From: Ansuel Smith Date: Sun, 19 Dec 2021 00:16:11 +0000 (+0100) Subject: kernel: 5.10: backport additional qca8k fixes X-Git-Tag: v22.03.0-rc1~838 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=5cf198f7643975a12d7c4f95674349988d76b711;p=openwrt%2Fstaging%2Fhauke.git kernel: 5.10: backport additional qca8k fixes Backport 3 additional fixes for qca8k. - Fix MTU calculation - Fix a bug with config set to the wrong PAD when secondary cpu port is defined. - Fix redundant check in parse_port_config Signed-off-by: Ansuel Smith --- diff --git a/target/linux/generic/backport-5.10/751-v5.16-net-dsa-qca8k-fix-internal-delay-applied-to-the-wrong-PAD.patch b/target/linux/generic/backport-5.10/751-v5.16-net-dsa-qca8k-fix-internal-delay-applied-to-the-wrong-PAD.patch new file mode 100644 index 0000000000..df9518d86c --- /dev/null +++ b/target/linux/generic/backport-5.10/751-v5.16-net-dsa-qca8k-fix-internal-delay-applied-to-the-wrong-PAD.patch @@ -0,0 +1,48 @@ +From 3b00a07c2443745d62babfe08dbb2ad8e649526e Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 19 Nov 2021 03:03:49 +0100 +Subject: [PATCH] net: dsa: qca8k: fix internal delay applied to the wrong PAD + config + +With SGMII phy the internal delay is always applied to the PAD0 config. +This is caused by the falling edge configuration that hardcode the reg +to PAD0 (as the falling edge bits are present only in PAD0 reg) +Move the delay configuration before the reg overwrite to correctly apply +the delay. + +Fixes: cef08115846e ("net: dsa: qca8k: set internal delay also for sgmii") +Signed-off-by: Ansuel Smith +Reviewed-by: Vladimir Oltean +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 12 ++++++------ + 1 file changed, 6 insertions(+), 6 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1433,6 +1433,12 @@ qca8k_phylink_mac_config(struct dsa_swit + + qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val); + ++ /* From original code is reported port instability as SGMII also ++ * require delay set. Apply advised values here or take them from DT. ++ */ ++ if (state->interface == PHY_INTERFACE_MODE_SGMII) ++ qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg); ++ + /* For qca8327/qca8328/qca8334/qca8338 sgmii is unique and + * falling edge is set writing in the PORT0 PAD reg + */ +@@ -1455,12 +1461,6 @@ qca8k_phylink_mac_config(struct dsa_swit + QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE, + val); + +- /* From original code is reported port instability as SGMII also +- * require delay set. Apply advised values here or take them from DT. +- */ +- if (state->interface == PHY_INTERFACE_MODE_SGMII) +- qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg); +- + break; + default: + dev_err(ds->dev, "xMII mode %s not supported for port %d\n", diff --git a/target/linux/generic/backport-5.10/752-v5.16-net-dsa-qca8k-fix-MTU-calculation.patch b/target/linux/generic/backport-5.10/752-v5.16-net-dsa-qca8k-fix-MTU-calculation.patch new file mode 100644 index 0000000000..7348d93ec4 --- /dev/null +++ b/target/linux/generic/backport-5.10/752-v5.16-net-dsa-qca8k-fix-MTU-calculation.patch @@ -0,0 +1,46 @@ +From 65258b9d8cde45689bdc86ca39b50f01f983733b Mon Sep 17 00:00:00 2001 +From: Robert Marko +Date: Fri, 19 Nov 2021 03:03:50 +0100 +Subject: [PATCH] net: dsa: qca8k: fix MTU calculation + +qca8k has a global MTU, so its tracking the MTU per port to make sure +that the largest MTU gets applied. +Since it uses the frame size instead of MTU the driver MTU change function +will then add the size of Ethernet header and checksum on top of MTU. + +The driver currently populates the per port MTU size as Ethernet frame +length + checksum which equals 1518. + +The issue is that then MTU change function will go through all of the +ports, find the largest MTU and apply the Ethernet header + checksum on +top of it again, so for a desired MTU of 1500 you will end up with 1536. + +This is obviously incorrect, so to correct it populate the per port struct +MTU with just the MTU and not include the Ethernet header + checksum size +as those will be added by the MTU change function. + +Fixes: f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks") +Signed-off-by: Robert Marko +Signed-off-by: Ansuel Smith +Reviewed-by: Vladimir Oltean +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 6 +++++- + 1 file changed, 5 insertions(+), 1 deletion(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1256,8 +1256,12 @@ qca8k_setup(struct dsa_switch *ds) + /* Set initial MTU for every port. + * We have only have a general MTU setting. So track + * every port and set the max across all port. ++ * Set per port MTU to 1500 as the MTU change function ++ * will add the overhead and if its set to 1518 then it ++ * will apply the overhead again and we will end up with ++ * MTU of 1536 instead of 1518 + */ +- priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; ++ priv->port_mtu[i] = ETH_DATA_LEN; + } + + /* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */ diff --git a/target/linux/generic/backport-5.10/753-net-next-net-dsa-qca8k-remove-redundant-check-in-parse_port_config.patch b/target/linux/generic/backport-5.10/753-net-next-net-dsa-qca8k-remove-redundant-check-in-parse_port_config.patch new file mode 100644 index 0000000000..f477b1b929 --- /dev/null +++ b/target/linux/generic/backport-5.10/753-net-next-net-dsa-qca8k-remove-redundant-check-in-parse_port_config.patch @@ -0,0 +1,29 @@ +From b9133f3ef5a2659730cf47a74bd0a9259f1cf8ff Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Mon, 22 Nov 2021 16:23:40 +0100 +Subject: net: dsa: qca8k: remove redundant check in parse_port_config + +The very next check for port 0 and 6 already makes sure we don't go out +of bounds with the ports_config delay table. +Remove the redundant check. + +Reported-by: kernel test robot +Reported-by: Dan Carpenter +Signed-off-by: Ansuel Smith +Reviewed-by: Vladimir Oltean +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -983,7 +983,7 @@ qca8k_parse_port_config(struct qca8k_pri + u32 delay; + + /* We have 2 CPU port. Check them */ +- for (port = 0; port < QCA8K_NUM_PORTS && cpu_port_index < QCA8K_NUM_CPU_PORTS; port++) { ++ for (port = 0; port < QCA8K_NUM_PORTS; port++) { + /* Skip every other port */ + if (port != 0 && port != 6) + continue;