From: Christian Marangi Date: Thu, 16 Jun 2022 20:12:01 +0000 (+0200) Subject: ipq806x: 5.15: replace dtsi patches with upstream version X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=88bf6525251f7ef3d4f0b63e2cf77b42078101a4;p=openwrt%2Fstaging%2Fblocktrron.git ipq806x: 5.15: replace dtsi patches with upstream version Reorganize dtsi patches with upstream version and drop dtsi in 5.15 files. Also add an additional upstream patch for hwspinlock support. Refresh all the dts with needed changes. Signed-off-by: Christian Marangi --- diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8062-wg2600hp3.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8062-wg2600hp3.dts index c1c21856ca..11ae3f81c3 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8062-wg2600hp3.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8062-wg2600hp3.dts @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT -#include "qcom-ipq8062.dtsi" +#include "qcom-ipq8062-smb208.dtsi" #include /delete-node/ &nand_pins; @@ -134,6 +134,15 @@ }; }; +/* nand_pins are used for leds_pins, empty the node + * from ipq8064.dtsi + */ +&nand_pins { + /delete-property/ disable; + /delete-property/ pullups; + /delete-property/ hold; +}; + &qcom_pinmux { pinctrl-0 = <&akro_pins>; pinctrl-names = "default"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8062.dtsi b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8062.dtsi deleted file mode 100644 index 29226ca275..0000000000 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8062.dtsi +++ /dev/null @@ -1,98 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only - -#include "qcom-ipq8064.dtsi" - -/ { - model = "Qualcomm IPQ8062"; - compatible = "qcom,ipq8062", "qcom,ipq8064"; - - aliases { - serial0 = &gsbi4_serial; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; -}; - -&gsbi4 { - qcom,mode = ; - status = "okay"; - - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ -}; - -&opp_table0 { - /delete-node/opp-1200000000; - /delete-node/opp-1400000000; - - /* - * Voltage thresholds are - */ - opp-384000000 { - opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; - opp-microvolt-speed0-pvs1-v0 = < 925000 878750 971250>; - opp-microvolt-speed0-pvs2-v0 = < 875000 831250 918750>; - opp-microvolt-speed0-pvs3-v0 = < 800000 760000 840000>; - }; - - opp-600000000 { - opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; - opp-microvolt-speed0-pvs1-v0 = < 975000 926250 1023750>; - opp-microvolt-speed0-pvs2-v0 = < 925000 878750 971250>; - opp-microvolt-speed0-pvs3-v0 = < 850000 807500 892500>; - }; - - opp-800000000 { - opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; - opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; - opp-microvolt-speed0-pvs2-v0 = < 995000 945250 1044750>; - opp-microvolt-speed0-pvs3-v0 = < 900000 855000 945000>; - }; - - opp-1000000000 { - opp-microvolt-speed0-pvs0-v0 = <1150000 1092500 1207500>; - opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; - opp-microvolt-speed0-pvs2-v0 = <1025000 973750 1076250>; - opp-microvolt-speed0-pvs3-v0 = < 950000 902500 997500>; - }; -}; - -&pcie0 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&pcie1 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&pcie2 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&smb208_s2a { - regulator-max-microvolt = <1150000>; -}; - -&smb208_s2b { - regulator-max-microvolt = <1150000>; -}; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ad7200-c2600.dtsi b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ad7200-c2600.dtsi index 115c6d43d2..c6a78f7fd8 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ad7200-c2600.dtsi +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ad7200-c2600.dtsi @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT -#include "qcom-ipq8064-v2.0.dtsi" +#include "qcom-ipq8064-v2.0-smb208.dtsi" #include diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ap148.dts index 70034a50e3..cf73ed6a0a 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ap148.