From: Daniel González Cabanelas Date: Sun, 18 Jun 2023 19:34:59 +0000 (+0200) Subject: bmips: add support for NuCom R5010UNv2 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=6cb3328b4fd4939f3800d4be9d52744b753de1b6;p=openwrt%2Fstaging%2Flinusw.git bmips: add support for NuCom R5010UNv2 The NuCom R5010UNv2 is a wifi fast ethernet router, 2.4 GHz single band with two external antennas. Hardware: - SoC: Broadcom BCM6328 - CPU: single core BMIPS4350 V7.5 @ 320Mhz - RAM: 64 MB DDR2 - Flash: 16 MB SPI NOR - Ethernet LAN: 4x 100Mbit - Wifi 2.4 GHz: Broadcom BCM43217 802.11bgn (onboard) - USB: 1x 2.0 - Buttons: 2x - ADSL: yes, unsupported - LEDs: 7x - UART: yes Installation via CFE web UI: 1. Power off the router and press the RESET button 2. Power on the router and wait 12 or more seconds 3. Release the RESET button 4. Browse to http://192.168.1.1 and upload the Openwrt cfe firmware 5. Wait a few minutes for it to finish Signed-off-by: Daniel González Cabanelas --- diff --git a/target/linux/bmips/bcm6328/base-files/etc/board.d/01_leds b/target/linux/bmips/bcm6328/base-files/etc/board.d/01_leds index 5ece1f7ba1..5e80eb34e7 100644 --- a/target/linux/bmips/bcm6328/base-files/etc/board.d/01_leds +++ b/target/linux/bmips/bcm6328/base-files/etc/board.d/01_leds @@ -6,6 +6,7 @@ board_config_update case "$(board_name)" in +nucom,r5010unv2 |\ sercomm,ad1018) ucidef_set_led_usbport "usb" "USB" "green:usb" "usb1-port1" "usb2-port1" ;; diff --git a/target/linux/bmips/bcm6328/base-files/etc/board.d/02_network b/target/linux/bmips/bcm6328/base-files/etc/board.d/02_network index 66f9282e48..bfedad9e45 100644 --- a/target/linux/bmips/bcm6328/base-files/etc/board.d/02_network +++ b/target/linux/bmips/bcm6328/base-files/etc/board.d/02_network @@ -6,7 +6,8 @@ board_config_update case "$(board_name)" in comtrend,ar-5381u |\ -comtrend,ar-5387un) +comtrend,ar-5387un |\ +nucom,r5010unv2) ucidef_set_bridge_device switch ucidef_set_interface_lan "lan1 lan2 lan3 lan4" ;; diff --git a/target/linux/bmips/bcm6328/base-files/etc/uci-defaults/09_fix_crc b/target/linux/bmips/bcm6328/base-files/etc/uci-defaults/09_fix_crc index 21f18b4b81..2056ea017f 100644 --- a/target/linux/bmips/bcm6328/base-files/etc/uci-defaults/09_fix_crc +++ b/target/linux/bmips/bcm6328/base-files/etc/uci-defaults/09_fix_crc @@ -4,7 +4,8 @@ case "$(board_name)" in comtrend,ar-5381u |\ -comtrend,ar-5387un) +comtrend,ar-5387un |\ +nucom,r5010unv2) mtd fixtrx firmware ;; esac diff --git a/target/linux/bmips/dts/bcm6328-nucom-r5010unv2.dts b/target/linux/bmips/dts/bcm6328-nucom-r5010unv2.dts new file mode 100644 index 0000000000..826b2a61e2 --- /dev/null +++ b/target/linux/bmips/dts/bcm6328-nucom-r5010unv2.dts @@ -0,0 +1,216 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "bcm6328.dtsi" + +/ { + model = "NuCom R5010UNv2"; + compatible = "nucom,r5010unv2", "brcm,bcm6328"; + + aliases { + led-boot = &led_power_green; + led-failsafe = &led_power_red; + led-running = &led_power_green; + led-upgrade = &led_power_green; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + wps { + label = "wps"; + gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; + + bcm43217-sprom { + compatible = "brcm,bcma-sprom"; + + pci-bus = <1>; + pci-dev = <0>; + + nvmem-cells = <&macaddr_cfe_6a0>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <1>; + + brcm,sprom = "brcm/bcm43217-sprom.bin"; + }; +}; + +&ehci { + status = "okay"; +}; + +ðernet { + status = "okay"; + + nvmem-cells = <&macaddr_cfe_6a0>; + nvmem-cell-names = "mac-address"; +}; + +&hsspi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <16666667>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + cfe: partition@0 { + label = "cfe"; + reg = <0x000000 0x010000>; + read-only; + }; + + partition@10000 { + compatible = "brcm,bcm963xx-imagetag"; + label = "firmware"; + reg = <0x010000 0xfe0000>; + }; + + partition@ff0000 { + label = "nvram"; + reg = <0xff0000 0x010000>; + }; + }; + }; +}; + +&leds { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ephy0_act_led &pinctrl_ephy1_act_led + &pinctrl_ephy2_act_led &pinctrl_ephy3_act_led + &pinctrl_leds>; + + led@1 { + reg = <1>; + active-low; + label = "green:internet"; + }; + + led@2 { + reg = <2>; + active-low; + label = "red:internet"; + }; + + led@3 { + reg = <3>; + active-low; + label = "green:dsl"; + }; + + led_power_green: led@4 { + reg = <4>; + active-low; + label = "green:power"; + }; + + led_power_red: led@5 { + reg = <5>; + active-low; + label = "red:power"; + panic-indicator; + }; + + led@10 { + reg = <10>; + active-low; + label = "green:wps"; + }; + + led@11 { + reg = <11>; + active-low; + label = "green:usb"; + }; +}; + +&ohci { + status = "okay"; +}; + +&pcie { + status = "okay"; +}; + +&pinctrl { + pinctrl_leds: leds { + function = "led"; + pins = "gpio1", "gpio2", "gpio3", + "gpio4", "gpio5", "gpio10", + "gpio11"; + }; +}; + +&switch0 { + ports { + port@0 { + reg = <0>; + label = "lan1"; + + phy-handle = <&phy1>; + phy-mode = "mii"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + + phy-handle = <&phy2>; + phy-mode = "mii"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + + phy-handle = <&phy3>; + phy-mode = "mii"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + + phy-handle = <&phy4>; + phy-mode = "mii"; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&usbh { + status = "okay"; +}; + +&cfe { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_cfe_6a0: macaddr@6a0 { + reg = <0x6a0 0x6>; + }; +}; diff --git a/target/linux/bmips/image/bcm6328.mk b/target/linux/bmips/image/bcm6328.mk index ef74410f1e..8023ef8fa1 100644 --- a/target/linux/bmips/image/bcm6328.mk +++ b/target/linux/bmips/image/bcm6328.mk @@ -26,6 +26,19 @@ define Device/comtrend_ar-5387un endef TARGET_DEVICES += comtrend_ar-5387un +define Device/nucom_r5010unv2 + $(Device/bcm63xx-cfe) + DEVICE_VENDOR := NuCom + DEVICE_MODEL := R5010UNv2 + CHIP_ID := 6328 + CFE_BOARD_ID := 96328ang + FLASH_MB := 16 + DEVICE_PACKAGES += $(USB2_PACKAGES) \ + $(B43_PACKAGES) broadcom-43217-sprom \ + kmod-leds-bcm6328 +endef +TARGET_DEVICES += nucom_r5010unv2 + define Device/sercomm_ad1018 $(Device/sercomm-nand) DEVICE_VENDOR := Sercomm