x40000000 0 0x10000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + button-mesh { + label = "mesh"; + linux,code = ; + linux,input-type = ; + gpios = <&pio 0 GPIO_ACTIVE_HIGH>; + }; + + button-reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-wan { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&pio 8 GPIO_ACTIVE_LOW>; + }; + + led-status-blue { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&pio 23 GPIO_ACTIVE_HIGH>; + }; + + led_status_green: led-status-green { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&pio 24 GPIO_ACTIVE_LOW>; + }; + + led_status_red: led-status-red { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&pio 25 GPIO_ACTIVE_LOW>; + }; + + led-wlan2g { + color = ; + function = LED_FUNCTION_WLAN; + gpios = <&pio 34 GPIO_ACTIVE_LOW>; + function-enumerator = <0>; + linux,default-trigger = "phy0tpt"; + }; + + led-wlan5g { + color = ; + function = LED_FUNCTION_WLAN; + gpios = <&pio 35 GPIO_ACTIVE_LOW>; + function-enumerator = <1>; + linux,default-trigger = "phy1tpt"; + }; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + /* LAN */ + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_factory_4 2>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + /* WAN */ + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "gmii"; + phy-handle = <&int_gbe_phy>; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_factory_4 3>; + }; +}; + +&mdio_bus { + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand@0 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bl2"; + reg = <0x0000000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x100000 0x80000>; + }; + + partition@180000 { + label = "Factory"; + reg = <0x180000 0x200000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory: eeprom@0 { + reg = <0x0 0x1000>; + }; + + macaddr_factory_4: macaddr@4 { + compatible = "mac-base"; + reg = <0x4 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x580000 0x4000000>; + }; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = ; + bias-pull-up = ; + }; + + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = ; + bias-pull-down = ; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + nvmem-cells = <&eeprom_factory>; + nvmem-cell-names = "eeprom"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index b1411d56d3..f1fd58f1d0 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -35,6 +35,9 @@ xiaomi,redmi-router-ax6000-stock|\ xiaomi,redmi-router-ax6000-ubootmod) ucidef_set_led_netdev "wan" "wan" "rgb:network" "wan" ;; +zbtlink,zbt-z8103ax) + ucidef_set_led_netdev "wan" "wan" "green:wan" "eth1" "link tx rx" + ;; zyxel_ex5601-t0-stock|\ zyxel,ex5601-t0-ubootmod) ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0" "link tx rx" diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 1c41a9f8ed..4ffb7e53bf 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -33,7 +33,8 @@ mediatek_setup_interfaces() ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan ;; cmcc,rax3000m|\ - h3c,magic-nx30-pro) + h3c,magic-nx30-pro|\ + zbtlink,zbt-z8103ax) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" eth1 ;; glinet,gl-mt2500|\ diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 7f1d0c5364..bf7426fbee 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -105,6 +105,7 @@ case "$board" in [ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress ;; zbtlink,zbt-z8102ax|\ + zbtlink,zbt-z8103ax|\ zyxel,ex5601-t0|\ zyxel,ex5601-t0-ubootmod) addr=$(mtd_get_mac_binary "Factory" 0x4) diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index ab242e2635..afbdfefd6f 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -831,6 +831,23 @@ define Device/zbtlink_zbt-z8102ax endef TARGET_DEVICES += zbtlink_zbt-z8102ax +define Device/zbtlink_zbt-z8103ax + DEVICE_VENDOR := Zbtlink + DEVICE_MODEL := ZBT-Z8103AX + DEVICE_DTS := mt7981b-zbtlink-zbt-z8103ax + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware + KERNEL_IN_UBI := 1 + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 65536k + IMAGES += factory.bin + IMAGE/factory.bin := append-ubi | check-size $$(IMAGE_SIZE) + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += zbtlink_zbt-z8103ax + define Device/zyxel_ex5601-t0-stock DEVICE_VENDOR := Zyxel DEVICE_MODEL := EX5601-T0