From: John Crispin Date: Tue, 7 Jul 2015 13:44:53 +0000 (+0000) Subject: lantiq: Add support for the BT Home Hub 5A X-Git-Tag: reboot~2591 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=6bdd209f152d2c98fefabcc486dc063420cda6a9;p=openwrt%2Fstaging%2Fxback.git lantiq: Add support for the BT Home Hub 5A u-boot support depends on the next "upstream" version ([0]) from Daniel Schwierzeck. Since the installation process is quite complicated a "how to" was added to the wiki: [1] [0] https://github.com/danielschwierzeck/u-boot-lantiq/tree/openwrt/v2014.01-next [1] http://wiki.openwrt.org/toh/bt/homehub_v5a V2: Use the correct PCI interrupt (fixes 2.4GHz wifi) Signed-off-by: Martin Blumenstingl SVN-Revision: 46223 --- diff --git a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/11-ath10k-caldata new file mode 100644 index 0000000000..0d8084fa10 --- /dev/null +++ b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -0,0 +1,51 @@ +#!/bin/sh +# Based on ar71xx 11-ath10k-caldata and 10-rt2x00-eeprom + +ath10k_caldata_die() { + echo "ath10k caldata: " "$*" + exit 1 +} + +ath10k_caldata_extract() { + local part=$1 + local offset=$2 + local mtd + + . /lib/functions.sh + + mtd=$(find_mtd_part $part) + [ -n "$mtd" ] || \ + ath10k_caldata_die "no mtd device found for partition $part" + + dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=2116 || \ + ath10k_caldata_die "failed to extract from $mtd" +} + +ath10k_caldata_set_macaddr() { + local macaddr=$1 + + macaddr_2bin $macaddr | dd of=/lib/firmware/$FIRMWARE \ + conv=notrunc bs=1 seek=6 count=6 +} + +[ -e /lib/firmware/$FIRMWARE ] && exit 0 +. /lib/functions.sh +. /lib/functions/system.sh +. /lib/functions/lantiq.sh + +case "$FIRMWARE" in +"ath10k/cal-pci-0000:02:00.0.bin") + local board=$(lantiq_board_name) + case $board in + BTHOMEHUBV5A) + local lan_mac=$(mtd_get_mac_binary caldata 4364) + local wifi_mac=$(macaddr_add "$lan_mac" 3) + ath10k_caldata_extract "caldata" 20480 + ath10k_caldata_set_macaddr $wifi_mac + ;; + *) + ath10k_caldata_die "board $board is not supported yet" + ;; + esac + ;; +esac diff --git a/target/linux/lantiq/base-files/etc/uci-defaults/01_leds b/target/linux/lantiq/base-files/etc/uci-defaults/01_leds index 8041ac941f..3e05ebaa87 100644 --- a/target/linux/lantiq/base-files/etc/uci-defaults/01_leds +++ b/target/linux/lantiq/base-files/etc/uci-defaults/01_leds @@ -25,7 +25,7 @@ BTHOMEHUBV2B) ucidef_set_led_netdev "internet" "internet" "soc:blue:broadband" "pppoa-wan" ucidef_set_led_usbdev "usb" "usb" "soc:blue:phone" "1-1" ;; -BTHOMEHUBV3A) +BTHOMEHUBV3A|BTHOMEHUBV5A) ucidef_set_led_default "power" "power" "soc:blue:power" "1" ucidef_set_led_wlan "wifi" "wifi" "soc:blue:wireless" "phy0tpt" ucidef_set_led_netdev "internet" "internet" "soc:blue:broadband" "pppoa-wan" diff --git a/target/linux/lantiq/base-files/etc/uci-defaults/02_network b/target/linux/lantiq/base-files/etc/uci-defaults/02_network index afb8714fe8..6f9d9c022d 100644 --- a/target/linux/lantiq/base-files/etc/uci-defaults/02_network +++ b/target/linux/lantiq/base-files/etc/uci-defaults/02_network @@ -169,6 +169,14 @@ BTHOMEHUBV2B|BTHOMEHUBV3A) wan_mac=$(macaddr_add "$lan_mac" 1) ;; +BTHOMEHUBV5A) + lan_mac=$(mtd_get_mac_binary caldata 4364) + wan_mac=$(macaddr_add "$lan_mac" 1) + ucidef_set_interface_lan 