From: Jonas Gorski Date: Thu, 21 May 2015 19:31:54 +0000 (+0000) Subject: brcm63xx: Add Huawei HG655b support X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=509c3211d66ec5d3bc741361c06eff993bf39b85;p=openwrt%2Fstaging%2Flinusw.git brcm63xx: Add Huawei HG655b support This patch adds support for the Huawei HG655b. Nothing much special in this router, it's just another BCM6368 with a Ralink RT3062 wifi chip and the calibration data embedded in the main flash chip at offset 0x7c0000. There is also configuration data used by the OEM firmware before the cal_data partition, this area is protected by the board_data partition in this patch. Signed-off-by: Daniel Gonzalez Signed-off-by: Jonas Gorski SVN-Revision: 45708 --- diff --git a/target/linux/brcm63xx/base-files/etc/diag.sh b/target/linux/brcm63xx/base-files/etc/diag.sh index 03d98b9146..c330674fe3 100644 --- a/target/linux/brcm63xx/base-files/etc/diag.sh +++ b/target/linux/brcm63xx/base-files/etc/diag.sh @@ -89,6 +89,9 @@ set_state() { hg520) status_led="HW520:green:net" ;; + hg655b) + status_led="HW65x:green:power" + ;; p870hw-51a_v2) status_led="P870HW-51a:green:power" ;; diff --git a/target/linux/brcm63xx/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/brcm63xx/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom index 9a324eacbd..434748537e 100644 --- a/target/linux/brcm63xx/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom +++ b/target/linux/brcm63xx/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom @@ -34,6 +34,9 @@ case "$FIRMWARE" in hg556a_c) rt2x00_eeprom_extract "cal_data" 130560 512 ;; + hg655b) + rt2x00_eeprom_extract "cal_data" 0 512 + ;; *) rt2x00_eeprom_die "board $board is not supported yet" ;; diff --git a/target/linux/brcm63xx/base-files/etc/uci-defaults/01_leds b/target/linux/brcm63xx/base-files/etc/uci-defaults/01_leds index 58404a165f..b964bdb229 100644 --- a/target/linux/brcm63xx/base-files/etc/uci-defaults/01_leds +++ b/target/linux/brcm63xx/base-files/etc/uci-defaults/01_leds @@ -34,6 +34,9 @@ hg556a_*) ucidef_set_led_netdev "lan" "LAN" "HW556:red:dsl" "eth0" ucidef_set_led_usbdev "usb" "USB" "HW556:red:hspa" "1-2" ;; +hg655b) + ucidef_set_led_usbdev "usb" "USB" "HW65x:green:usb" "1-2" + ;; homehub2a) ucidef_set_led_netdev "lan" "LAN" "HOMEHUB2A:blue:broadband" "eth0.1" ucidef_set_led_netdev "wlan0" "WIFI" "HOMEHUB2A:green:wireless" "wlan0" diff --git a/target/linux/brcm63xx/base-files/etc/uci-defaults/02_network b/target/linux/brcm63xx/base-files/etc/uci-defaults/02_network index 814e1003cd..e5880eb414 100644 --- a/target/linux/brcm63xx/base-files/etc/uci-defaults/02_network +++ b/target/linux/brcm63xx/base-files/etc/uci-defaults/02_network @@ -92,6 +92,7 @@ dsl-274xb-f |\ dsl-275xb-d |\ fast2504n |\ fast2704v2 |\ +hg655b |\ p870hw-51a_v2 |\ vr-3025un |\ vr-3025u) diff --git a/target/linux/brcm63xx/base-files/lib/brcm63xx.sh b/target/linux/brcm63xx/base-files/lib/brcm63xx.sh index 5cb390f061..0eb9a750ca 100755 --- a/target/linux/brcm63xx/base-files/lib/brcm63xx.sh +++ b/target/linux/brcm63xx/base-files/lib/brcm63xx.sh @@ -156,6 +156,9 @@ brcm63xx_dt_detect() { "Huawei EchoLife HG556a (version C)") board_name="hg556a_c" ;; + "Huawei HG655b") + board_name="hg655b" + ;; "Inteno VG50") board_name="vg50" ;; diff --git a/target/linux/brcm63xx/dts/hg655b.dts b/target/linux/brcm63xx/dts/hg655b.dts new file mode 100644 index 0000000000..256233d7cf --- /dev/null +++ b/target/linux/brcm63xx/dts/hg655b.dts @@ -0,0 +1,110 @@ +/dts-v1/; + +/include/ "bcm6368.dtsi" + +/ { + model = "Huawei HG655b"; + compatible = "huawei,hg655b", "brcm,bcm6368"; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + debounce-interval = <60>; + + wps { + label = "wps"; + gpios = <&gpio0 12 1>; + linux,code = <0x211>; + }; + wlan { + label = "wlan"; + gpios = <&gpio0 23 1>; + linux,code = <0xee>; + }; + reset { + label = "reset"; + gpios = <&gpio1 2 1>; + linux,code = <0x198>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + dsl_green { + label = "HW65x:green:dsl"; + gpios = <&gpio0 2 1>; + }; + internet_green { + label = "HW65x:green:internet"; + gpios = <&gpio0 5 1>; + }; + lan1_green { + label = "HW65x:green:lan1"; + gpios = <&gpio0 6 1>; + }; + lan2_green { + label = "HW65x:green:lan2"; + gpios = <&gpio0 7 1>; + }; + lan3_green { + label = "HW65x:green:lan3"; + gpios = <&gpio0 8 1>; + }; + lan4_green { + label = "HW65x:green:lan4"; + gpios = <&gpio0 9 1>; + }; + usb_green { + label = "HW65x:green:usb"; + gpios = <&gpio0 14 1>; + }; + power_green { + label = "HW65x:green:power"; + gpios = <&gpio0 22 1>; + default-state = "on"; + }; + voip_green { + label = "HW65x:green:voip"; + gpios = <&gpio0 25 1>; + }; + wps_green { + label = "HW65x:green:wps"; + gpios = <&gpio0 27 1>; + }; + }; +}; + +&pflash { + status = "ok"; + + linux,part-probe = "bcm63xxpart"; + + cfe@0 { + label = "CFE"; + reg = <0x000000 0x020000>; + }; + + linux@20000 { + label = "linux"; + reg = <0x020000 0x770000>; + }; + + board_data@790000 { + label = "board_data"; + reg = <0x790000 0x030000>; + }; + + cal_data@7c0000 { + label = "cal_data"; + reg = <0x7c0000 0x020000>; + read-only; + }; + + nvram@7d0000 { + label = "nvram"; + reg = <0x7e0000 0x020000>; + }; +}; diff --git a/target/linux/brcm63xx/image/Makefile b/target/linux/brcm63xx/image/Makefile index e98011d56f..0d8ce5338f 100755 --- a/target/linux/brcm63xx/image/Makefile +++ b/target/linux/brcm63xx/image/Makefile @@ -360,6 +360,8 @@ $(eval $(call ImageDTB,CFEDTB,HG553,HG553,hg553,HW553,6358,--rsa-signature "Echo $(eval $(call ImageDTB,CFEDTB,HG556a_AB,HG556a_A,hg556a-a,HW556,6358,--rsa-signature "EchoLife_HG556a" --image-offset 0x20000 --block-size 0x10000 --tag-version 8)) $(eval $(call ImageDTB,CFEDTB,HG556a_AB,HG556a_B,hg556a-b,HW556,6358,--rsa-signature "EchoLife_HG556a" --image-offset 0x20000 --block-size 0x20000 --tag-version 8)) $(eval $(call ImageDTB,CFEDTB,HG556a_C,HG556a_C,hg556a-c,HW556,6358,--rsa-signature "EchoLife_HG556a" --image-offset 0x20000 --block-size 0x20000 --tag-version 8)) +# Huawei HG655b +$(eval $(call ImageDTB,CFEDTB,HG655b,HG655b,hg655b,HW65x,6368,--image-offset 0x20000 --tag-version 7 --pad 4)) # Inteno VG50 $(eval $(call ImageDTB,Dummy,VG50,vg50,vg50,VW6339GU,63268)) # Inventel Livebox 1 diff --git a/target/linux/brcm63xx/patches-3.18/570-board_HG655b.patch b/target/linux/brcm63xx/patches-3.18/570-board_HG655b.patch new file mode 100644 index 0000000000..903068a842 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/570-board_HG655b.patch @@ -0,0 +1,72 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1928,6 +1928,53 @@ + + .spis = DGND3700v1_3800B_spi_devices, + .num_spis = ARRAY_SIZE(DGND3700v1_3800B_spi_devices), ++}; ++ ++static struct board_info __initdata board_HG655b = { ++ .name = "HW65x", ++ .expected_cpu_id = 0x6368, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 2, ++ ++ .has_caldata = 1, ++ .caldata = { ++ { ++ .vendor = PCI_VENDOR_ID_RALINK, ++ .caldata_offset = 0x7c0000, ++ .slot = 1, ++ .eeprom = "rt2x00.eeprom", ++ }, ++ }, ++ ++ .has_enetsw = 1, ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "port1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "port2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "port3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "port4", ++ }, ++ }, ++ }, + }; + + static struct sprom_fixup __initdata vr3025u_fixups[] = { +@@ -2380,6 +2427,7 @@ + &board_96368mvwg, + &board_96368mvngr, + &board_DGND3700v1_3800B, ++ &board_HG655b, + &board_P870HW51A_V2, + &board_VR3025u, + &board_VR3025un, +@@ -2483,6 +2531,7 @@ + { .compatible = "comtrend,vr-3025u", .data = &board_VR3025u, }, + { .compatible = "comtrend,vr-3025un", .data = &board_VR3025un, }, + { .compatible = "comtrend,wap-5813n", .data = &board_WAP5813n, }, ++ { .compatible = "huawei,hg655b", .data = &board_HG655b, }, + { .compatible = "netgear,dgnd3700v1", .data = &board_DGND3700v1_3800B, }, + { .compatible = "zyxel,p870hw-51a-v2", .data = &board_P870HW51A_V2, }, + #endif diff --git a/target/linux/brcm63xx/profiles/huawei.mk b/target/linux/brcm63xx/profiles/huawei.mk index 594389ec0e..a6764b73e3 100644 --- a/target/linux/brcm63xx/profiles/huawei.mk +++ b/target/linux/brcm63xx/profiles/huawei.mk @@ -43,3 +43,13 @@ define Profile/HG556a_C/Description Package set optimized for Huawei HG556a version C (Ralink). endef $(eval $(call Profile,HG556a_C)) + +define Profile/HG655b + NAME:=Huawei HG655b + PACKAGES:=kmod-rt2800-pci wpad-mini \ + kmod-usb2 kmod-usb-ohci kmod-ledtrig-usbdev +endef +define Profile/HG655b/Description + Package set optimized for Huawei HG655b, HG655d. +endef +$(eval $(call Profile,HG655b))