From: Mateus B. Cassiano Date: Wed, 15 Jul 2020 21:45:39 +0000 (-0400) Subject: ramips: add support for D-Link DIR-867/DIR-882 A1 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=73e8f23579bcb87764dae9ed0aefe28be3183d3e;p=openwrt%2Fstaging%2Faparcar.git ramips: add support for D-Link DIR-867/DIR-882 A1 This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given the similarity of these devices, this patch also introduces a common DTS shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green), USB 2.0 (green), USB 3.0 (green) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips * DIR-867 wireless chips are limited to 3x3 streams at hardware level * USB ports and related LEDs available only on DIR-882 Serial port: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Mateus B. Cassiano [move DEVICE_VARIANT to individual definitions] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ramips/dts/mt7621_dlink_dir-867-a1.dts b/target/linux/ramips/dts/mt7621_dlink_dir-867-a1.dts new file mode 100644 index 0000000000..34ddbeaec3 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_dlink_dir-867-a1.dts @@ -0,0 +1,40 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "mt7621_dlink_dir-8xx-a1.dtsi" + +/ { + compatible = "dlink,dir-867-a1", "mediatek,mt7621-soc"; + model = "D-Link DIR-867 A1"; + + aliases { + led-boot = &led_power_orange; + led-failsafe = &led_power_green; + led-running = &led_power_green; + led-upgrade = &led_net_orange; + }; + + leds { + compatible = "gpio-leds"; + + led_power_orange: power_orange { + label = "dir-867-a1:orange:power"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + led_power_green: power_green { + label = "dir-867-a1:green:power"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + led_net_orange: net_orange { + label = "dir-867-a1:orange:net"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + net_green { + label = "dir-867-a1:green:net"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + }; +}; diff --git a/target/linux/ramips/dts/mt7621_dlink_dir-878-a1.dts b/target/linux/ramips/dts/mt7621_dlink_dir-878-a1.dts index 15c46cb5f7..e2f569f40f 100644 --- a/target/linux/ramips/dts/mt7621_dlink_dir-878-a1.dts +++ b/target/linux/ramips/dts/mt7621_dlink_dir-878-a1.dts @@ -1,10 +1,7 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT /dts-v1/; -#include "mt7621.dtsi" - -#include -#include +#include "mt7621_dlink_dir-8xx-a1.dtsi" / { compatible = "dlink,dir-878-a1", "mediatek,mt7621-soc"; @@ -15,11 +12,6 @@ led-failsafe = &led_power_green; led-running = &led_power_green; led-upgrade = &led_net_orange; - label-mac-device = &gmac0; - }; - - chosen { - bootargs = "console=ttyS0,57600"; }; leds { @@ -45,137 +37,4 @@ gpios = <&gpio 3 GPIO_ACTIVE_LOW>; }; }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - gpios = <&gpio 15 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&gpio 18 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wifi { - label = "wifi"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; -}; - -&spi0 { - status = "okay"; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <50000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x0 0x30000>; - read-only; - }; - - partition@30000 { - label = "u-boot-env"; - reg = <0x30000 0x10000>; - read-only; - }; - - factory: partition@40000 { - label = "factory"; - reg = <0x40000 0x20000>; - read-only; - }; - - partition@60000 { - compatible = "sge,uimage"; - label = "firmware"; - reg = <0x60000 0xfa0000>; - }; - }; - }; -}; - -&pcie { - status = "okay"; -}; - -&pcie0 { - wifi@0,0 { - compatible = "mediatek,mt76"; - reg = <0x0000 0 0 0 0>; - mediatek,mtd-eeprom = <&factory 0x0000>; - ieee80211-freq-limit = <2400000 2500000>; - - led { - led-active-low; - }; - }; -}; - -&pcie1 { - wifi@0,0 { - compatible = "mediatek,mt76"; - reg = <0x0000 0 0 0 0>; - mediatek,mtd-eeprom = <&factory 0x8000>; - ieee80211-freq-limit = <5000000 6000000>; - - led { - led-active-low; - }; - }; -}; - -&gmac0 { - mtd-mac-address = <&factory 0xe000>; -}; - -&switch0 { - ports { - port@0 { - status = "okay"; - label = "lan4"; - }; - - port@1 { - status = "okay"; - label = "lan3"; - }; - - port@2 { - status = "okay"; - label = "lan2"; - }; - - port@3 { - status = "okay"; - label = "lan1"; - }; - - port@4 { - status = "okay"; - label = "wan"; - mtd-mac-address = <&factory 0xe006>; - }; - }; -}; - -&state_default { - gpio { - groups = "i2c", "uart3", "jtag", "wdt"; - function = "gpio"; - }; }; diff --git a/target/linux/ramips/dts/mt7621_dlink_dir-882-a1.dts b/target/linux/ramips/dts/mt7621_dlink_dir-882-a1.dts new file mode 100644 index 0000000000..11f70ecf3f --- /dev/null +++ b/target/linux/ramips/dts/mt7621_dlink_dir-882-a1.dts @@ -0,0 +1,54 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "mt7621_dlink_dir-8xx-a1.dtsi" + +/ { + compatible = "dlink,dir-882-a1", "mediatek,mt7621-soc"; + model = "D-Link DIR-882 A1"; + + aliases { + led-boot = &led_power_orange; + led-failsafe = &led_power_green; + led-running = &led_power_green; + led-upgrade = &led_net_orange; + }; + + leds { + compatible = "gpio-leds"; + + led_power_orange: power_orange { + label = "dir-882-a1:orange:power"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + led_power_green: power_green { + label = "dir-882-a1:green:power"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + led_net_orange: net_orange { + label = "dir-882-a1:orange:net"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + net_green { + label = "dir-882-a1:green:net"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + + usb2 { + label = "dir-882-a1:green:usb2"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + trigger-sources = <&ehci_port2>; + linux,default-trigger = "usbport"; + }; + + usb3 { + label = "dir-882-a1:green:usb3"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + trigger-sources = <&xhci_ehci_port1>; + linux,default-trigger = "usbport"; + }; + }; +}; diff --git a/target/linux/ramips/dts/mt7621_dlink_dir-8xx-a1.dtsi b/target/linux/ramips/dts/mt7621_dlink_dir-8xx-a1.dtsi new file mode 100644 index 0000000000..f2f0a4c56f --- /dev/null +++ b/target/linux/ramips/dts/mt7621_dlink_dir-8xx-a1.dtsi @@ -0,0 +1,149 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include + +/ { + aliases { + label-mac-device = &gmac0; + }; + + chosen { + bootargs = "console=ttyS0,57600"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wifi { + label = "wifi"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + compatible = "sge,uimage"; + label = "firmware"; + reg = <0x60000 0xfa0000>; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0000>; + ieee80211-freq-limit = <2400000 2500000>; + + led { + led-active-low; + }; + }; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + ieee80211-freq-limit = <5000000 6000000>; + + led { + led-active-low; + }; + }; +}; + +&gmac0 { + mtd-mac-address = <&factory 0xe000>; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan4"; + }; + + port@1 { + status = "okay"; + label = "lan3"; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@3 { + status = "okay"; + label = "lan1"; + }; + + port@4 { + status = "okay"; + label = "wan"; + mtd-mac-address = <&factory 0xe006>; + }; + }; +}; + +&state_default { + gpio { + groups = "i2c", "uart3", "jtag", "wdt"; + function = "gpio"; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index e97d2315f1..0315822c0b 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -220,6 +220,18 @@ define Device/buffalo_wsr-600dhp endef TARGET_DEVICES += buffalo_wsr-600dhp +define Device/dlink_dir-8xx-a1 + IMAGE_SIZE := 16000k + DEVICE_VENDOR := D-Link + DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware wpad-basic + KERNEL_INITRAMFS := $$(KERNEL) | uimage-padhdr 96 + IMAGES += factory.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\ + pad-rootfs | append-metadata | check-size + IMAGE/factory.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\ + check-size +endef + define Device/dlink_dir-860l-b1 $(Device/seama) BLOCKSIZE := 64k @@ -236,21 +248,28 @@ define Device/dlink_dir-860l-b1 endef TARGET_DEVICES += dlink_dir-860l-b1 +define Device/dlink_dir-867-a1 + $(Device/dlink_dir-8xx-a1) + DEVICE_MODEL := DIR-867 + DEVICE_VARIANT := A1 +endef +TARGET_DEVICES += dlink_dir-867-a1 + define Device/dlink_dir-878-a1 - IMAGE_SIZE := 16000k - DEVICE_VENDOR := D-Link + $(Device/dlink_dir-8xx-a1) DEVICE_MODEL := DIR-878 DEVICE_VARIANT := A1 - DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware wpad-basic - KERNEL_INITRAMFS := $$(KERNEL) | uimage-padhdr 96 - IMAGES += factory.bin - IMAGE/sysupgrade.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\ - pad-rootfs | append-metadata | check-size - IMAGE/factory.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\ - check-size endef TARGET_DEVICES += dlink_dir-878-a1 +define Device/dlink_dir-882-a1 + $(Device/dlink_dir-8xx-a1) + DEVICE_MODEL := DIR-882 + DEVICE_VARIANT := A1 + DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport +endef +TARGET_DEVICES += dlink_dir-882-a1 + define Device/d-team_newifi-d2 $(Device/uimage-lzma-loader) IMAGE_SIZE := 32448k diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds index a44b1a09d0..43cd77ccd1 100755 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds @@ -27,7 +27,9 @@ gehua,ghl-r-001) ucidef_set_led_netdev "internet" "internet" "$boardname:blue:internet" "wan" ;; dlink,dir-860l-b1|\ -dlink,dir-878-a1) +dlink,dir-867-a1|\ +dlink,dir-878-a1|\ +dlink,dir-882-a1) ucidef_set_led_netdev "wan" "wan" "$boardname:green:net" "wan" ;; gnubee,gb-pc1|\