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ap148.dts @@ -54,9 +54,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - nand@0 { reg = <0>; compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ap161.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ap161.dts index c771a627ca..926d9286a7 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ap161.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-ap161.dts @@ -25,7 +25,7 @@ }; &qcom_pinmux { - rgmii2_pins: rgmii2_pins { + rgmii2_pins: rgmii2-pins { mux { pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", @@ -66,9 +66,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - nand@0 { reg = <0>; compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-d7800.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-d7800.dts index 23487c9ca0..f9f9c035d3 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-d7800.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-d7800.dts @@ -1,4 +1,4 @@ -#include "qcom-ipq8064-v2.0.dtsi" +#include "qcom-ipq8064-v2.0-smb208.dtsi" #include @@ -234,12 +234,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - #address-cells = <1>; - #size-cells = <0>; - nand@0 { reg = <0>; compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi index e74d2dcdbd..68e5b24704 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT -#include "qcom-ipq8064-v2.0.dtsi" +#include "qcom-ipq8064-v2.0-smb208.dtsi" #include @@ -37,9 +37,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - nand@0 { reg = <0>; compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-g10.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-g10.dts index 735ccb2d53..ba27d89c05 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-g10.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-g10.dts @@ -1,5 +1,5 @@ // SPDX-License-Identifier: GPL-2.0 -#include "qcom-ipq8064-v2.0.dtsi" +#include "qcom-ipq8064-v2.0-smb208.dtsi" #include #include @@ -158,26 +158,77 @@ pinctrl-0 = <&mdio0_pins>; pinctrl-names = "default"; - ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; + switch@10 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10>; + + qca8k,rgmii56_1_8v; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "wan"; + }; + + /* + port@6 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac2>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + asym-pause; + }; + }; + */ + }; }; }; &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - nand@0 { reg = <0>; compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-r7500.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-r7500.dts index 0970eaf0ec..1505e23f38 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-r7500.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-r7500.dts @@ -167,9 +167,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - nand@0 { reg = <0>; compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts index 30b56bb9d6..b43ee90034 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts @@ -1,4 +1,4 @@ -#include "qcom-ipq8064-v2.0.dtsi" +#include "qcom-ipq8064-v2.0-smb208.dtsi" #include @@ -231,9 +231,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - nand@0 { reg = <0>; compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-unifi-ac-hd.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-unifi-ac-hd.dts index b3e06db86d..90927ddb85 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-unifi-ac-hd.