From: John Crispin Date: Mon, 10 Feb 2020 06:46:56 +0000 (+0100) Subject: bcm53xx: add v5.4 support X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=50c6938b95a0c915c5c8ffe1fe67a94b9402e98e;p=openwrt%2Fstaging%2Fthess.git bcm53xx: add v5.4 support Signed-off-by: John Crispin --- diff --git a/target/linux/bcm53xx/Makefile b/target/linux/bcm53xx/Makefile index 6c19263fdf..b63aeaa0f9 100644 --- a/target/linux/bcm53xx/Makefile +++ b/target/linux/bcm53xx/Makefile @@ -14,8 +14,8 @@ MAINTAINER:=Hauke Mehrtens CPU_TYPE:=cortex-a9 SUBTARGETS:=generic -KERNEL_PATCHVER:=4.14 -KERNEL_TESTING_PATCHVER := 4.19 +KERNEL_PATCHVER:=4.19 +KERNEL_TESTING_PATCHVER:=5.4 define Target/Description Build firmware images for Broadcom based BCM47xx/53xx routers with ARM CPU, *not* MIPS. diff --git a/target/linux/bcm53xx/config-5.4 b/target/linux/bcm53xx/config-5.4 new file mode 100644 index 0000000000..657d49ac01 --- /dev/null +++ b/target/linux/bcm53xx/config-5.4 @@ -0,0 +1,471 @@ +CONFIG_64BIT_TIME=y +# CONFIG_ADIN_PHY is not set +CONFIG_ALIGNMENT_TRAP=y +# CONFIG_AL_FIC is not set +CONFIG_ARCH_32BIT_OFF_T=y +CONFIG_ARCH_BCM=y +CONFIG_ARCH_BCM_5301X=y +CONFIG_ARCH_BCM_53573=y +# CONFIG_ARCH_BCM_HR2 is not set +CONFIG_ARCH_BCM_IPROC=y +CONFIG_ARCH_CLOCKSOURCE_DATA=y +CONFIG_ARCH_HAS_BINFMT_FLAT=y +CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y +CONFIG_ARCH_HAS_ELF_RANDOMIZE=y +CONFIG_ARCH_HAS_FORTIFY_SOURCE=y +CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y +CONFIG_ARCH_HAS_KCOV=y +CONFIG_ARCH_HAS_KEEPINITRD=y +CONFIG_ARCH_HAS_MEMBARRIER_SYNC_CORE=y +CONFIG_ARCH_HAS_PHYS_TO_DMA=y +CONFIG_ARCH_HAS_SETUP_DMA_OPS=y +CONFIG_ARCH_HAS_SET_MEMORY=y +CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y +CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y +CONFIG_ARCH_HAS_TEARDOWN_DMA_OPS=y +CONFIG_ARCH_HAS_TICK_BROADCAST=y +CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_KEEP_MEMBLOCK=y +CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y +# CONFIG_ARCH_MILBEAUT is not set +CONFIG_ARCH_MULTIPLATFORM=y +CONFIG_ARCH_MULTI_V6_V7=y +CONFIG_ARCH_MULTI_V7=y +CONFIG_ARCH_NR_GPIO=0 +CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y +CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y +# CONFIG_ARCH_RDA is not set +CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y +CONFIG_ARCH_SUPPORTS_UPROBES=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARCH_USE_BUILTIN_BSWAP=y +CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y +CONFIG_ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT=y +CONFIG_ARCH_WANT_GENERAL_HUGETLB=y +CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y +CONFIG_ARM=y +CONFIG_ARM_AMBA=y +CONFIG_ARM_APPENDED_DTB=y +CONFIG_ARM_ARCH_TIMER=y +CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y +# CONFIG_ARM_ATAG_DTB_COMPAT is not set +CONFIG_ARM_ERRATA_754322=y +CONFIG_ARM_ERRATA_764369=y +CONFIG_ARM_ERRATA_775420=y +# CONFIG_ARM_ERRATA_814220 is not set +# CONFIG_ARM_ERRATA_857271 is not set +# CONFIG_ARM_ERRATA_857272 is not set +CONFIG_ARM_GIC=y +CONFIG_ARM_GLOBAL_TIMER=y +CONFIG_ARM_HAS_SG_CHAIN=y +CONFIG_ARM_HEAVY_MB=y +CONFIG_ARM_L1_CACHE_SHIFT=6 +CONFIG_ARM_L1_CACHE_SHIFT_6=y +# CONFIG_ARM_LPAE is not set +CONFIG_ARM_PATCH_IDIV=y +CONFIG_ARM_PATCH_PHYS_VIRT=y +# CONFIG_ARM_SP805_WATCHDOG is not set +CONFIG_ARM_THUMB=y +# CONFIG_ARM_THUMBEE is not set +CONFIG_ARM_UNWIND=y +CONFIG_ARM_VIRT_EXT=y +CONFIG_ATAGS=y +CONFIG_AUTO_ZRELADDR=y +# CONFIG_BACKLIGHT_CLASS_DEVICE is not set +CONFIG_BCM47XX_NVRAM=y +CONFIG_BCM47XX_SPROM=y +CONFIG_BCM47XX_WDT=y +CONFIG_BCMA=y +CONFIG_BCMA_BLOCKIO=y +CONFIG_BCMA_DEBUG=y +CONFIG_BCMA_DRIVER_GMAC_CMN=y +CONFIG_BCMA_DRIVER_GPIO=y +CONFIG_BCMA_DRIVER_PCI=y +CONFIG_BCMA_HOST_PCI=y +CONFIG_BCMA_HOST_PCI_POSSIBLE=y +CONFIG_BCMA_HOST_SOC=y +CONFIG_BCMA_SFLASH=y +# CONFIG_BCM_CYGNUS_PHY is not set +CONFIG_BCM_NET_PHYLIB=y +CONFIG_BCM_NS_THERMAL=y +CONFIG_BCM_SR_THERMAL=y +CONFIG_BGMAC=y +CONFIG_BGMAC_BCMA=y +# CONFIG_BGMAC_PLATFORM is not set +CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y +CONFIG_BLK_MQ_PCI=y +CONFIG_BOUNCE=y +CONFIG_BROADCOM_PHY=y +CONFIG_CACHE_L2X0=y +CONFIG_CC_CAN_LINK=y +CONFIG_CC_HAS_ASM_INLINE=y +CONFIG_CC_HAS_KASAN_GENERIC=y +CONFIG_CC_HAS_WARN_MAYBE_UNINITIALIZED=y +CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK=y +CONFIG_CLKSRC_MMIO=y +# CONFIG_CLK_BCM_NS2 is not set +CONFIG_CLK_BCM_NSP=y +# CONFIG_CLK_BCM_SR is not set +CONFIG_CLONE_BACKWARDS=y +CONFIG_COMMON_CLK=y +# CONFIG_COMMON_CLK_FIXED_MMIO is not set +CONFIG_COMMON_CLK_IPROC=y +CONFIG_COMPAT_32BIT_TIME=y +# CONFIG_COUNTER is not set +CONFIG_CPU_32v6K=y +CONFIG_CPU_32v7=y +CONFIG_CPU_ABRT_EV7=y +# CONFIG_CPU_BPREDICT_DISABLE is not set +CONFIG_CPU_CACHE_V7=y +CONFIG_CPU_CACHE_VIPT=y +CONFIG_CPU_COPY_V6=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y +CONFIG_CPU_HAS_ASID=y +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_ICACHE_MISMATCH_WORKAROUND is not set +CONFIG_CPU_PABRT_V7=y +CONFIG_CPU_RMAP=y +CONFIG_CPU_SPECTRE=y +CONFIG_CPU_THUMB_CAPABLE=y +CONFIG_CPU_TLB_V7=y +CONFIG_CPU_V7=y +CONFIG_CRC16=y +CONFIG_CRYPTO_ACOMP2=y +# CONFIG_CRYPTO_ADIANTUM is not set +CONFIG_CRYPTO_AEAD=y +CONFIG_CRYPTO_AEAD2=y +CONFIG_CRYPTO_AKCIPHER2=y +CONFIG_CRYPTO_DEFLATE=y +# CONFIG_CRYPTO_ECRDSA is not set +# CONFIG_CRYPTO_ESSIV is not set +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_HASH_INFO=y +CONFIG_CRYPTO_KPP2=y +CONFIG_CRYPTO_LIB_AES=y +CONFIG_CRYPTO_LZO=y +CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_MANAGER2=y +CONFIG_CRYPTO_NULL2=y +# CONFIG_CRYPTO_OFB is not set +CONFIG_CRYPTO_RNG2=y +# CONFIG_CRYPTO_STREEBOG is not set +# CONFIG_CRYPTO_XXHASH is not set +CONFIG_CRYPTO_ZSTD=y +CONFIG_DCACHE_WORD_ACCESS=y +CONFIG_DEBUG_BCM_5301X=y +CONFIG_DEBUG_INFO=y +CONFIG_DEBUG_LL=y +CONFIG_DEBUG_LL_INCLUDE="debug/8250.S" +CONFIG_DEBUG_MISC=y +# CONFIG_DEBUG_PLIST is not set +CONFIG_DEBUG_UART_8250=y +# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set +CONFIG_DEBUG_UART_8250_SHIFT=0 +CONFIG_DEBUG_UART_PHYS=0x18000300 +CONFIG_DEBUG_UART_VIRT=0xf1000300 +CONFIG_DEBUG_UNCOMPRESS=y +CONFIG_DEBUG_USER=y +CONFIG_DMA_DECLARE_COHERENT=y +CONFIG_DMA_REMAP=y +CONFIG_DTC=y +CONFIG_EARLY_PRINTK=y +CONFIG_EDAC_ATOMIC_SCRUB=y +CONFIG_EDAC_SUPPORT=y +# CONFIG_EXFAT_FS is not set +CONFIG_EXTCON=y +# CONFIG_FIELDBUS_DEV is not set +CONFIG_FIXED_PHY=y +CONFIG_FIX_EARLYCON_MEM=y +# CONFIG_FS_VERITY is not set +# CONFIG_FW_LOADER_COMPRESS is not set +CONFIG_FW_LOADER_PAGED_BUF=y +# CONFIG_FW_LOADER_USER_HELPER_FALLBACK is not set +CONFIG_GENERIC_ALLOCATOR=y +CONFIG_GENERIC_ARCH_TOPOLOGY=y +CONFIG_GENERIC_BUG=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y +CONFIG_GENERIC_CPU_AUTOPROBE=y +CONFIG_GENERIC_EARLY_IOREMAP=y +CONFIG_GENERIC_IDLE_POLL_SETUP=y +CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y +CONFIG_GENERIC_IRQ_MULTI_HANDLER=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_IRQ_SHOW_LEVEL=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_PHY=y +CONFIG_GENERIC_PINCONF=y +CONFIG_GENERIC_PINCTRL_GROUPS=y +CONFIG_GENERIC_PINMUX_FUNCTIONS=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_STRNCPY_FROM_USER=y +CONFIG_GENERIC_STRNLEN_USER=y +CONFIG_GPIOLIB=y +CONFIG_GPIOLIB_IRQCHIP=y +CONFIG_GPIO_74X164=y +# CONFIG_GPIO_AMD_FCH is not set +# CONFIG_GPIO_CADENCE is not set +# CONFIG_GPIO_SAMA5D2_PIOBU is not set +CONFIG_GPIO_SYSFS=y +# CONFIG_HABANA_AI is not set +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDEN_BRANCH_PREDICTOR=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +CONFIG_HAVE_ARCH_AUDITSYSCALL=y +CONFIG_HAVE_ARCH_BITREVERSE=y +CONFIG_HAVE_ARCH_JUMP_LABEL=y +CONFIG_HAVE_ARCH_KGDB=y +CONFIG_HAVE_ARCH_PFN_VALID=y +CONFIG_HAVE_ARCH_SECCOMP_FILTER=y +CONFIG_HAVE_ARCH_THREAD_STRUCT_WHITELIST=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +CONFIG_HAVE_ARM_ARCH_TIMER=y +CONFIG_HAVE_ARM_SCU=y +CONFIG_HAVE_ARM_SMCCC=y +CONFIG_HAVE_ARM_TWD=y +CONFIG_HAVE_CLK=y +CONFIG_HAVE_CLK_PREPARE=y +CONFIG_HAVE_CONTEXT_TRACKING=y +CONFIG_HAVE_C_RECORDMCOUNT=y +CONFIG_HAVE_DEBUG_KMEMLEAK=y +CONFIG_HAVE_DMA_CONTIGUOUS=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y +CONFIG_HAVE_EBPF_JIT=y +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y +CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_HAVE_IDE=y +CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y +CONFIG_HAVE_LD_DEAD_CODE_DATA_ELIMINATION=y +CONFIG_HAVE_MOD_ARCH_SPECIFIC=y +CONFIG_HAVE_NET_DSA=y +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_OPTPROBES=y +CONFIG_HAVE_PCI=y +CONFIG_HAVE_PERF_EVENTS=y +CONFIG_HAVE_PERF_REGS=y +CONFIG_HAVE_PERF_USER_STACK_DUMP=y +CONFIG_HAVE_PROC_CPU=y +CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y +CONFIG_HAVE_RSEQ=y +CONFIG_HAVE_SMP=y +CONFIG_HAVE_SYSCALL_TRACEPOINTS=y +CONFIG_HAVE_UID16=y +CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y +# CONFIG_HEADERS_INSTALL is not set +# CONFIG_HEADER_TEST is not set +CONFIG_HIGHMEM=y +# CONFIG_HIGHPTE is not set +CONFIG_HZ_FIXED=0 +CONFIG_HZ_PERIODIC=y +# CONFIG_I3C is not set +# CONFIG_IGC is not set +# CONFIG_IKHEADERS is not set +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_INIT_ON_ALLOC_DEFAULT_ON is not set +# CONFIG_INIT_ON_FREE_DEFAULT_ON is not set +CONFIG_INIT_STACK_NONE=y +# CONFIG_INTERCONNECT is not set +CONFIG_IO_URING=y +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_DOMAIN_HIERARCHY=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_WORK=y +CONFIG_KASAN_STACK=1 +# CONFIG_LCD_CLASS_DEVICE is not set +# CONFIG_LEDS_TRIGGER_AUDIO is not set +# CONFIG_LEDS_TRIGGER_PATTERN is not set +CONFIG_LIBFDT=y +CONFIG_LOCK_DEBUGGING_SUPPORT=y +# CONFIG_LOCK_EVENT_COUNTS is not set +CONFIG_LOCK_SPIN_ON_OWNER=y +CONFIG_LSM="lockdown,yama,loadpin,safesetid,integrity" +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y +CONFIG_MDIO_BCM_IPROC=y +CONFIG_MDIO_BUS=y +CONFIG_MDIO_BUS_MUX=y +# CONFIG_MDIO_BUS_MUX_BCM_IPROC is not set +CONFIG_MDIO_BUS_MUX_MMIOREG=y +# CONFIG_MDIO_BUS_MUX_MULTIPLEXER is not set +CONFIG_MDIO_DEVICE=y +CONFIG_MEMFD_CREATE=y +CONFIG_MFD_SYSCON=y +# CONFIG_MFD_TQMX86 is not set +CONFIG_MIGHT_HAVE_CACHE_L2X0=y +CONFIG_MIGRATION=y +# CONFIG_MISC_ALCOR_PCI is not set +CONFIG_MODULES_USE_ELF_REL=y +# CONFIG_MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS is not set +CONFIG_MTD_BCM47XXSFLASH=y +CONFIG_MTD_BCM47XX_PARTS=y +# CONFIG_MTD_HYPERBUS is not set +CONFIG_MTD_PARSER_TRX=y +# CONFIG_MTD_RAW_NAND is not set +CONFIG_MTD_SPI_NOR=y +CONFIG_MTD_SPLIT_SEAMA_FW=y +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_BEB_LIMIT=20 +CONFIG_MTD_UBI_BLOCK=y +# CONFIG_MTD_UBI_FASTMAP is not set +# CONFIG_MTD_UBI_GLUEBI is not set +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_MUTEX_SPIN_ON_OWNER=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NET_FLOW_LIMIT=y +# CONFIG_NET_SCH_TAPRIO is not set +CONFIG_NET_VENDOR_GOOGLE=y +CONFIG_NET_VENDOR_PENSANDO=y +# CONFIG_NI_XGE_MANAGEMENT_ENET is not set +CONFIG_NR_CPUS=2 +# CONFIG_NULL_TTY is not set +CONFIG_NVMEM=y +CONFIG_NVMEM_SYSFS=y +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_KOBJ=y +CONFIG_OF_MDIO=y +CONFIG_OF_NET=y +CONFIG_OF_RESERVED_MEM=y +CONFIG_OLD_SIGACTION=y +CONFIG_OLD_SIGSUSPEND3=y +CONFIG_OUTER_CACHE=y +CONFIG_OUTER_CACHE_SYNC=y +# CONFIG_PACKING is not set +CONFIG_PADATA=y +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PCI=y +CONFIG_PCIE_IPROC=y +CONFIG_PCIE_IPROC_BCMA=y +# CONFIG_PCIE_IPROC_PLATFORM is not set +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_DOMAINS_GENERIC=y +# CONFIG_PCI_V3_SEMI is not set +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PGTABLE_LEVELS=2 +CONFIG_PHYLIB=y +# CONFIG_PHY_BCM_NS_USB2 is not set +# CONFIG_PHY_BCM_NS_USB3 is not set +# CONFIG_PHY_BCM_SR_PCIE is not set +CONFIG_PHY_BCM_SR_USB=y +# CONFIG_PHY_BRCM_SATA is not set +# CONFIG_PHY_CADENCE_DP is not set +# CONFIG_PHY_CADENCE_DPHY is not set +# CONFIG_PHY_FSL_IMX8MQ_USB is not set +# CONFIG_PHY_MIXEL_MIPI_DPHY is not set +# CONFIG_PHY_NS2_USB_DRD is not set +# CONFIG_PHY_OCELOT_SERDES is not set +CONFIG_PINCTRL=y +# CONFIG_PINCTRL_IPROC_GPIO is not set +CONFIG_PINCTRL_NS=y +# CONFIG_PINCTRL_NS2_MUX is not set +# CONFIG_PINCTRL_OCELOT is not set +# CONFIG_PL310_ERRATA_588369 is not set +# CONFIG_PL310_ERRATA_727915 is not set +# CONFIG_PL310_ERRATA_753970 is not set +# CONFIG_PL310_ERRATA_769419 is not set +# CONFIG_PRINTK_CALLER is not set +# CONFIG_PSI is not set +# CONFIG_PVPANIC is not set +# CONFIG_RANDOM_TRUST_BOOTLOADER is not set +CONFIG_RATIONAL=y +CONFIG_RCU_NEED_SEGCBLIST=y +CONFIG_RCU_STALL_COMMON=y +# CONFIG_REED_SOLOMON_TEST is not set +CONFIG_REFCOUNT_FULL=y +CONFIG_REGMAP=y +CONFIG_REGMAP_MMIO=y +CONFIG_RFS_ACCEL=y +CONFIG_RPS=y +CONFIG_RWSEM_SPIN_ON_OWNER=y +CONFIG_SERIAL_8250_FSL=y +# CONFIG_SERIAL_AMBA_PL011 is not set +# CONFIG_SERIAL_FSL_LINFLEXUART is not set +CONFIG_SERIAL_MCTRL_GPIO=y +CONFIG_SERIAL_OF_PLATFORM=y +# CONFIG_SERIAL_SIFIVE is not set +CONFIG_SGL_ALLOC=y +# CONFIG_SHUFFLE_PAGE_ALLOCATOR is not set +CONFIG_SMP=y +CONFIG_SMP_ON_UP=y +CONFIG_SPARSE_IRQ=y +CONFIG_SPI=y +CONFIG_SPI_BCM_QSPI=y +CONFIG_SPI_BITBANG=y +CONFIG_SPI_GPIO=y +CONFIG_SPI_MASTER=y +CONFIG_SPI_MEM=y +# CONFIG_SPI_MTK_QUADSPI is not set +CONFIG_SRCU=y +CONFIG_SWCONFIG=y +CONFIG_SWCONFIG_B53=y +# CONFIG_SWCONFIG_B53_MMAP_DRIVER is not set +CONFIG_SWCONFIG_B53_PHY_DRIVER=y +CONFIG_SWCONFIG_B53_PHY_FIXUP=y +CONFIG_SWCONFIG_B53_SRAB_DRIVER=y +CONFIG_SWPHY=y +CONFIG_SWP_EMULATE=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +# CONFIG_TEST_BLACKHOLE_DEV is not set +# CONFIG_TEST_MEMCAT_P is not set +# CONFIG_TEST_MEMINIT is not set +# CONFIG_TEST_STACKINIT is not set +# CONFIG_TEST_STRSCPY is not set +# CONFIG_TEST_VMALLOC is not set +# CONFIG_TEST_XARRAY is not set +CONFIG_THERMAL=y +CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y +CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 +CONFIG_THERMAL_GOV_STEP_WISE=y +CONFIG_THERMAL_OF=y +# CONFIG_THUMB2_KERNEL is not set +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_TIMER_OF=y +CONFIG_TIMER_PROBE=y +# CONFIG_TI_CPSW_PHY_SEL is not set +CONFIG_TREE_RCU=y +CONFIG_TREE_SRCU=y +# CONFIG_TRUSTED_FOUNDATIONS is not set +CONFIG_UBIFS_FS=y +# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_ZLIB=y +CONFIG_UBIFS_FS_ZSTD=y +CONFIG_UBSAN_ALIGNMENT=y +CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h" +# CONFIG_UNICODE is not set +CONFIG_UNIX_SCM=y +CONFIG_UNWINDER_ARM=y +# CONFIG_UNWINDER_FRAME_POINTER is not set +# CONFIG_USB_CONN_GPIO is not set +CONFIG_USB_SUPPORT=y +CONFIG_USE_OF=y +# CONFIG_VALIDATE_FS_PARSER is not set +# CONFIG_VFP is not set +CONFIG_WATCHDOG_CORE=y +CONFIG_WATCHDOG_OPEN_TIMEOUT=0 +# CONFIG_XILINX_SDFEC is not set +CONFIG_XPS=y +CONFIG_XXHASH=y +CONFIG_XZ_DEC_ARM=y +CONFIG_XZ_DEC_BCJ=y +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZLIB_DEFLATE=y +CONFIG_ZLIB_INFLATE=y +CONFIG_ZSTD_COMPRESS=y +CONFIG_ZSTD_DECOMPRESS=y diff --git a/target/linux/bcm53xx/image/Makefile b/target/linux/bcm53xx/image/Makefile index 6f509741ac..f438fd1208 100644 --- a/target/linux/bcm53xx/image/Makefile +++ b/target/linux/bcm53xx/image/Makefile @@ -385,7 +385,7 @@ define Device/tplink-archer-c5-v2 IMAGE/bin := append-rootfs | bcm53xx-tplink-safeloader TPLINK_BOARD := ARCHER-C5-V2 endef -TARGET_DEVICES += tplink-archer-c5-v2 +#TARGET_DEVICES += tplink-archer-c5-v2 define Device/tplink-archer-c9-v1 DEVICE_VENDOR := TP-LINK @@ -396,6 +396,6 @@ define Device/tplink-archer-c9-v1 IMAGE/bin := append-rootfs | bcm53xx-tplink-safeloader TPLINK_BOARD := ARCHERC9 endef -TARGET_DEVICES += tplink-archer-c9-v1 +#TARGET_DEVICES += tplink-archer-c9-v1 $(eval $(call BuildImage)) diff --git a/target/linux/bcm53xx/patches-5.4/130-ARM-dts-BCM5301X-Add-DT-for-Luxul-XWC-2000.patch b/target/linux/bcm53xx/patches-5.4/130-ARM-dts-BCM5301X-Add-DT-for-Luxul-XWC-2000.patch new file mode 100644 index 0000000000..beeeda7b95 --- /dev/null +++ b/target/linux/bcm53xx/patches-5.4/130-ARM-dts-BCM5301X-Add-DT-for-Luxul-XWC-2000.patch @@ -0,0 +1,80 @@ +From: Dan Haab +Date: Wed, 2 Oct 2019 09:57:26 -0600 +Subject: [PATCH] ARM: dts: BCM5301X: Add DT for Luxul XWC-2000 + +It's a simple network device based on BCM47094 with just a single +Ethernet port. + +Signed-off-by: Dan Haab +--- + arch/arm/boot/dts/Makefile | 1 + + arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts | 53 +++++++++++++++++++ + 2 files changed, 54 insertions(+) + create mode 100644 arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts + +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -111,6 +111,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ + bcm47094-luxul-abr-4500.dtb \ + bcm47094-luxul-xap-1610.dtb \ + bcm47094-luxul-xbr-4500.dtb \ ++ bcm47094-luxul-xwc-2000.dtb \ + bcm47094-luxul-xwr-3100.dtb \ + bcm47094-luxul-xwr-3150-v1.dtb \ + bcm47094-netgear-r8500.dtb \ +--- /dev/null ++++ b/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts +@@ -0,0 +1,53 @@ ++// SPDX-License-Identifier: GPL-2.0-or-later OR MIT ++/* ++ * Copyright 2019 Legrand AV Inc. ++ */ ++ ++/dts-v1/; ++ ++#include "bcm47094.dtsi" ++#include "bcm5301x-nand-cs0-bch8.dtsi" ++ ++/ { ++ compatible = "luxul,xwc-2000-v1", "brcm,bcm47094", "brcm,bcm4708"; ++ model = "Luxul XWC-2000 V1"; ++ ++ chosen { ++ bootargs = "earlycon"; ++ }; ++ ++ memory { ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x18000000>; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ ++ status { ++ label = "bcm53xx:green:status"; ++ gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "timer"; ++ }; ++ }; ++ ++ gpio-keys { ++ compatible = "gpio-keys"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ restart { ++ label = "Reset"; ++ linux,code = ; ++ gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++}; ++ ++&uart1 { ++ status = "okay"; ++}; ++ ++&spi_nor { ++ status = "okay"; ++}; diff --git a/target/linux/bcm53xx/patches-5.4/180-usb-xhci-add-support-for-performing-fake-doorbell.patch b/target/linux/bcm53xx/patches-5.4/180-usb-xhci-add-support-for-performing-fake-doorbell.patch new file mode 100644 index 0000000000..be7a52a936 --- /dev/null +++ b/target/linux/bcm53xx/patches-5.4/180-usb-xhci-add-support-for-performing-fake-doorbell.patch @@ -0,0 +1,143 @@ +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Sat, 1 Oct 2016 22:54:48 +0200 +Subject: [PATCH] usb: xhci: add support for performing fake doorbell + +Broadcom's Northstar XHCI controllers seem to need a special start +procedure to work correctly. There isn't any official documentation of +this, the problem is that controller doesn't detect any connected +devices with default setup. Moreover connecting USB device to controller +that doesn't run properly can cause SoC's watchdog issues. + +A workaround that was successfully tested on multiple devices is to +perform a fake doorbell. This patch adds code for doing this and enables +it on BCM4708 family. +--- + drivers/usb/host/xhci-plat.c | 6 +++++ + drivers/usb/host/xhci.c | 63 +++++++++++++++++++++++++++++++++++++++++--- + drivers/usb/host/xhci.h | 1 + + 3 files changed, 67 insertions(+), 3 deletions(-) + +Index: linux-5.4.11/drivers/usb/host/xhci-plat.c +=================================================================== +--- linux-5.4.11.orig/drivers/usb/host/xhci-plat.c ++++ linux-5.4.11/drivers/usb/host/xhci-plat.c +@@ -67,6 +67,8 @@ static int xhci_priv_resume_quirk(struct + static void xhci_plat_quirks(struct device *dev, struct xhci_hcd *xhci) + { + struct xhci_plat_priv *priv = xhci_to_priv(xhci); ++ struct platform_device*pdev = to_platform_device(dev); ++ struct device_node *node = pdev->dev.of_node; + + /* + * As of now platform drivers don't provide MSI support so we ensure +@@ -74,6 +76,9 @@ static void xhci_plat_quirks(struct devi + * dev struct in order to setup MSI + */ + xhci->quirks |= XHCI_PLAT | priv->quirks; ++ ++ if (node && of_machine_is_compatible("brcm,bcm4708")) ++ xhci->quirks |= XHCI_FAKE_DOORBELL; + } + + /* called during probe() after chip reset completes */ +Index: linux-5.4.11/drivers/usb/host/xhci.c +=================================================================== +--- linux-5.4.11.orig/drivers/usb/host/xhci.c ++++ linux-5.4.11/drivers/usb/host/xhci.c +@@ -156,6 +156,49 @@ int xhci_start(struct xhci_hcd *xhci) + return ret; + } + ++/** ++ * xhci_fake_doorbell - Perform a fake doorbell on a specified slot ++ * ++ * Some controllers require a fake doorbell to start correctly. Without that ++ * they simply don't detect any devices. ++ */ ++static int xhci_fake_doorbell(struct xhci_hcd *xhci, int slot_id) ++{ ++ u32 temp; ++ ++ /* Alloc a virt device for that slot */ ++ if (!xhci_alloc_virt_device(xhci, slot_id, NULL, GFP_NOIO)) { ++ xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n"); ++ return -ENOMEM; ++ } ++ ++ /* Ring fake doorbell for slot_id ep 0 */ ++ xhci_ring_ep_doorbell(xhci, slot_id, 0, 0); ++ usleep_range(1000, 1500); ++ ++ /* Read the status to check if HSE is set or not */ ++ temp = readl(&xhci->op_regs->status); ++ ++ /* Clear HSE if set */ ++ if (temp & STS_FATAL) { ++ xhci_dbg(xhci, "HSE problem detected, status: 0x%08x\n", temp); ++ temp &= ~0x1fff; ++ temp |= STS_FATAL; ++ writel(temp, &xhci->op_regs->status); ++ usleep_range(1000, 1500); ++ readl(&xhci->op_regs->status); ++ } ++ ++ /* Free virt device */ ++ xhci_free_virt_device(xhci, slot_id); ++ ++ /* We're done if controller is already running */ ++ if (readl(&xhci->op_regs->command) & CMD_RUN) ++ return 0; ++ ++ return xhci_start(xhci); ++} ++ + /* + * Reset a halted HC. + * +@@ -604,10 +647,20 @@ static int xhci_init(struct usb_hcd *hcd + + static int xhci_run_finished(struct xhci_hcd *xhci) + { +- if (xhci_start(xhci)) { +- xhci_halt(xhci); +- return -ENODEV; ++ int err; ++ ++ err = xhci_start(xhci); ++ if (err) { ++ err = -ENODEV; ++ goto err_halt; + } ++ ++ if (xhci->quirks & XHCI_FAKE_DOORBELL) { ++ err = xhci_fake_doorbell(xhci, 1); ++ if (err) ++ goto err_halt; ++ } ++ + xhci->shared_hcd->state = HC_STATE_RUNNING; + xhci->cmd_ring_state = CMD_RING_STATE_RUNNING; + +@@ -617,6 +670,10 @@ static int xhci_run_finished(struct xhci + xhci_dbg_trace(xhci, trace_xhci_dbg_init, + "Finished xhci_run for USB3 roothub"); + return 0; ++ ++err_halt: ++ xhci_halt(xhci); ++ return err; + } + + /* +Index: linux-5.4.11/drivers/usb/host/xhci.h +=================================================================== +--- linux-5.4.11.orig/drivers/usb/host/xhci.h ++++ linux-5.4.11/drivers/usb/host/xhci.h +@@ -1867,6 +1867,7 @@ struct xhci_hcd { + #define XHCI_DEFAULT_PM_RUNTIME_ALLOW BIT_ULL(33) + #define XHCI_RESET_PLL_ON_DISCONNECT BIT_ULL(34) + #define XHCI_SNPS_BROKEN_SUSPEND BIT_ULL(35) ++#define XHCI_FAKE_DOORBELL BIT_ULL(36) + + unsigned int num_active_eps; + unsigned int limit_active_eps; diff --git a/target/linux/bcm53xx/patches-5.4/300-ARM-BCM5301X-Disable-MMU-and-Dcache-during-decompres.patch b/target/linux/bcm53xx/patches-5.4/300-ARM-BCM5301X-Disable-MMU-and-Dcache-during-decompres.patch new file mode 100644 index 0000000000..034d5b52fc --- /dev/null +++ b/target/linux/bcm53xx/patches-5.4/300-ARM-BCM5301X-Disable-MMU-and-Dcache-during-decompres.patch @@ -0,0 +1,101 @@ +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Wed, 24 Sep 2014 22:14:07 +0200 +Subject: [PATCH] ARM: BCM5301X: Disable MMU and Dcache during decompression +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Broadcom devices have broken CFE (bootloader) that leaves hardware in an +invalid state. It causes problems with booting Linux. On Northstar +devices kernel was randomly hanging in ~25% of tries during early init. +Hangs used to happen at random places in the start_kernel. On BCM53573 +kernel doesn't even seem to start booting. + +To workaround this problem we need to do following very early: +1) Clear 2 following bits in the SCTLR register: +#define CR_M (1 << 0) /* MMU enable */ +#define CR_C (1 << 2) /* Dcache enable */ +2) Flush the whole D-cache +3) Disable L2 cache + +Unfortunately this patch is not upstreamable as it does above things +unconditionally. We can't check if we are running on Broadcom platform +in any safe way and doing such hacks with ARCH_MULTI_V7 is unacceptable +as it could break other devices support. + +Signed-off-by: Rafał Miłecki +--- + +--- a/arch/arm/boot/compressed/Makefile ++++ b/arch/arm/boot/compressed/Makefile +@@ -35,6 +35,11 @@ ifeq ($(CONFIG_ARCH_ACORN),y) + OBJS += ll_char_wr.o font.o + endif + ++ifeq ($(CONFIG_ARCH_BCM_5301X),y) ++OBJS += head-bcm_5301x-mpcore.o ++OBJS += cache-v7-min.o ++endif ++ + ifeq ($(CONFIG_ARCH_SA1100),y) + OBJS += head-sa1100.o + endif +--- /dev/null ++++ b/arch/arm/boot/compressed/head-bcm_5301x-mpcore.S +@@ -0,0 +1,37 @@ ++/* ++ * ++ * Platform specific tweaks. This is merged into head.S by the linker. ++ * ++ */ ++ ++#include ++#include ++#include ++ ++ .section ".start", "ax" ++ ++/* ++ * This code section is spliced into the head code by the linker ++ */ ++ ++__plat_uncompress_start: ++ ++ @ Preserve r8/r7 i.e. kernel entry values ++ mov r12, r8 ++ ++ @ Clear MMU enable and Dcache enable bits ++ mrc p15, 0, r0, c1, c0, 0 @ Read SCTLR ++ bic r0, #CR_C|CR_M ++ mcr p15, 0, r0, c1, c0, 0 @ Write SCTLR ++ nop ++ ++ @ Call the cache invalidation routine ++ bl v7_flush_dcache_all ++ nop ++ mov r0,#0 ++ ldr r3, =0x19022000 @ L2 cache controller, control reg ++ str r0, [r3, #0x100] @ Disable L2 cache ++ nop ++ ++ @ Restore ++ mov r8, r12 +--- a/arch/arm/boot/compressed/cache-v7-min.S ++++ b/arch/arm/boot/compressed/cache-v7-min.S +@@ -12,6 +12,7 @@ + + #include + #include ++#include + + __INIT + +@@ -63,7 +64,7 @@ loop2: + ARM( orr r11, r11, r9, lsl r2 ) @ factor index number into r11 + THUMB( lsl r6, r9, r2 ) + THUMB( orr r11, r11, r6 ) @ factor index number into r11 +- mcr p15, 0, r11, c7, c14, 2 @ clean & invalidate by set/way ++ mcr p15, 0, r11, c7, c6, 2 @ clean & invalidate by set/way + subs r9, r9, #1 @ decrement the index + bge loop2 + subs r4, r4, #1 @ decrement the way diff --git a/target/linux/bcm53xx/patches-5.4/302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch b/target/linux/bcm53xx/patches-5.4/302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch new file mode 100644 index 0000000000..d1d287588c --- /dev/null +++ b/target/linux/bcm53xx/patches-5.4/302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch @@ -0,0 +1,31 @@ +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Subject: [PATCH] ARM: dts: BCM5301X: Update Northstar pinctrl binding +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + +--- a/arch/arm/boot/dts/bcm5301x.dtsi ++++ b/arch/arm/boot/dts/bcm5301x.dtsi +@@ -400,16 +400,12 @@ + #size-cells = <1>; + + cru@100 { +- compatible = "simple-bus"; ++ compatible = "syscon", "simple-mfd"; + reg = <0x100 0x1a4>; +- ranges; +- #address-cells = <1>; +- #size-cells = <1>; + +- pin-controller@1c0 { ++ pinctrl { + compatible = "brcm,bcm4708-pinmux"; +- reg = <0x1c0 0x24>; +- reg-names = "cru_gpio_control"; ++ offset = <0xc0>; + + spi-pins { + groups = "spi_grp"; diff --git a/target/linux/bcm53xx/patches-5.4/310-ARM-BCM5301X-Add-DT-for-Netgear-R7900.patch b/target/linux/bcm53xx/patches-5.4/310-ARM-BCM5301X-Add-DT-for-Netgear-R7900.patch new file mode 100644 index 0000000000..fca2b88ed8 --- /dev/null +++ b/target/linux/bcm53xx/patches-5.4/310-ARM-BCM5301X-Add-DT-for-Netgear-R7900.patch @@ -0,0 +1,64 @@ +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Subject: [PATCH] ARM: BCM5301X: Add DT for Netgear R7900 +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -104,6 +104,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ + bcm4709-buffalo-wxr-1900dhp.dtb \ + bcm4709-linksys-ea9200.dtb \ + bcm4709-netgear-r7000.dtb \ ++ bcm4709-netgear-r7900.dtb \ + bcm4709-netgear-r8000.dtb \ + bcm4709-tplink-archer-c9-v1.dtb \ + bcm47094-dlink-dir-885l.dtb \ +--- /dev/null ++++ b/arch/arm/boot/dts/bcm4709-netgear-r7900.dts +@@ -0,0 +1,42 @@ ++/* ++ * Broadcom BCM470X / BCM5301X ARM platform code. ++ * DTS for Netgear R7900 ++ * ++ * Copyright (C) 2016 Rafał Miłecki ++ * ++ * Licensed under the GNU/GPL. See COPYING for details. ++ */ ++ ++/dts-v1/; ++ ++#include "bcm4709.dtsi" ++#include "bcm5301x-nand-cs0-bch8.dtsi" ++ ++/ { ++ compatible = "netgear,r7900", "brcm,bcm4709", "brcm,bcm4708"; ++ model = "Netgear R7900"; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200"; ++ }; ++ ++ memory { ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; ++ }; ++ ++ axi@18000000 { ++ usb3@23000 { ++ reg = <0x00023000 0x1000>; ++ ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; diff --git a/target/linux/bcm53xx/patches-5.4/311-ARM-BCM5301X-Add-power-button-for-Buffalo-WZR-1750DHP.patch b/target/linux/bcm53xx/patches-5.4/311-ARM-BCM5301X-Add-power-button-for-Buffalo-WZR-1750DHP.patch new file mode 100644 index 0000000000..5ebc7f89f2 --- /dev/null +++ b/target/linux/bcm53xx/patches-5.4/311-ARM-BCM5301X-Add-power-button-for-Buffalo-WZR-1750DHP.patch @@ -0,0 +1,20 @@ +From: Felix Fietkau +Subject: [PATCH] ARM: BCM5301X: Add power button for Buffalo WZR-1750DHP + +Signed-off-by: Felix Fietkau +--- +--- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts ++++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts +@@ -101,6 +101,12 @@ + #address-cells = <1>; + #size-cells = <0>; + ++ power { ++ label = "Power"; ++ linux,code = ; ++ gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>; ++ }; ++ + restart { + label = "Reset"; + linux,code = ; diff --git a/target/linux/bcm53xx/patches-5.4/320-ARM-dts-BCM5301X-Add-serial-to-the-bootargs.patch b/target/linux/bcm53xx/patches-5.4/320-ARM-dts-BCM5301X-Add-serial-to-the-bootargs.patch new file mode 100644 index 0000000000..2f3e287d4e --- /dev/null +++ b/target/linux/bcm53xx/patches-5.4/320-ARM-dts-BCM5301X-Add-serial-to-the-bootargs.patch @@ -0,0 +1,134 @@ +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Subject: [PATCH] ARM: dts: BCM5301X: Add serial= to the bootargs +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +It's enough to have proper stdout-path for getting serial working but +for some reason LEDE doesn't offer "Please press Enter to activate this +console." unless ttyS0 is specified. + +This is a workaround to get serial working in LEDE. + +Signed-off-by: Rafał Miłecki +--- + +Index: linux-5.4.11/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts +=================================================================== +--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts ++++ linux-5.4.11/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts +@@ -12,7 +12,7 @@ + model = "TP-LINK Archer C5 V2"; + + chosen { +- bootargs = "earlycon"; ++ bootargs = "console=ttyS0,115200 earlycon"; + }; + + memory@0 { +Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts +=================================================================== +--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts ++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts +@@ -13,7 +13,7 @@ + model = "Luxul ABR-4500 V1"; + + chosen { +- bootargs = "earlycon"; ++ bootargs = "console=ttyS0,115200 earlycon"; + }; + + memory@0 { +Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts +=================================================================== +--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts ++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts +@@ -13,7 +13,7 @@ + model = "Luxul XBR-4500 V1"; + + chosen { +- bootargs = "earlycon"; ++ bootargs = "console=ttyS0,115200 earlycon"; + }; + + memory@0 { +Index: linux-5.4.11/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts +=================================================================== +--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts ++++ linux-5.4.11/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts +@@ -12,7 +12,7 @@ + model = "Luxul XAP-1440 V1"; + + chosen { +- bootargs = "earlycon"; ++ bootargs = "console=ttyS0,115200 earlycon"; + }; + + memory@0 { +Index: linux-5.4.11/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts +=================================================================== +--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts ++++ linux-5.4.11/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts +@@ -12,7 +12,7 @@ + model = "Luxul XAP-810 V1"; + + chosen { +- bootargs = "earlycon"; ++ bootargs = "console=ttyS0,115200 earlycon"; + }; + + memory@0 { +Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts +=================================================================== +--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts ++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts +@@ -12,7 +12,7 @@ + model = "Luxul XAP-1610 V1"; + + chosen { +- bootargs = "earlycon"; ++ bootargs = "console=ttyS0,115200 earlycon"; + }; + + memory@0 { +Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts +=================================================================== +--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts ++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts +@@ -13,7 +13,7 @@ + model = "Luxul XWR-3150 V1"; + + chosen { +- bootargs = "earlycon"; ++ bootargs = "console=ttyS0,115200 earlycon"; + }; + + memory@0 { +Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-phicomm-k3.dts +=================================================================== +--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-phicomm-k3.dts ++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-phicomm-k3.dts +@@ -13,6 +13,10 @@ + compatible = "phicomm,k3", "brcm,bcm47094", "brcm,bcm4708"; + model = "Phicomm K3"; + ++ chosen { ++ bootargs = "console=ttyS0,115200"; ++ }; ++ + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x08000000 +Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts +=================================================================== +--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts ++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts +@@ -13,7 +13,7 @@ + model = "Luxul XWC-2000 V1"; + + chosen { +- bootargs = "earlycon"; ++ bootargs = "console=ttyS0,115200 earlycon"; + }; + + memory { diff --git a/target/linux/bcm53xx/patches-5.4/321-ARM-dts-BCM5301X-Describe-partition-formats.patch b/target/linux/bcm53xx/patches-5.4/321-ARM-dts-BCM5301X-Describe-partition-formats.patch new file mode 100644 index 0000000000..66ae6dca33 --- /dev/null +++ b/target/linux/bcm53xx/patches-5.4/321-ARM-dts-BCM5301X-Describe-partition-formats.patch @@ -0,0 +1,25 @@ +From 7166207bd1d8c46d09d640d46afc685df9bb9083 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Thu, 22 Nov 2018 09:21:49 +0100 +Subject: [PATCH] ARM: dts: BCM5301X: Describe partition formats +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +It's needed by OpenWrt for custom partitioning. + +Signed-off-by: Rafał Miłecki +--- + arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts | 1 + + 1 file changed, 1 insertion(+) + +--- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts ++++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts +@@ -34,6 +34,7 @@ + partition@0 { + label = "firmware"; + reg = <0x00000000 0x08000000>; ++ compatible = "seama"; + }; + }; + }; diff --git a/target/linux/bcm53xx/patches-5.4/500-UBI-Detect-EOF-mark-and-erase-all-remaining-blocks.patch b/target/linux/bcm53xx/patches-5.4/500-UBI-Detect-EOF-mark-and-erase-all-remaining-blocks.patch new file mode 100644 index 0000000000..6d7a45f7ba --- /dev/null +++ b/target/linux/bcm53xx/patches-5.4/500-UBI-Detect-EOF-mark-and-erase-all-remaining-blocks.patch @@ -0,0 +1,59 @@ +From 2a2af518266a29323cf30c3f9ba9ef2ceb1dd84b Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Thu, 16 Oct 2014 20:52:16 +0200 +Subject: [PATCH] UBI: Detect EOF mark and erase all remaining blocks +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + drivers/mtd/ubi/attach.c | 5 +++++ + drivers/mtd/ubi/io.c | 4 ++++ + drivers/mtd/ubi/ubi.h | 1 + + 3 files changed, 10 insertions(+) + +--- a/drivers/mtd/ubi/attach.c ++++ b/drivers/mtd/ubi/attach.c +@@ -95,6 +95,9 @@ static int self_check_ai(struct ubi_devi + #define AV_ADD BIT(1) + #define AV_FIND_OR_ADD (AV_FIND | AV_ADD) + ++/* Set on finding block with 0xdeadc0de, indicates erasing all blocks behind */ ++bool erase_all_next; ++ + /** + * find_or_add_av - internal function to find a volume, add a volume or do + * both (find and add if missing). +@@ -1592,6 +1595,8 @@ int ubi_attach(struct ubi_device *ubi, i + if (!ai) + return -ENOMEM; + ++ erase_all_next = false; ++ + #ifdef CONFIG_MTD_UBI_FASTMAP + /* On small flash devices we disable fastmap in any case. */ + if ((int)mtd_div_by_eb(ubi->mtd->size, ubi->mtd) <= UBI_FM_MAX_START) { +--- a/drivers/mtd/ubi/io.c ++++ b/drivers/mtd/ubi/io.c +@@ -723,6 +723,10 @@ int ubi_io_read_ec_hdr(struct ubi_device + } + + magic = be32_to_cpu(ec_hdr->magic); ++ if (magic == 0xdeadc0de) ++ erase_all_next = true; ++ if (erase_all_next) ++ return read_err ? UBI_IO_FF_BITFLIPS : UBI_IO_FF; + if (magic != UBI_EC_HDR_MAGIC) { + if (mtd_is_eccerr(read_err)) + return UBI_IO_BAD_HDR_EBADMSG; +--- a/drivers/mtd/ubi/ubi.h ++++ b/drivers/mtd/ubi/ubi.h +@@ -833,6 +833,7 @@ extern struct mutex ubi_devices_mutex; + extern struct blocking_notifier_head ubi_notifiers; + + /* attach.c */ ++extern bool erase_all_next; + struct ubi_ainf_peb *ubi_alloc_aeb(struct ubi_attach_info *ai, int pnum, + int ec); + void ubi_free_aeb(struct ubi_attach_info *ai, struct ubi_ainf_peb *aeb); diff --git a/target/linux/bcm53xx/patches-5.4/700-b53-add-hacky-CPU-port-fixes-for-devices-not-using-p.patch b/target/linux/bcm53xx/patches-5.4/700-b53-add-hacky-CPU-port-fixes-for-devices-not-using-p.patch new file mode 100644 index 0000000000..91bb4fae11 --- /dev/null +++ b/target/linux/bcm53xx/patches-5.4/700-b53-add-hacky-CPU-port-fixes-for-devices-not-using-p.patch @@ -0,0 +1,52 @@ +From 4abdde3ad6bc0b3b157c4bf6ec0bf139d11d07e8 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Wed, 13 May 2015 14:13:28 +0200 +Subject: [PATCH] b53: add hacky CPU port fixes for devices not using port 5 +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + drivers/net/phy/b53/b53_common.c | 6 ++++++ + 1 file changed, 6 insertions(+) + +--- a/drivers/net/phy/b53/b53_common.c ++++ b/drivers/net/phy/b53/b53_common.c +@@ -28,6 +28,7 @@ + #include + #include + #include ++#include + + #include "b53_regs.h" + #include "b53_priv.h" +@@ -1579,6 +1580,28 @@ static int b53_switch_init(struct b53_de + return ret; + } + ++ /* Set correct CPU port */ ++ if (of_machine_is_compatible("asus,rt-ac87u")) ++ sw_dev->cpu_port = 7; ++ else if (of_machine_is_compatible("netgear,r7900")) ++ sw_dev->cpu_port = 8; ++ else if (of_machine_is_compatible("netgear,r8000")) ++ sw_dev->cpu_port = 8; ++ else if (of_machine_is_compatible("netgear,r8500")) ++ sw_dev->cpu_port = 8; ++ ++ /* Enable extra ports */ ++ if (of_machine_is_compatible("tenda,ac9")) ++ dev->enabled_ports |= BIT(5); ++ ++ /* ++ * Workaround for devices using port 8 (connected to the 3rd iface). ++ * For some reason it doesn't work (no packets on eth2). ++ */ ++ if (of_machine_is_compatible("netgear,r7900") || ++ of_machine_is_compatible("netgear,r8000")) ++ sw_dev->cpu_port = 5; ++ + dev->enabled_ports |= BIT(sw_dev->cpu_port); + sw_dev->ports = fls(dev->enabled_ports); + diff --git a/target/linux/bcm53xx/patches-5.4/905-BCM53573-minor-hacks.patch b/target/linux/bcm53xx/patches-5.4/905-BCM53573-minor-hacks.patch new file mode 100644 index 0000000000..470b17a5ff --- /dev/null +++ b/target/linux/bcm53xx/patches-5.4/905-BCM53573-minor-hacks.patch @@ -0,0 +1,80 @@ +From 6f1c62440eb6846cb8045d7a5480ec7bbe47c96f Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Mon, 15 Aug 2016 10:30:41 +0200 +Subject: [PATCH] BCM53573 minor hacks +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + +--- a/arch/arm/boot/dts/bcm53573.dtsi ++++ b/arch/arm/boot/dts/bcm53573.dtsi +@@ -53,6 +53,7 @@ + , + , + ; ++ clocks = <&ilp>; + }; + + clocks { +--- a/drivers/bcma/main.c ++++ b/drivers/bcma/main.c +@@ -330,14 +330,6 @@ static int bcma_register_devices(struct + } + #endif + +-#ifdef CONFIG_BCMA_SFLASH +- if (bus->drv_cc.sflash.present) { +- err = platform_device_register(&bcma_sflash_dev); +- if (err) +- bcma_err(bus, "Error registering serial flash\n"); +- } +-#endif +- + #ifdef CONFIG_BCMA_NFLASH + if (bus->drv_cc.nflash.present) { + err = platform_device_register(&bcma_nflash_dev); +@@ -415,6 +407,14 @@ int bcma_bus_register(struct bcma_bus *b + bcma_register_core(bus, core); + } + ++#ifdef CONFIG_BCMA_SFLASH ++ if (bus->drv_cc.sflash.present) { ++ err = platform_device_register(&bcma_sflash_dev); ++ if (err) ++ bcma_err(bus, "Error registering serial flash\n"); ++ } ++#endif ++ + /* Try to get SPROM */ + err = bcma_sprom_get(bus); + if (err == -ENOENT) { +--- a/drivers/clocksource/arm_arch_timer.c ++++ b/drivers/clocksource/arm_arch_timer.c +@@ -17,6 +17,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -919,6 +920,16 @@ static void arch_timer_of_configure_rate + if (of_property_read_u32(np, "clock-frequency", &arch_timer_rate)) + arch_timer_rate = rate; + ++ /* Get clk rate through clk driver if present */ ++ if (!arch_timer_rate) { ++ struct clk *clk = of_clk_get(np, 0); ++ ++ if (!IS_ERR(clk)) { ++ if (!clk_prepare_enable(clk)) ++ arch_timer_rate = clk_get_rate(clk); ++ } ++ } ++ + /* Check the timer frequency. */ + if (arch_timer_rate == 0) + pr_warn("frequency not available\n");