From: Bartlomiej Zolnierkiewicz Date: Thu, 17 Apr 2008 22:46:24 +0000 (+0200) Subject: ide: remove CONFIG_BLK_DEV_HD_IDE config option (take 2) X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=80aa31cb460d12c1e02327b43eceb3eebc6e7090;p=openwrt%2Fstaging%2Fblogic.git ide: remove CONFIG_BLK_DEV_HD_IDE config option (take 2) * Remove CONFIG_BLK_DEV_HD hack from init_hwif_default() ("hda=noprobe hdb=noprobe" kernel parameters should be used instead if somebody wishes to use the old "hd" driver). * Make CONFIG_BLK_DEV_HD_ONLY config option available also when IDE subsystem is used and update help entry. * Remove no longer needed CONFIG_BLK_DEV_HD_IDE config option. v2: * Update documentation to suggest "hda=noprobe hdb=noprobe" instead of obsoleted "ide0=noprobe". * Update Documentation/ide/ide.txt. Signed-off-by: Bartlomiej Zolnierkiewicz --- diff --git a/Documentation/ide/ide.txt b/Documentation/ide/ide.txt index ce7c01af30f6..ae4f4f43c25c 100644 --- a/Documentation/ide/ide.txt +++ b/Documentation/ide/ide.txt @@ -184,13 +184,6 @@ provided it is mounted with the default block size of 1024 (as above). Please pass on any feedback on any of this stuff to the maintainer, whose address can be found in linux/MAINTAINERS. -Note that if BOTH hd.c and ide.c are configured into the kernel, -hd.c will normally be allowed to control the primary IDE interface. -This is useful for older hardware that may be incompatible with ide.c, -and still allows newer hardware to run on the 2nd/3rd/4th IDE ports -under control of ide.c. To have ide.c also "take over" the primary -IDE port in this situation, use the "command line" parameter: ide0=0x1f0 - The IDE driver is modularized. The high level disk/CD-ROM/tape/floppy drivers can always be compiled as loadable modules, the chipset drivers can only be compiled into the kernel, and the core code (ide.c) can be diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig index ac5875783430..4dc2761e9704 100644 --- a/drivers/ide/Kconfig +++ b/drivers/ide/Kconfig @@ -122,24 +122,6 @@ config BLK_DEV_IDE_SATA If unsure, say N. -config BLK_DEV_HD_IDE - bool "Use old disk-only driver on primary interface" - depends on (X86 || SH_MPC1211) - ---help--- - There are two drivers for MFM/RLL/IDE disks. Most people use just - the new enhanced driver by itself. This option however installs the - old hard disk driver to control the primary IDE/disk interface in - the system, leaving the new enhanced IDE driver to take care of only - the 2nd/3rd/4th IDE interfaces. Doing this will prevent you from - having an IDE/ATAPI CD-ROM or tape drive connected to the primary - IDE interface. Choosing this option may be useful for older systems - which have MFM/RLL/ESDI controller+drives at the primary port - address (0x1f0), along with IDE drives at the secondary/3rd/4th port - addresses. - - Normally, just say N here; you will then use the new driver for all - 4 interfaces. - config BLK_DEV_IDEDISK tristate "Include IDE/ATA-2 DISK support" ---help--- @@ -1114,7 +1096,6 @@ endif config BLK_DEV_HD_ONLY bool "Old hard disk (MFM/RLL/IDE) driver" - depends on BLK_DEV_IDE=n help There are two drivers for MFM/RLL/IDE hard disks. Most people use the newer enhanced driver, but this old one is still around for two @@ -1126,12 +1107,16 @@ config BLK_DEV_HD_ONLY for systems with only older MFM/RLL/ESDI drives. Choosing the old driver can save 13 KB or so of kernel memory. + If you want to use this driver together with the new one you have + to use "hda=noprobe hdb=noprobe" kernel parameters to prevent the new + driver from probing the primary interface. + If you are unsure, then just choose the Enhanced IDE/MFM/RLL driver instead of this one. For more detailed information, read the Disk-HOWTO, available from . config BLK_DEV_HD - def_bool BLK_DEV_HD_IDE || BLK_DEV_HD_ONLY + def_bool BLK_DEV_HD_ONLY endif # IDE diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c index d791b1ffb586..96126b3b12e9 100644 --- a/drivers/ide/ide.c +++ b/drivers/ide/ide.c @@ -177,10 +177,6 @@ static void init_hwif_default(ide_hwif_t *hwif, unsigned int index) memcpy(hwif->io_ports, hw.io_ports, sizeof(hw.io_ports)); hwif->noprobe = !hwif->io_ports[IDE_DATA_OFFSET]; -#ifdef CONFIG_BLK_DEV_HD - if (hwif->io_ports[IDE_DATA_OFFSET] == HD_DATA) - hwif->noprobe = 1; /* may be overridden by ide_setup() */ -#endif } /*