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-unifi-ac-hd.dts @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT -#include "qcom-ipq8064-v2.0.dtsi" +#include "qcom-ipq8064-v2.0-smb208.dtsi" #include #include @@ -221,8 +221,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; nand-ecc-strength = <4>; nand-bus-width = <8>; }; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi deleted file mode 100644 index b9ee86a891..0000000000 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi +++ /dev/null @@ -1,69 +0,0 @@ -#include "qcom-ipq8064.dtsi" - -/ { - aliases { - serial0 = &gsbi4_serial; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; -}; - -&gsbi4 { - qcom,mode = ; - status = "okay"; - - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ -}; - -&CPU_SPC { - status = "okay"; -}; - -&pcie0 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&pcie1 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&pcie2 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&sata { - ports-implemented = <0x1>; -}; - -&ss_phy_0 { - qcom,rx-eq = <2>; - qcom,tx-deamp_3_5db = <32>; - qcom,mpll = <5>; -}; - -&ss_phy_1 { - qcom,rx-eq = <2>; - qcom,tx-deamp_3_5db = <32>; - qcom,mpll = <5>; -}; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts index 27d9fc84b3..5ae1a3ec08 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts @@ -1,4 +1,4 @@ -#include "qcom-ipq8064-v2.0.dtsi" +#include "qcom-ipq8064-v2.0-smb208.dtsi" #include diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts index 998dad55c5..b33183d1a2 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts @@ -1,4 +1,4 @@ -#include "qcom-ipq8064-v2.0.dtsi" +#include "qcom-ipq8064-v2.0-smb208.dtsi" #include diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts index 04a2261929..c617064250 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts @@ -1,5 +1,5 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT -#include "qcom-ipq8064-v2.0.dtsi" +#include "qcom-ipq8064-v2.0-smb208.dtsi" #include @@ -159,9 +159,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - cs@0 { reg = <0>; compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts index 969ca724e3..c00f95f225 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts @@ -1,4 +1,4 @@ -#include "qcom-ipq8065.dtsi" +#include "qcom-ipq8065-smb208.dtsi" #include @@ -108,14 +108,14 @@ }; }; - mdio0_pins: mdio0_pins { + mdio0_pins: mdio0-pins { clk { pins = "gpio1"; input-disable; }; }; - rgmii2_pins: rgmii2_pins { + rgmii2_pins: rgmii2-pins { tx { pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ; input-disable; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-nighthawk.dtsi b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-nighthawk.dtsi index c899fa7c75..6c007e2c16 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-nighthawk.dtsi +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-nighthawk.dtsi @@ -1,4 +1,4 @@ -#include "qcom-ipq8065.dtsi" +#include "qcom-ipq8065-smb208.dtsi" #include @@ -124,14 +124,14 @@ }; }; - mdio0_pins: mdio0_pins { + mdio0_pins: mdio0-pins { clk { pins = "gpio1"; input-disable; }; }; - rgmii2_pins: rgmii2_pins { + rgmii2_pins: rgmii2-pins { tx { pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32"; @@ -223,9 +223,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - nand@0 { reg = <0>; compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-rt4230w-rev6.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-rt4230w-rev6.dts index 96163331f3..51ef2c3321 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-rt4230w-rev6.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-rt4230w-rev6.dts @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-or-later -#include "qcom-ipq8065.dtsi" +#include "qcom-ipq8065-smb208.dtsi" #include / { @@ -82,7 +82,7 @@ }; }; - rgmii2_pins: rgmii2_pins { + rgmii2_pins: rgmii2-pins { mux { pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62"; @@ -130,9 +130,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - nand@0 { reg = <0>; compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-tr4400-v2.