From: Jeff Kletsky Date: Sun, 2 Jun 2019 00:51:17 +0000 (-0700) Subject: ath79: GL-AR300M: provide NAND support; increase to 4 MB kernel X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=55e6c903ae20bd8e694f4626166766e59602f87c;p=openwrt%2Fstaging%2Fdedeckeh.git ath79: GL-AR300M: provide NAND support; increase to 4 MB kernel The GL.iNet GL-AR300M has been supported by the ar71xx and ath79 platforms with access to its 16 MB NOR flash, but not its 128 MB SPI NAND flash. This commit provides support for the NAND through the upstream SPI-NAND framework. Devices with both NOR and NAND flash can support independent firmware on each, with U-Boot able to boot from either. The OEM U-Boot will fall back to the NOR firmware after three "unsuccessful" boots. The family of GL-AR300M devices on the ath79 platform now includes: * glinet,gl-ar300m-lite "generic" target, NOR-only board * glinet,gl-ar300m-nand "nand" target * glinet,gl-ar300m-nor "nand" target (NAND-aware) NB: This commit increases the kernel size from 2 MB to 4 MB "Force-less" sysupgrade is presently supported from the current versions of following NOR-based firmwre images to the version of glinet,gl-ar300m-nor firmware produced by this commit: * gl-ar300m -- OEM v3 NOR ar71xx (openwrt-ar300m16-*.bin) * gl-ar300m -- OpenWrt 18.06 ar71xx * gl-ar300m -- OpenWrt 19.07 ar71xx Other upgrades to these images should be performed through U-Boot. The GL-AR300M OEM U-Boot allows upload and flashing of either NOR firmware (sysupgrade.bin) or NAND firmware (factory.img) through its HTTP-based GUI. Serial connectivity is not required. The glinet,gl-ar300m-nand and glinet,gl-ar300m-nor images generated after this commit should safely flash each other using sysupgrade. The boot counter is implemented by the OEM using u-boot-env. At this time, it does not appear that the switch on the side of the unit can be used to select NOR vs. NAND boot and the fail-over is only from NAND to NOR. To save flash wear, it is only reset when running the glinet,gl-ar300m-nand firmware. NAND-specific base-files are used to remove impact on existing generic and tiny targets. As there is now no "generic" build appropriate for the GL-AR300M16, (or for users of the GL-AR300M that do not need access to NAND) it will be introduced in a subsequent commit. Note: `mtd_get_mac_binary art 0x6` does not return the proper MAC and the GL.iNet source indicates that only the 0x0 offset is valid The ar71xx targets are unmodified. Signed-off-by: Jeff Kletsky --- diff --git a/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-lite.dts b/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-lite.dts index 148d017540..ed00cdb585 100644 --- a/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-lite.dts +++ b/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-lite.dts @@ -1,3 +1,5 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + /dts-v1/; #include "qca9531_glinet_gl-ar300m.dtsi" @@ -7,6 +9,8 @@ model = "GL.iNet GL-AR300M-Lite"; }; +/delete-node/ &nand_flash; + // "Disable" unpopulated GMAC1 ð1 { diff --git a/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-nand.dts b/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-nand.dts index 26c30f2b72..00f9f5c82d 100644 --- a/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-nand.dts +++ b/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-nand.dts @@ -1,3 +1,5 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + /dts-v1/; #include "qca9531_glinet_gl-ar300m.dtsi" @@ -7,28 +9,10 @@ model = "GL.iNet GL-AR300M (NAND)"; }; -&spi { - num-cs = <1>; - - flash@1 { - compatible = "spinand,mt29f"; - reg = <1>; - spi-max-frequency = <25000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "kernel"; - reg = <0x000000 0x0200000>; - }; +&nand_kernel { + label = "kernel"; +}; - partition@1 { - label = "ubi"; - reg = <0x200000 0x7e00000>; - }; - }; - }; +&nand_ubi { + label = "ubi"; }; diff --git a/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-nor.dts b/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-nor.dts index 22e5ae4e74..34f48f5f61 100644 --- a/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-nor.dts +++ b/target/linux/ath79/dts/qca9531_glinet_gl-ar300m-nor.dts @@ -6,3 +6,8 @@ compatible = "glinet,gl-ar300m-nor", "qca,qca9531"; model = "GL.iNet GL-AR300M (NOR)"; }; + +&nor_firmware { + compatible = "denx,uimage"; + label = "firmware"; +}; diff --git a/target/linux/ath79/dts/qca9531_glinet_gl-ar300m.dtsi b/target/linux/ath79/dts/qca9531_glinet_gl-ar300m.dtsi index 78961bf71b..72bc2a6466 100644 --- a/target/linux/ath79/dts/qca9531_glinet_gl-ar300m.dtsi +++ b/target/linux/ath79/dts/qca9531_glinet_gl-ar300m.dtsi @@ -42,7 +42,7 @@ leds { compatible = "gpio-leds"; - // Colors from non-Lite versions + // Colors for non-Lite versions led_status: status { label = "gl-ar300m:green:status"; @@ -75,10 +75,12 @@ &spi { status = "okay"; - num-cs = <0>; + + num-cs = <2>; + cs-gpios = <0>, <0>; flash@0 { - compatible = "winbond,w25q128", "jedec,spi-nor"; + compatible = "jedec,spi-nor"; reg = <0>; spi-max-frequency = <25000000>; @@ -93,24 +95,45 @@ read-only; }; - partition@1 { + partition@40000 { label = "u-boot-env"; reg = <0x040000 0x010000>; }; - partition@2 { - compatible = "denx,uimage"; - label = "firmware"; + nor_firmware: partition@50000 { + label = "nor_firmware"; reg = <0x050000 0xfa0000>; }; - art: partition@3 { + art: partition@ff0000 { label = "art"; reg = <0xff0000 0x010000>; read-only; }; }; }; + + nand_flash: flash@1 { + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + nand_kernel: partition@0 { + label = "nand_kernel"; + reg = <0x000000 0x400000>; + }; + + nand_ubi: partition@400000 { + label = "nand_ubi"; + reg = <0x400000 0x7c00000>; + }; + }; + }; }; &uart { diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index de2c8e9197..4ab504654e 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -94,9 +94,6 @@ glinet,gl-ar150) ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1" ucidef_set_led_switch "lan" "LAN" "$boardname:green:lan" "switch0" "0x02" ;; -glinet,gl-ar300m-nor) - ucidef_set_led_netdev "lan" "LAN" "gl-ar300m:green:lan" "eth0" - ;; glinet,gl-ar300m-lite) ucidef_set_led_netdev "lan" "LAN" "gl-ar300m-lite:green:lan" "eth0" ;; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 70631c20d0..011bb41262 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -562,12 +562,6 @@ define Device/glinet_gl-ar300m-lite endef TARGET_DEVICES += glinet_gl-ar300m-lite -define Device/glinet_gl-ar300m-nor - $(Device/glinet_gl-ar300m-common-nor) - DEVICE_MODEL := GL-AR300M -endef -TARGET_DEVICES += glinet_gl-ar300m-nor - define Device/glinet_gl-ar750 ATH_SOC := qca9531 DEVICE_VENDOR := GL.iNet diff --git a/target/linux/ath79/image/nand.mk b/target/linux/ath79/image/nand.mk index ef6b607002..f9961840f0 100644 --- a/target/linux/ath79/image/nand.mk +++ b/target/linux/ath79/image/nand.mk @@ -45,22 +45,36 @@ define Device/aerohive_hiveap-121 endef TARGET_DEVICES += aerohive_hiveap-121 -define Device/glinet_gl-ar300m-nand +define Device/glinet_gl-ar300m-common-nand ATH_SOC := qca9531 DEVICE_VENDOR := GL.iNet DEVICE_MODEL := GL-AR300M + DEVICE_PACKAGES := kmod-usb2 + KERNEL_SIZE := 4096k + IMAGE_SIZE := 16000k + PAGESIZE := 2048 + VID_HDR_OFFSET := 2048 +endef + +define Device/glinet_gl-ar300m-nand + $(Device/glinet_gl-ar300m-common-nand) DEVICE_VARIANT := NAND - DEVICE_PACKAGES := kmod-usb2 kmod-usb-storage kmod-usb-ledtrig-usbport - KERNEL_SIZE := 2048k BLOCKSIZE := 128k - PAGESIZE := 2048 - VID_HDR_OFFSET := 512 - IMAGES += factory.ubi - IMAGE/sysupgrade.bin := sysupgrade-tar - IMAGE/factory.ubi := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi + IMAGES += factory.img + IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + SUPPORTED_DEVICES += glinet,gl-ar300m-nor endef TARGET_DEVICES += glinet_gl-ar300m-nand +define Device/glinet_gl-ar300m-nor + $(Device/glinet_gl-ar300m-common-nand) + DEVICE_VARIANT := NOR + BLOCKSIZE := 64k + SUPPORTED_DEVICES += glinet,gl-ar300m-nand gl-ar300m +endef +TARGET_DEVICES += glinet_gl-ar300m-nor + # fake rootfs is mandatory, pad-offset 129 equals (2 * uimage_header + 0xff) define Device/netgear_ath79_nand DEVICE_VENDOR := NETGEAR diff --git