From: Daniel González Cabanelas Date: Sat, 10 Jun 2023 19:05:33 +0000 (+0200) Subject: bmips: add support for Netgear EVG2000 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=71a6f45fdfe6221c755fa15379eab77110413f8e;p=openwrt%2Fstaging%2Fblocktrron.git bmips: add support for Netgear EVG2000 The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with two internal antennas integrated in the main PCB. Hardware: - SoC: Broadcom BCM6369 - CPU: dual core BMIPS4350 V3.1 @400Mhz - RAM: 64 MB DDR - Flash: 16 MB parallel NOR - LAN switch: Broadcom BCM53115, 5x 1Gbit - Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn - USB: 2x 2.0 - Buttons: 2x, 1 reset - LEDs: 10x - FXS: 2x - UART: yes Installation via CFE web UI: 1. Power off the router and make a temporal TX-RX shortcircuit on the serial pins. 2. Power on the router and wait 3 or more seconds 3. Remove the TX-RX shortcircuit 4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the firmware 5. Wait a few minutes for it to finish Signed-off-by: Daniel González Cabanelas --- diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds index e68a4e947b..fb7cca17e5 100644 --- a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds +++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds @@ -15,6 +15,11 @@ netgear,dgnd3800b) ucidef_set_led_usbport "usb1" "USB1" "green:usb1" "usb1-port1" "usb2-port1" ucidef_set_led_usbport "usb2" "USB2" "green:usb2" "usb1-port2" "usb2-port2" ;; +netgear,evg2000) + ucidef_set_led_netdev "lan" "LAN" "green:lan" "switch.1" + ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan" + ucidef_set_led_usbdev "usb" "USB" "green:usb" "usb1-port1" "usb2-port1" "usb1-port2" "usb2-port2" + ;; observa,vh4032n) ucidef_set_led_usbport "usb1" "USB1" "blue:hspa" "usb1-port1" "usb2-port1" ucidef_set_led_usbport "usb2" "USB2" "red:hspa" "1-2-port1" "1-2-port2" diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network index f99005acd7..76145024c1 100644 --- a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network +++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network @@ -11,7 +11,8 @@ observa,vh4032n) ucidef_set_interface_lan "lan1 lan2 lan3 lan4" ;; netgear,dgnd3700-v1 |\ -netgear,dgnd3800b) +netgear,dgnd3800b |\ +netgear,evg2000) ucidef_set_bridge_device switch ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan" ;; diff --git a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc index d4ff723d14..363e492594 100644 --- a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc +++ b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc @@ -4,6 +4,7 @@ case "$(board_name)" in comtrend,vr-3025u |\ +netgear,evg2000 |\ observa,vh4032n) mtd fixtrx firmware ;; diff --git a/target/linux/bmips/dts/bcm6369-netgear-evg2000.dts b/target/linux/bmips/dts/bcm6369-netgear-evg2000.dts new file mode 100644 index 0000000000..9f03c9e4dc --- /dev/null +++ b/target/linux/bmips/dts/bcm6369-netgear-evg2000.dts @@ -0,0 +1,237 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "bcm6368.dtsi" + +/ { + model = "Netgear EVG2000"; + compatible = "netgear,evg2000", "brcm,bcm6369", "brcm,bcm6368"; + + aliases { + led-boot = &led_power_green; + led-failsafe = &led_power_red; + led-running = &led_power_green; + led-upgrade = &led_power_green; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 25 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + wps { + label = "wps"; + gpios = <&gpio 26 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led@2 { + label = "green:voip2"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + }; + + led@4 { + label = "red:internet"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + led@5 { + label = "green:internet"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + + led@14 { + label = "green:voip1"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + led@15 { + label = "green:usb"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + led_power_green: led@22 { + label = "green:power"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + led_power_red: led@23 { + label = "red:power"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + }; + + led@24 { + label = "green:lan"; + gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + }; + + led@27 { + label = "green:wan"; + gpios = <&gpio 27 GPIO_ACTIVE_LOW>; + }; + }; + + bcm4322-sprom { + compatible = "brcm,ssb-sprom"; + + pci-bus = <0>; + pci-dev = <1>; + + nvmem-cells = <&macaddr_cfe_6a0>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <1>; + + brcm,sprom = "brcm/bcm4322-sprom.bin"; + brcm,sprom-fixups = <219 0xec08>; + }; +}; + +&ehci { + status = "okay"; +}; + +ðernet { + status = "okay"; + + nvmem-cells = <&macaddr_cfe_6a0>; + nvmem-cell-names = "mac-address"; +}; + +&mdio_ext { + switch@1e { + compatible = "brcm,bcm53115"; + reg = <30>; + + dsa,member = <1 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "wan"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + port@8 { + reg = <8>; + + phy-mode = "rgmii"; + ethernet = <&switch0port5>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +&switch0 { + dsa,member = <0 0>; + + ports { + switch0port5: port@5 { + reg = <5>; + label = "extsw"; + + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +}; + +&pflash { + status = "okay"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + cfe: partition@0 { + label = "CFE"; + reg = <0x000000 0x020000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x020000 0xf40000>; + compatible = "brcm,bcm963xx-imagetag"; + }; + + partition@f60000 { + label = "board_data"; + reg = <0xf60000 0x080000>; + read-only; + }; + + partition@fe0000 { + label = "nvram"; + reg = <0xfe0000 0x020000>; + }; + }; +}; + +&ohci { + status = "okay"; +}; + +&pci { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&usbh { + status = "okay"; +}; + +&cfe { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_cfe_6a0: macaddr@6a0 { + reg = <0x6a0 0x6>; + }; +}; diff --git a/target/linux/bmips/image/bcm6368.mk b/target/linux/bmips/image/bcm6368.mk index 41bce9e938..82d7608fba 100644 --- a/target/linux/bmips/image/bcm6368.mk +++ b/target/linux/bmips/image/bcm6368.mk @@ -43,6 +43,21 @@ define Device/netgear_dgnd3800b endef TARGET_DEVICES += netgear_dgnd3800b +define Device/netgear_evg2000 + $(Device/bcm63xx_netgear) + DEVICE_MODEL := EVG2000 + CFE_BOARD_ID := 96369PVG + CHIP_ID := 6368 + SOC := bcm6369 + BLOCKSIZE := 0x20000 + NETGEAR_BOARD_ID := U12H154T90_NETGEAR + NETGEAR_REGION := 1 + DEVICE_PACKAGES += $(USB2_PACKAGES) \ + $(B43_PACKAGES) broadcom-4322-sprom \ + kmod-leds-gpio +endef +TARGET_DEVICES += netgear_evg2000 + define Device/observa_vh4032n $(Device/bcm63xx-cfe) DEVICE_VENDOR := Observa