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-tr4400-v2.dts index 871cc09502..9244639137 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-tr4400-v2.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-tr4400-v2.dts @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-or-later -#include "qcom-ipq8065.dtsi" +#include "qcom-ipq8065-smb208.dtsi" #include / { @@ -81,7 +81,7 @@ }; }; - rgmii2_pins: rgmii2_pins { + rgmii2_pins: rgmii2-pins { tx { pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32"; input-disable; @@ -119,9 +119,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - nand@0 { reg = <0>; compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065.dtsi b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065.dtsi deleted file mode 100644 index c70a5cbaed..0000000000 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065.dtsi +++ /dev/null @@ -1,167 +0,0 @@ -#include "qcom-ipq8064.dtsi" - -/ { - model = "Qualcomm IPQ8065"; - compatible = "qcom,ipq8065", "qcom,ipq8064"; - - aliases { - serial0 = &gsbi4_serial; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; -}; - -&gsbi4 { - qcom,mode = ; - status = "okay"; - - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ -}; - -&pcie0 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&pcie1 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&pcie2 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&sata { - ports-implemented = <0x1>; -}; - -&smb208_s2a { - regulator-min-microvolt = <775000>; - regulator-max-microvolt = <1275000>; -}; - -&smb208_s2b { - regulator-min-microvolt = <775000>; - regulator-max-microvolt = <1275000>; -}; - -&ss_phy_0 { - qcom,rx-eq = <2>; - qcom,tx-deamp_3_5db = <32>; - qcom,mpll = <5>; -}; - -&ss_phy_1 { - qcom,rx-eq = <2>; - qcom,tx-deamp_3_5db = <32>; - qcom,mpll = <5>; -}; - -&opp_table_l2 { - /delete-node/opp-1200000000; - - opp-1400000000 { - opp-hz = /bits/ 64 <1400000000>; - opp-microvolt = <1150000>; - clock-latency-ns = <100000>; - opp-level = <2>; - }; -}; - -&opp_table0 { - /* - * On ipq8065 1.2 ghz freq is not present - * Remove it to make cpufreq work and not - * complain for missing definition - */ - - /delete-node/opp-1200000000; - - /* - * Voltage thresholds are - */ - opp-384000000 { - opp-microvolt-speed0-pvs0-v0 = <975000 926250 1023750>; - opp-microvolt-speed0-pvs1-v0 = <950000 902500 997500>; - opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>; - opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>; - opp-microvolt-speed0-pvs4-v0 = <875000 831250 918750>; - opp-microvolt-speed0-pvs5-v0 = <825000 783750 866250>; - opp-microvolt-speed0-pvs6-v0 = <775000 736250 813750>; - }; - - opp-600000000 { - opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; - opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>; - opp-microvolt-speed0-pvs2-v0 = <950000 902500 997500>; - opp-microvolt-speed0-pvs3-v0 = <925000 878750 971250>; - opp-microvolt-speed0-pvs4-v0 = <900000 855000 945000>; - opp-microvolt-speed0-pvs5-v0 = <850000 807500 892500>; - opp-microvolt-speed0-pvs6-v0 = <800000 760000 840000>; - }; - - opp-800000000 { - opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; - opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; - opp-microvolt-speed0-pvs2-v0 = <1000000 950000 1050000>; - opp-microvolt-speed0-pvs3-v0 = <975000 926250 1023750>; - opp-microvolt-speed0-pvs4-v0 = <950000 902500 997500>; - opp-microvolt-speed0-pvs5-v0 = <900000 855000 945000>; - opp-microvolt-speed0-pvs6-v0 = <850000 