a/target/linux/ath79/nand/base-files/etc/board.d/01_leds b/target/linux/ath79/nand/base-files/etc/board.d/01_leds index f851b3d886..f58527d87e 100755 --- a/target/linux/ath79/nand/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/nand/base-files/etc/board.d/01_leds @@ -8,7 +8,8 @@ board=$(board_name) boardname="${board##*,}" case "$board" in -glinet,gl-ar300m-nand) +glinet,gl-ar300m-nand|\ +glinet,gl-ar300m-nor) ucidef_set_led_netdev "lan" "LAN" "gl-ar300m:green:lan" "eth0" ;; netgear,wndr4300) diff --git a/target/linux/ath79/nand/base-files/etc/init.d/bootcount b/target/linux/ath79/nand/base-files/etc/init.d/bootcount new file mode 100755 index 0000000000..c82386b55f --- /dev/null +++ b/target/linux/ath79/nand/base-files/etc/init.d/bootcount @@ -0,0 +1,13 @@ +#!/bin/sh /etc/rc.common + +# SPDX-License-Identifier: GPL-2.0 + +START=99 + +boot() { + case $(board_name) in + glinet,gl-ar300m-nand) + fw_setenv bootcount 0 + ;; + esac +} diff --git a/target/linux/ath79/nand/base-files/lib/upgrade/glinet.sh b/target/linux/ath79/nand/base-files/lib/upgrade/glinet.sh new file mode 100644 index 0000000000..86729f8f2a --- /dev/null +++ b/target/linux/ath79/nand/base-files/lib/upgrade/glinet.sh @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: GPL-2.0 +# +# Copyright (C) 2019 Jeff Kletsky +# + +glinet_using_boot_dev_switch() { + if [ "$(fw_printenv -n boot_dev 2>/dev/null)" = "on" ] ; then + >&2 echo "NOTE: boot_dev=on; use switch to control boot partition" + true + else + false + fi +} + +glinet_set_next_boot_nand() { + mkdir -p /var/lock + ! glinet_using_boot_dev_switch && \ + fw_setenv bootcount 0 && \ + >&2 echo "Next boot set for NAND" +} + +glinet_set_next_boot_nor() { + mkdir -p /var/lock + ! glinet_using_boot_dev_switch && \ + fw_setenv bootcount 3 && \ + >&2 echo "Next boot set for NOR" +} + +glinet_nand_nor_do_upgrade() { + set_next_boot_nand() { glinet_set_next_boot_nand; } + set_next_boot_nor() { glinet_set_next_boot_nor; } + nand_nor_do_upgrade "$1" +} + +nand_nor_do_upgrade() { + local upgrade_file="$1" + + local pn + local found="" + local err + + case "$(get_magic_long "$upgrade_file")" in + + "27051956") # U-Boot Image Magic + + for pn in "nor_${PART_NAME}" "$PART_NAME" ; do # firmware + if [ "$(find_mtd_index "$pn")" ] ; then + PART_NAME="$pn" + found="yes" + break + fi + done + if [ "$found" = "yes" ] ; then + >&2 echo "Running NOR upgrade" + default_do_upgrade "$upgrade_file" + # At this time, default_do_upgrade() exits on error + type set_next_boot_nor >/dev/null && set_next_boot_nor + else + >&2 echo "ERROR: UPGRADE FAILED: Unable to locate '$PART_NAME' or 'nor_${PART_NAME}'" + exit 1 + fi + ;; + + *) # otherwise a file that nand_do_upgrade can process + + for pn in "nand_${CI_KERNPART}" "$CI_KERNPART" ; do # kernel + if [ "$(find_mtd_index "$pn")" ] ; then + CI_KERNPART="$pn" + break + fi + done + for pn in "nand_${CI_UBIPART}" "$CI_UBIPART" ; do # ubi + if [ "$(find_mtd_index "$pn")" ] ; then + CI_UBIPART="$pn" + break + fi + done + for pn in "nand_${CI_ROOTPART}" "$CI_ROOTPART" ; do #rootfs + if [ "$(find_mtd_index "$pn")" ] ; then + CI_ROOTPART="$pn" + break + fi + done + >&2 echo "Running NAND upgrade" + # TODO: change order when NAND upgrade offers return + type set_next_boot_nand >/dev/null && set_next_boot_nand + nand_do_upgrade "$upgrade_file" + ;; + esac +} diff --git a/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh b/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh index 3956d5d73f..69105b1668 100644 --- a/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh +++ b/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh @@ -1,20 +1,22 @@ -# # Copyright (C) 2011 OpenWrt.org -# PART_NAME=firmware -REQUIRE_IMAGE_METADATA=1 +REQUIRE_IMAGE_METADATA=1 platform_check_image() { return 0 } +RAMFS_COPY_BIN='fw_printenv fw_setenv' +RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock' + platform_do_upgrade() { local board=$(board_name) case "$board" in - glinet,gl-ar300m-nand) - default_do_upgrade "$1" + glinet,gl-ar300m-nand|\ + glinet,gl-ar300m-nor) + glinet_nand_nor_do_upgrade "$1" ;; *) nand_do_upgrade "$1"