'eth0.1' + ucidef_add_switch "switch0" "1" "1" + ucidef_add_switch_vlan "switch0" "1" "0 1 2 4 6t" + ;; + VGV7519) lan_mac=$(mtd_get_mac_binary board_config 22) wan_mac=$(macaddr_add "$lan_mac" 1) diff --git a/target/linux/lantiq/base-files/lib/upgrade/platform.sh b/target/linux/lantiq/base-files/lib/upgrade/platform.sh index 1688d3af2e..f255e81799 100755 --- a/target/linux/lantiq/base-files/lib/upgrade/platform.sh +++ b/target/linux/lantiq/base-files/lib/upgrade/platform.sh @@ -7,7 +7,7 @@ platform_check_image() { local board=$(lantiq_board_name) case "$board" in - BTHOMEHUBV2B|BTHOMEHUBV3A|P2812HNUF* ) + BTHOMEHUBV2B|BTHOMEHUBV3A|BTHOMEHUBV5A|P2812HNUF* ) nand_do_platform_check $board $1 return $?; ;; diff --git a/target/linux/lantiq/dts/BTHOMEHUBV5A.dts b/target/linux/lantiq/dts/BTHOMEHUBV5A.dts new file mode 100644 index 0000000000..e8cdbbfe39 --- /dev/null +++ b/target/linux/lantiq/dts/BTHOMEHUBV5A.dts @@ -0,0 +1,287 @@ +/dts-v1/; + +/include/ "vr9.dtsi" + +/ { + model = "BTHOMEHUBV5A - BT Home Hub 5A"; + + chosen { + bootargs = "console=ttyLTQ0,115200 init=/etc/preinit"; + }; + + memory@0 { + reg = <0x0 0x8000000>; + }; + + fpi@10000000 { + localbus@0 { + nand-parts@0 { + compatible = "gen_nand", "lantiq,nand-xway"; + lantiq,cs = <1>; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x40000>; + read-only; + }; + partition@40000 { + label = "uboot-env"; + reg = <0x40000 0x40000>; + }; + caldata: partition@80000 { + label = "caldata"; + reg = <0x80000 0x20000>; + read-only; + }; + partition@a0000 { + label = "kernel"; + reg = <0xa0000 0x200000>; + }; + partition@2a0000 { + label = "ubi"; + reg = <0x2a0000 0x7d60000>; + }; + }; + }; + + gpio: pinmux@E100B10 { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + interrupt-parent = <&icu0>; + interrupts = <166 135 66 40 41 42 38>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,output = <1>; + lantiq,open-drain; + }; + pcie_rst { + lantiq,pins = "io38"; + lantiq,pull = <0>; + lantiq,output = <1>; + lantiq,open-drain; + }; + usb_vbus { + lantiq,pins = "io33"; + lantiq,pull = <0>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + nand_out { + lantiq,groups = "nand cle", "nand ale"; + lantiq,function = "ebu"; + lantiq,output = <1>; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + nand_cs1 { + lantiq,groups = "nand cs1"; + lantiq,function = "ebu"; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + }; + }; + + eth@E108000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-net"; + reg = < 0xE108000 0x3000 /* switch */ + 0xE10B100 0x70 /* mdio */ + 0xE10B1D8 0x30 /* mii */ + 0xE10B308 0x30 >; /* pmac */ + interrupt-parent = <&icu0>; + interrupts = <73 72>; + + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + mtd-mac-address = <&caldata 0x110c>; + lantiq,switch; + + ethernet@0 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <0>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + ethernet@1 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <1>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "gmii"; + phy-handle = <&phy11>; + }; + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "gmii"; + phy-handle = <&phy13>; + }; + }; + + wan: interface@1 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + mtd-mac-address = <&caldata 0x110c>; + mtd-mac-address-increment = <4>; + lantiq,wan; + + ethernet@5 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <5>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + + phy0: ethernet-phy@0 { + reg = <0x0>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy1: ethernet-phy@1 { + reg = <0x1>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + }; + }; + + ifxhcd@E101000 { + status = "okay"; + gpios = <&gpio 33 0>; + }; + + pci@E105400 { + status = "okay"; + lantiq,bus-clock = <33333333>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = <0x7000 0 0 1 &icu0 30 1>; + gpio-reset = <&gpio 21 0>; + }; + }; + + gphy-xrx200 { + compatible = "lantiq,phy-xrx200"; + firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/ + firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/ + phys = [ 00 01 ]; + }; + + ath9k_eep { + compatible = "ath9k,eeprom"; + ath,eep-flash = <&caldata 0x1000>; + ath,mac-offset = <0x110c>; + ath,mac-increment = <2>; + ath,pci-slot = <0xe>; /* 14 */ + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 2 1>; + linux,code = <0x198>; + }; + + wps { + label = "wps"; + gpios = <&gpio 25 1>; + linux,code = <0x211>; + }; + + restart { + label = "restart"; + gpios = <&gpio 39 1>; + linux,code = <0x198>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + broadband-red { + label = "soc:red:broadband"; + gpios = <&gpio 0 1>; + }; + broadband-green { + label = "soc:green:broadband"; + gpios = <&gpio 3 1>; + }; + broadband-blue { + label = "soc:blue:broadband"; + gpios = <&gpio 8 1>; + }; + + wireless-red { + label = "soc:red:wireless"; + gpios = <&gpio 9 1>; + }; + wireless-green { + label = "soc:green:wireless"; + gpios = <&gpio 10 1>; + }; + wireless-blue { + label = "soc:blue:wireless"; + gpios = <&gpio 11 1>; + }; + + power-red { + label = "soc:red:power"; + gpios = <&gpio 12 1>; + }; + power-green { + label = "soc:green:power"; + gpios = <&gpio 14 1>; + }; + power-blue { + label = "soc:blue:power"; + gpios = <&gpio 15 1>; + }; + + dimmed { + label = "dimmed"; + gpios = <&gpio 19 0>; + }; + }; +}; diff --git a/target/linux/lantiq/image/Makefile b/target/linux/lantiq/image/Makefile index 3e8c20b55c..726092db8f 100644 --- a/target/linux/lantiq/image/Makefile +++ b/target/linux/lantiq/image/Makefile @@ -414,6 +414,9 @@ Image/Build/Profile/P2812HNUF3=$(call Image/BuildNAND/$(1),$(1),P2812HNUF3) Image/BuildKernel/Profile/ARV7519RW22=$(call Image/BuildKernel/Template,ARV7519RW22,$(1)) Image/Build/Profile/ARV7519RW22=$(call Image/Build/$(1),$(1),ARV7519RW22) +Image/BuildKernel/Profile/BTHOMEHUBV5A=$(call Image/BuildKernel/Template,BTHOMEHUBV5A) +Image/Build/Profile/BTHOMEHUBV5A=$(call Image/BuildNAND/$(1),$(1),BTHOMEHUBV5A) + Image/BuildKernel/Profile/EASY80920NAND=$(call Image/BuildKernel/Template,EASY80920NAND) Image/Build/Profile/EASY80920NAND=$(call Image/Build/$(1),$(1),EASY80920NAND) diff --git a/target/linux/lantiq/xrx200/profiles/bt.mk b/target/linux/lantiq/xrx200/profiles/bt.mk new file mode 100644 index 0000000000..a1083bbb6d --- /dev/null +++ b/target/linux/lantiq/xrx200/profiles/bt.mk @@ -0,0 +1,9 @@ +define Profile/BTHOMEHUBV5A + NAME:=BT Home Hub 5A + PACKAGES:=kmod-ath9k kmod-ath10k wpad-mini kmod-usb-dwc2 +endef + +BTHOMEHUBV5A_UBIFS_OPTS:="-m 2048 -e 126KiB -c 4096" +BTHOMEHUBV5A_UBI_OPTS:="-m 2048 -p 128KiB -s 512" + +$(eval $(call Profile,BTHOMEHUBV5A))