From: Stefan Wahren <stefan.wahren@i2se.com>
Date: Mon, 29 May 2017 11:57:22 +0000 (+0200)
Subject: dt-bindings: qca7000: rename binding
X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=4aab28ca446f39ded6fb60c2344d349fd1771d5e;p=openwrt%2Fstaging%2Fblogic.git

dt-bindings: qca7000: rename binding

Before we can merge the QCA7000 UART binding the document needs to be
renamed.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---

diff --git a/Documentation/devicetree/bindings/net/qca,qca7000.txt b/Documentation/devicetree/bindings/net/qca,qca7000.txt
new file mode 100644
index 000000000000..a37f65678399
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qca,qca7000.txt
@@ -0,0 +1,56 @@
+* Qualcomm QCA7000
+
+The QCA7000 is a serial-to-powerline bridge with a host interface which could
+be configured either as SPI or UART slave. This configuration is done by
+the QCA7000 firmware.
+
+(a) Ethernet over SPI
+
+In order to use the QCA7000 as SPI device it must be defined as a child of a
+SPI master in the device tree.
+
+Required properties:
+- compatible	    : Should be "qca,qca7000"
+- reg		    : Should specify the SPI chip select
+- interrupts	    : The first cell should specify the index of the source
+		      interrupt and the second cell should specify the trigger
+		      type as rising edge
+- spi-cpha	    : Must be set
+- spi-cpol	    : Must be set
+
+Optional properties:
+- interrupt-parent  : Specify the pHandle of the source interrupt
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at.
+		      Numbers smaller than 1000000 or greater than 16000000
+		      are invalid. Missing the property will set the SPI
+		      frequency to 8000000 Hertz.
+- local-mac-address : see ./ethernet.txt
+- qca,legacy-mode   : Set the SPI data transfer of the QCA7000 to legacy mode.
+		      In this mode the SPI master must toggle the chip select
+		      between each data word. In burst mode these gaps aren't
+		      necessary, which is faster. This setting depends on how
+		      the QCA7000 is setup via GPIO pin strapping. If the
+		      property is missing the driver defaults to burst mode.
+
+SPI Example:
+
+/* Freescale i.MX28 SPI master*/
+ssp2: spi@80014000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	qca7000: ethernet@0 {
+		compatible = "qca,qca7000";
+		reg = <0x0>;
+		interrupt-parent = <&gpio3>;      /* GPIO Bank 3 */
+		interrupts = <25 0x1>;            /* Index: 25, rising edge */
+		spi-cpha;                         /* SPI mode: CPHA=1 */
+		spi-cpol;                         /* SPI mode: CPOL=1 */
+		spi-max-frequency = <8000000>;    /* freq: 8 MHz */
+		local-mac-address = [ A0 B0 C0 D0 E0 F0 ];
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt
deleted file mode 100644
index a37f65678399..000000000000
--- a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt
+++ /dev/null
@@ -1,56 +0,0 @@
-* Qualcomm QCA7000
-
-The QCA7000 is a serial-to-powerline bridge with a host interface which could
-be configured either as SPI or UART slave. This configuration is done by
-the QCA7000 firmware.
-
-(a) Ethernet over SPI
-
-In order to use the QCA7000 as SPI device it must be defined as a child of a
-SPI master in the device tree.
-
-Required properties:
-- compatible	    : Should be "qca,qca7000"
-- reg		    : Should specify the SPI chip select
-- interrupts	    : The first cell should specify the index of the source
-		      interrupt and the second cell should specify the trigger
-		      type as rising edge
-- spi-cpha	    : Must be set
-- spi-cpol	    : Must be set
-
-Optional properties:
-- interrupt-parent  : Specify the pHandle of the source interrupt
-- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at.
-		      Numbers smaller than 1000000 or greater than 16000000
-		      are invalid. Missing the property will set the SPI
-		      frequency to 8000000 Hertz.
-- local-mac-address : see ./ethernet.txt
-- qca,legacy-mode   : Set the SPI data transfer of the QCA7000 to legacy mode.
-		      In this mode the SPI master must toggle the chip select
-		      between each data word. In burst mode these gaps aren't
-		      necessary, which is faster. This setting depends on how
-		      the QCA7000 is setup via GPIO pin strapping. If the
-		      property is missing the driver defaults to burst mode.
-
-SPI Example:
-
-/* Freescale i.MX28 SPI master*/
-ssp2: spi@80014000 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	compatible = "fsl,imx28-spi";
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi2_pins_a>;
-	status = "okay";
-
-	qca7000: ethernet@0 {
-		compatible = "qca,qca7000";
-		reg = <0x0>;
-		interrupt-parent = <&gpio3>;      /* GPIO Bank 3 */
-		interrupts = <25 0x1>;            /* Index: 25, rising edge */
-		spi-cpha;                         /* SPI mode: CPHA=1 */
-		spi-cpol;                         /* SPI mode: CPOL=1 */
-		spi-max-frequency = <8000000>;    /* freq: 8 MHz */
-		local-mac-address = [ A0 B0 C0 D0 E0 F0 ];
-	};
-};