From: Chukun Pan Date: Fri, 3 Nov 2023 15:02:35 +0000 (+0800) Subject: mediatek: filogic: add Netcore N60 support X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=5632227f440bf8a217556651324e47d55694ff4f;p=openwrt%2Fstaging%2Fjow.git mediatek: filogic: add Netcore N60 support Hardware specification: SoC: MediaTek MT7986A 4x A53 Flash: ESMT F50L1G41LB 128MB RAM: W632GU6NB DDR3 256MB Ethernet: 1x 2.5G + 4x 1G WiFi1: MT7975N 2.4GHz 4T4R WiFi2: MT7975PN 5GHz 4T4R Button: Reset, WPS Power: DC 12V 2A Flash instructions: 1. Connect to the router using ssh or telnet, username: useradmin, password is the web login password of the router. 2. Use scp to upload bl31-uboot.fip and flash: "mtd write xxx-preloader.bin spi0.0" "mtd write xxx-bl31-uboot.fip FIP" "mtd erase ubi" 3. Connect to the router via the Lan port, set a static ip of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 4. Download initramfs image, reboot router, waiting for tftp recovery to complete. 5. After openwrt boots up, perform sysupgrade. Note: 1. Back up all mtd partitions before flashing. Signed-off-by: Chukun Pan (cherry picked from commit 4ae474afbd023a3386f4276ca8f948a44b49ff1b) --- diff --git a/target/linux/mediatek/dts/mt7986a-netcore-n60.dts b/target/linux/mediatek/dts/mt7986a-netcore-n60.dts new file mode 100644 index 0000000000..b96b1e2ec0 --- /dev/null +++ b/target/linux/mediatek/dts/mt7986a-netcore-n60.dts @@ -0,0 +1,284 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; +#include +#include +#include + +#include "mt7986a.dtsi" + +/ { + model = "Netcore N60"; + compatible = "netcore,n60", "mediatek,mt7986a"; + + aliases { + serial0 = &uart0; + label-mac-device = &gmac0; + led-boot = &led_status_red; + led-failsafe = &led_status_red; + led-running = &led_status_blue; + led-upgrade = &led_status_blue; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0 0x40000000 0 0x10000000>; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + mesh { + label = "mesh"; + linux,code = ; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status_red: status-red { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&pio 29 GPIO_ACTIVE_LOW>; + }; + + led_status_blue: status-blue { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&pio 32 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cells = <&macaddr_lan>; + nvmem-cell-names = "mac-address"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-handle = <&phy6>; + phy-mode = "2500base-x"; + + nvmem-cells = <&macaddr_wan>; + nvmem-cell-names = "mac-address"; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + }; +}; + +&mdio { + reset-delay-us = <600>; + reset-post-delay-us = <20000>; + reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>; + + phy6: phy@6 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <6>; + mxl,led-config = <0x0 0x0 0x0 0x3f0>; + }; + + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <66 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + status = "okay"; + + flash@0 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + spi-max-frequency = <20000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x0000000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x0180000 0x0200000>; + read-only; + }; + + partition@380000 { + label = "FIP"; + reg = <0x0380000 0x0200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x0580000 0x7280000>; + }; + }; + }; +}; + +&pio { + spi_flash_pins: spi-flash-pins-33-to-38 { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + conf-pd { + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; + drive-strength = <8>; + mediatek,pull-down-adv = <0>; /* bias-disable */ + }; + }; + + wf_2g_5g_pins: wf_2g_5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; +}; + +&trng { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&wf_2g_5g_pins>; + + mediatek,mtd-eeprom = <&factory 0x0>; +}; + +&factory { + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_lan: macaddr@1fef20 { + reg = <0x1fef20 0x6>; + }; + + macaddr_wan: macaddr@1fef26 { + reg = <0x1fef26 0x6>; + }; + }; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 7d2cd706a9..b4d8d0e9aa 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -26,6 +26,7 @@ mediatek_setup_interfaces() asus,tuf-ax4200|\ jdcloud,re-cp-03|\ mediatek,mt7981-rfb|\ + netcore,n60|\ unielec,u7981-01*|\ zbtlink,zbt-z8102ax) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" eth1 diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 7cecd82f9f..62bbde6ba8 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -85,7 +85,8 @@ case "$board" in [ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress ;; - jcg,q30-pro) + jcg,q30-pro|\ + netcore,n60) # Originally, phy1 is phy0 mac with LA bit set. However, this would conflict # addresses on multiple VIFs with the other radio. Use label mac to set LA bit. [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(get_mac_label) > /sys${DEVPATH}/macaddress diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index fb981376fc..c26b672b1e 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -124,6 +124,7 @@ platform_do_upgrade() { h3c,magic-nx30-pro|\ jcg,q30-pro|\ mediatek,mt7981-rfb|\ + netcore,n60|\ qihoo,360t7|\ tplink,tl-xdr4288|\ tplink,tl-xdr6086|\ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index c94aac9681..83da1bb789 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -692,6 +692,30 @@ define Device/mercusys_mr90x-v1 endef TARGET_DEVICES += mercusys_mr90x-v1 +define Device/netcore_n60 + DEVICE_VENDOR := Netcore + DEVICE_MODEL := N60 + DEVICE_DTS := mt7986a-netcore-n60 + DEVICE_DTS_DIR := ../dts + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_IN_UBI := 1 + UBOOTENV_IN_UBI := 1 + IMAGES := sysupgrade.itb + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + KERNEL := kernel-bin | gzip + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGE/sysupgrade.itb := append-kernel | \ + fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata + DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware + ARTIFACTS := preloader.bin bl31-uboot.fip + ARTIFACT/preloader.bin := mt7986-bl2 spim-nand-ddr3 + ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot netcore_n60 +endef +TARGET_DEVICES += netcore_n60 + define Device/netgear_wax220 DEVICE_VENDOR := NETGEAR DEVICE_MODEL := WAX220