From: Ansuel Smith Date: Sun, 15 Dec 2019 01:25:04 +0000 (+0100) Subject: ipq806x: fix bug in L2 cache scaling X-Git-Tag: v21.02.0-rc1~4248 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=5ab9c0b388e9cf2537ef23d6e9baaf5730a14a1c;p=openwrt%2Fstaging%2Fchunkeey.git ipq806x: fix bug in L2 cache scaling It has been notice a buf in L2 cache scaling where the scaling is not done proprely if the frequency is set to the initial state before the new frequency. From: https://patchwork.kernel.org/patch/10565443/ * The clocks are set to aux clock rate first to make sure the * secondary mux is not sourcing off of QSB. The rate is then set to * two different rates to force a HFPLL reinit under all * circumstances. In the initial stage of boot to force a new frequency to apply, is needed to first set the frequency back to the lowest one (aux_rate) and then to the target one. This force and make sure the controller actually switch the frequency to the right one. Apply the same mechanism to L2 frequency scaling. Before scaling to the target frequency, first set the frequency to the aux_rate to force the transition, then scale it to the target frequency. Doing the wrong way can produce unexpected results and could lock the scaling mechanism until a full reboot is done (Causing a full reset by the krait-cc driver) From: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=77612720a2362230af726baa4149c40ec7a7fb05 When the Hfplls are reprogrammed during the rate change, the primary muxes which are sourced from the same hfpll for higher frequencies, needs to be switched to the 'safe secondary mux' as the parent for that small window. This is done by registering a clk notifier for the muxes and switching to the safe parent in the PRE_RATE_CHANGE notifier and back to the original parent in the POST_RATE_CHANGE notifier. This should apply also to L2 scaling... as we can't relly use the notifier, we manually do this on L2 scaling. Tested-by: Stefan Lippers-Hollmann [nbg6817/ipq8065] Signed-off-by: Ansuel Smith --- diff --git a/target/linux/ipq806x/patches-4.19/0055-cpufreq-dt-Add-L2-frequency-scaling-support.patch b/target/linux/ipq806x/patches-4.19/0055-cpufreq-dt-Add-L2-frequency-scaling-support.patch index bf4935a7c9..fa9aa3fff0 100644 --- a/target/linux/ipq806x/patches-4.19/0055-cpufreq-dt-Add-L2-frequency-scaling-support.patch +++ b/target/linux/ipq806x/patches-4.19/0055-cpufreq-dt-Add-L2-frequency-scaling-support.patch @@ -11,7 +11,7 @@ Signed-off-by: Georgi Djakov --- a/drivers/cpufreq/cpufreq-dt.c +++ b/drivers/cpufreq/cpufreq-dt.c -@@ -49,11 +49,39 @@ static int set_target(struct cpufreq_pol +@@ -49,11 +49,40 @@ static int set_target(struct cpufreq_pol struct private_data *priv = policy->driver_data; unsigned long freq = policy->freq_table[index].frequency; int ret; @@ -43,6 +43,7 @@ Signed-off-by: Georgi Djakov + l2_freq = clk_get_rate(l2_clk); + + if (l2_freq != new_l2_freq) { ++ ret = clk_set_rate(l2_clk, policy->l2_rate[0]); + /* scale l2 with the core */ + ret = clk_set_rate(l2_clk, new_l2_freq); + }