807500 892500>; - }; - - opp-1000000000 { - opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; - opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; - opp-microvolt-speed0-pvs2-v0 = <1050000 997500 1102500>; - opp-microvolt-speed0-pvs3-v0 = <1025000 973750 1076250>; - opp-microvolt-speed0-pvs4-v0 = <1000000 950000 1050000>; - opp-microvolt-speed0-pvs5-v0 = <950000 902500 997500>; - opp-microvolt-speed0-pvs6-v0 = <900000 855000 945000>; - }; - - opp-1400000000 { - opp-microvolt-speed0-pvs0-v0 = <1175000 1116250 1233750>; - opp-microvolt-speed0-pvs1-v0 = <1150000 1092500 1207500>; - opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>; - opp-microvolt-speed0-pvs3-v0 = <1100000 1045000 1155000>; - opp-microvolt-speed0-pvs4-v0 = <1075000 1021250 1128750>; - opp-microvolt-speed0-pvs5-v0 = <1025000 973750 1076250>; - opp-microvolt-speed0-pvs6-v0 = <975000 926250 1023750>; - opp-level = <1>; - }; - - opp-1725000000 { - opp-hz = /bits/ 64 <1725000000>; - opp-microvolt-speed0-pvs0-v0 = <1262500 1199375 1325625>; - opp-microvolt-speed0-pvs1-v0 = <1225000 1163750 1286250>; - opp-microvolt-speed0-pvs2-v0 = <1200000 1140000 1260000>; - opp-microvolt-speed0-pvs3-v0 = <1175000 1116250 1233750>; - opp-microvolt-speed0-pvs4-v0 = <1150000 1092500 1207500>; - opp-microvolt-speed0-pvs5-v0 = <1100000 1045000 1155000>; - opp-microvolt-speed0-pvs6-v0 = <1050000 997500 1102500>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - opp-level = <2>; - }; -}; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8068-cryptid-common.dtsi b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8068-cryptid-common.dtsi index 141c71a8aa..93b9aa86f7 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8068-cryptid-common.dtsi +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8068-cryptid-common.dtsi @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0 OR MIT -#include "qcom-ipq8064-v2.0.dtsi" +#include "qcom-ipq8064-v2.0-smb208.dtsi" / { memory { @@ -140,9 +140,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - nand@0 { compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts index 85b0dc3b8c..574536cf55 100644 --- a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts @@ -1,4 +1,4 @@ -#include "qcom-ipq8064-v2.0.dtsi" +#include "qcom-ipq8064-v2.0-smb208.dtsi" #include #include @@ -262,9 +262,6 @@ &nand { status = "okay"; - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - nand@0 { compatible = "qcom,nandcs"; diff --git a/target/linux/ipq806x/patches-5.15/082-ipq8064-dtsi-tweaks.patch b/target/linux/ipq806x/patches-5.15/082-ipq8064-dtsi-tweaks.patch deleted file mode 100644 index 36be35fce1..0000000000 --- a/target/linux/ipq806x/patches-5.15/082-ipq8064-dtsi-tweaks.patch +++ /dev/null @@ -1,240 +0,0 @@ ---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi -@@ -352,6 +352,7 @@ - gpio-ranges = <&qcom_pinmux 0 0 69>; - #gpio-cells = <2>; - interrupt-controller; -+ #address-cells = <0>; - #interrupt-cells = <2>; - interrupts = ; - -@@ -379,6 +380,7 @@ - function = "pcie3_rst"; - drive-strength = <12>; - bias-disable; -+ output-low; - }; - }; - -@@ -411,12 +413,9 @@ - }; - - nand_pins: nand_pins { -- mux { -+ disable { - pins = "gpio34", "gpio35", "gpio36", -- "gpio37", "gpio38", "gpio39", -- "gpio40", "gpio41", "gpio42", -- "gpio43", "gpio44", "gpio45", -- "gpio46", "gpio47"; -+ "gpio37", "gpio38"; - function = "nand"; - drive-strength = <10>; - bias-disable; -@@ -424,6 +423,8 @@ - - pullups { - pins = "gpio39"; -+ function = "nand"; -+ drive-strength = <10>; - bias-pull-up; - }; - -@@ -431,6 +432,8 @@ - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; -+ function = "nand"; -+ drive-strength = <10>; - bias-bus-hold; - }; - }; -@@ -439,6 +442,7 @@ - intc: interrupt-controller@2000000 { - compatible = "qcom,msm-qgic2"; - interrupt-controller; -+ #address-cells = <0>; - #interrupt-cells = <3>; - reg = <0x02000000 0x1000>, - <0x02002000 0x1000>; -@@ -468,11 +472,13 @@ - acc0: clock-controller@2088000 { - compatible = "qcom,kpss-acc-v1"; - reg = <0x02088000 0x1000>, <0x02008000 0x1000>; -+ clock-output-names = "acpu0_aux"; - }; - - acc1: clock-controller@2098000 { - compatible = "qcom,kpss-acc-v1"; - reg = <0x02098000 0x1000>, <0x02008000 0x1000>; -+ clock-output-names = "acpu1_aux"; - }; - - adm_dma: dma-controller@18300000 { -@@ -496,13 +502,13 @@ - }; - - saw0: regulator@2089000 { -- compatible = "qcom,saw2"; -+ compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon"; - reg = <0x02089000 0x1000>, <0x02009000 0x1000>; - regulator; - }; - - saw1: regulator@2099000 { -- compatible = "qcom,saw2"; -+ compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon"; - reg = <0x02099000 0x1000>, <0x02009000 0x1000>; - regulator; - }; -@@ -530,7 +536,7 @@ - status = "disabled"; - }; - -- i2c@124a0000 { -+ gsbi2_i2c: i2c@124a0000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x124a0000 0x1000>; - interrupts = ; -@@ -676,9 +682,6 @@ - compatible = "qcom,ipq806x-nand"; - reg = <0x1ac00000 0x800>; - -- pinctrl-0 = <&nand_pins>; -- pinctrl-names = "default"; -- - clocks = <&gcc EBI2_CLK>, - <&gcc EBI2_AON_CLK>; - clock-names = "core", "aon"; -@@ -733,10 +736,13 @@ - tsens_calib_backup: calib_backup@410 { - reg = <0x410 0xb>; - }; -+ speedbin_efuse: speedbin@0c0 { -+ reg = <0x0c0 0x4>; -+ }; - }; - - gcc: clock-controller@900000 { -- compatible = "qcom,gcc-ipq8064"; -+ compatible = "qcom,gcc-ipq8064", "syscon"; - reg = <0x00900000 0x4000>; - #clock-cells = <1>; - #reset-cells = <1>; -@@ -768,10 +774,45 @@ - clocks = <&gcc RPM_MSG_RAM_H_CLK>; - clock-names = "ram"; - -+ #address-cells = <1>; -+ #size-cells = <0>; -+ - rpmcc: clock-controller { - compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; - #clock-cells = <1>; - }; -+ -+ regulators { -+ compatible = "qcom,rpm-smb208-regulators"; -+ -+ smb208_s1a: s1a { -+ regulator-min-microvolt = <1050000>; -+ regulator-max-microvolt = <1150000>; -+ -+ qcom,switch-mode-frequency = <1200000>; -+ }; -+ -+ smb208_s1b: s1b { -+ regulator-min-microvolt = <1050000>; -+ regulator-max-microvolt = <1150000>; -+ -+ qcom,switch-mode-frequency = <1200000>; -+ }; -+ -+ smb208_s2a: s2a { -+ regulator-min-microvolt = < 800000>; -+ regulator-max-microvolt = <1250000>; -+ -+ qcom,switch-mode-frequency = <1200000>; -+ }; -+ -+ smb208_s2b: s2b { -+ regulator-min-microvolt = < 800000>; -+ regulator-max-microvolt = <1250000>; -+ -+ qcom,switch-mode-frequency = <1200000>; -+ }; -+ }; - }; - - tcsr: syscon@1a400000 { -@@ -965,7 +1006,7 @@ - - gmac0: ethernet@37000000 { - device_type = "network"; -- compatible = "qcom,ipq806x-gmac"; -+ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; - reg = <0x37000000 0x200000>; - interrupts = ; - interrupt-names = "macirq"; -@@ -989,7 +1030,7 @@ - - gmac1: ethernet@37200000 { - device_type = "network"; -- compatible = "qcom,ipq806x-gmac"; -+ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; - reg = <0x37200000 0x200000>; - interrupts = ; - interrupt-names = "macirq"; -@@ -1013,7 +1054,7 @@ - - gmac2: ethernet@37400000 { - device_type = "network"; -- compatible = "qcom,ipq806x-gmac"; -+ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; - reg = <0x37400000 0x200000>; - interrupts = ; - interrupt-names = "macirq"; -@@ -1037,7 +1078,7 @@ - - gmac3: ethernet@37600000 { - device_type = "network"; -- compatible = "qcom,ipq806x-gmac"; -+ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; - reg = <0x37600000 0x200000>; - interrupts = ; - interrupt-names = "macirq"; -@@ -1065,8 +1106,6 @@ - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; -- -- status = "disabled"; - }; - - ss_phy_0: phy@100f8830 { -@@ -1075,8 +1114,6 @@ - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; -- -- status = "disabled"; - }; - - usb3_0: usb3@100f8800 { -@@ -1176,7 +1213,7 @@ - }; - - amba: amba { -- compatible = "simple-bus"; -+ compatible = "arm,amba-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; -@@ -1195,7 +1232,6 @@ - non-removable; - cap-sd-highspeed; - cap-mmc-highspeed; -- mmc-ddr-1_8v; - vmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; - dma-names = "tx", "rx"; diff --git a/target/linux/ipq806x/patches-5.15/083-ipq8064-dtsi-additions.patch b/target/linux/ipq806x/patches-5.15/083-ipq8064-dtsi-additions.patch deleted file mode 100644 index adc784fcfc..0000000000 --- a/target/linux/ipq806x/patches-5.15/083-ipq8064-dtsi-additions.patch +++ /dev/null @@ -1,371 +0,0 @@ ---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi -@@ -10,6 +10,8 @@ - #include - #include - #include -+#include -+#include - - / { - #address-cells = <1>; -@@ -30,6 +32,16 @@ - next-level-cache = <&L2>; - qcom,acc = <&acc0>; - qcom,saw = <&saw0>; -+ clocks = <&kraitcc 0>, <&kraitcc 4>; -+ clock-names = "cpu", "l2"; -+ clock-latency = <100000>; -+ cpu-supply = <&smb208_s2a>; -+ operating-points-v2 = <&opp_table0>; -+ voltage-tolerance = <5>; -+ cooling-min-state = <0>; -+ cooling-max-state = <10>; -+ #cooling-cells = <2>; -+ cpu-idle-states = <&CPU_SPC>; - }; - - cpu1: cpu@1 { -@@ -40,11 +52,125 @@ - next-level-cache = <&L2>; - qcom,acc = <&acc1>; - qcom,saw = <&saw1>; -+ clocks = <&kraitcc 1>, <&kraitcc 4>; -+ clock-names = "cpu", "l2"; -+ clock-latency = <100000>; -+ cpu-supply = <&smb208_s2b>; -+ operating-points-v2 = <&opp_table0>; -+ voltage-tolerance = <5>; -+ cooling-min-state = <0>; -+ cooling-max-state = <10>; -+ #cooling-cells = <2>; -+ cpu-idle-states = <&CPU_SPC>; -+ }; -+ -+ idle-states { -+ CPU_SPC: spc { -+ compatible = "qcom,idle-state-spc"; -+ status = "disabled"; -+ entry-latency-us = <400>; -+ exit-latency-us = <900>; -+ min-residency-us = <3000>; -+ }; - }; -+ }; - -- L2: l2-cache { -- compatible = "cache"; -- cache-level = <2>; -+ opp_table_l2: opp_table_l2 { -+ compatible = "operating-points-v2"; -+ -+ opp-384000000 { -+ opp-hz = /bits/ 64 <384000000>; -+ opp-microvolt = <1100000>; -+ clock-latency-ns = <100000>; -+ opp-level = <0>; -+ }; -+ -+ opp-1000000000 { -+ opp-hz = /bits/ 64 <1000000000>; -+ opp-microvolt = <1100000>; -+ clock-latency-ns = <100000>; -+ opp-level = <1>; -+ }; -+ -+ opp-1200000000 { -+ opp-hz = /bits/ 64 <1200000000>; -+ opp-microvolt = <1150000>; -+ clock-latency-ns = <100000>; -+ opp-level = <2>; -+ }; -+ }; -+ -+ opp_table0: opp_table0 { -+ compatible = "operating-points-v2-kryo-cpu"; -+ nvmem-cells = <&speedbin_efuse>; -+ -+ /* -+ * Voltage thresholds are -+ */ -+ opp-384000000 { -+ opp-hz = /bits/ 64 <384000000>; -+ opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; -+ opp-microvolt-speed0-pvs1-v0 = <925000 878750 971250>; -+ opp-microvolt-speed0-pvs2-v0 = <875000 831250 918750>; -+ opp-microvolt-speed0-pvs3-v0 = <800000 760000 840000>; -+ opp-supported-hw = <0x1>; -+ clock-latency-ns = <100000>; -+ opp-level = <0>; -+ }; -+ -+ opp-600000000 { -+ opp-hz = /bits/ 64 <600000000>; -+ opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; -+ opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>; -+ opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>; -+ opp-microvolt-speed0-pvs3-v0 = <850000 807500 892500>; -+ opp-supported-hw = <0x1>; -+ clock-latency-ns = <100000>; -+ opp-level = <1>; -+ }; -+ -+ opp-800000000 { -+ opp-hz = /bits/ 64 <800000000>; -+ opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; -+ opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; -+ opp-microvolt-speed0-pvs2-v0 = <995000 945250 1044750>; -+ opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>; -+ opp-supported-hw = <0x1>; -+ clock-latency-ns = <100000>; -+ opp-level = <1>; -+ }; -+ -+ opp-1000000000 { -+ opp-hz = /bits/ 64 <1000000000>; -+ opp-microvolt-speed0-pvs0-v0 = <1150000 1092500 1207500>; -+ opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; -+ opp-microvolt-speed0-pvs2-v0 = <1025000 973750 1076250>; -+ opp-microvolt-speed0-pvs3-v0 = <950000 902500 997500>; -+ opp-supported-hw = <0x1>; -+ clock-latency-ns = <100000>; -+ opp-level = <1>; -+ }; -+ -+ opp-1200000000 { -+ opp-hz = /bits/ 64 <1200000000>; -+ opp-microvolt-speed0-pvs0-v0 = <1200000 1140000 1260000>; -+ opp-microvolt-speed0-pvs1-v0 = <1125000 1068750 1181250>; -+ opp-microvolt-speed0-pvs2-v0 = <1075000 1021250 1128750>; -+ opp-microvolt-speed0-pvs3-v0 = <1000000 950000 1050000>; -+ opp-supported-hw = <0x1>; -+ clock-latency-ns = <100000>; -+ opp-level = <2>; -+ }; -+ -+ opp-1400000000 { -+ opp-hz = /bits/ 64 <1400000000>; -+ opp-microvolt-speed0-pvs0-v0 = <1250000 1187500 1312500>; -+ opp-microvolt-speed0-pvs1-v0 = <1175000 1116250 1233750>; -+ opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>; -+ opp-microvolt-speed0-pvs3-v0 = <1050000 997500 1102500>; -+ opp-supported-hw = <0x1>; -+ clock-latency-ns = <100000>; -+ opp-level = <2>; - }; - }; - -@@ -317,6 +443,15 @@ - }; - }; - -+ fab-scaling { -+ compatible = "qcom,fab-scaling"; -+ clocks = <&rpmcc RPM_APPS_FABRIC_A_CLK>, <&rpmcc RPM_EBI1_A_CLK>; -+ clock-names = "apps-fab-clk", "ddr-fab-clk"; -+ fab_freq_high = <533000000>; -+ fab_freq_nominal = <400000000>; -+ cpu_freq_threshold = <1000000000>; -+ }; -+ - firmware { - scm { - compatible = "qcom,scm-ipq806x", "qcom,scm"; -@@ -384,6 +519,15 @@ - }; - }; - -+ i2c4_pins: i2c4_pinmux { -+ mux { -+ pins = "gpio12", "gpio13"; -+ function = "gsbi4"; -+ drive-strength = <12>; -+ bias-disable; -+ }; -+ }; -+ - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; -@@ -437,6 +581,27 @@ - bias-bus-hold; - }; - }; -+ -+ mdio0_pins: mdio0_pins { -+ mux { -+ pins = "gpio0", "gpio1"; -+ function = "mdio"; -+ drive-strength = <8>; -+ bias-disable; -+ }; -+ }; -+ -+ rgmii2_pins: rgmii2_pins { -+ mux { -+ pins = "gpio27", "gpio28", "gpio29", -+ "gpio30", "gpio31", "gpio32", -+ "gpio51", "gpio52", "gpio59", -+ "gpio60", "gpio61", "gpio62"; -+ function = "rgmii2"; -+ drive-strength = <8>; -+ bias-disable; -+ }; -+ }; - }; - - intc: interrupt-controller@2000000 { -@@ -513,6 +678,17 @@ - regulator; - }; - -+ saw_l2: regulator@02012000 { -+ compatible = "qcom,saw2", "syscon"; -+ reg = <0x02012000 0x1000>; -+ regulator; -+ }; -+ -+ sic_non_secure: sic-non-secure@12100000 { -+ compatible = "syscon"; -+ reg = <0x12100000 0x10000>; -+ }; -+ - gsbi2: gsbi@12480000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <2>; -@@ -637,6 +813,33 @@ - }; - }; - -+ gsbi6: gsbi@16500000 { -+ status = "disabled"; -+ compatible = "qcom,gsbi-v1.0.0"; -+ cell-index = <6>; -+ reg = <0x16500000 0x100>; -+ clocks = <&gcc GSBI6_H_CLK>; -+ clock-names = "iface"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ ranges; -+ -+ syscon-tcsr = <&tcsr>; -+ -+ gsbi6_i2c: i2c@16580000 { -+ compatible = "qcom,i2c-qup-v1.1.1"; -+ reg = <0x16580000 0x1000>; -+ interrupts = ; -+ -+ clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>; -+ clock-names = "core", "iface"; -+ status = "disabled"; -+ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ }; -+ }; -+ - gsbi7: gsbi@16600000 { - status = "disabled"; - compatible = "qcom,gsbi-v1.0.0"; -@@ -658,6 +861,19 @@ - clock-names = "core", "iface"; - status = "disabled"; - }; -+ -+ gsbi7_i2c: i2c@16680000 { -+ compatible = "qcom,i2c-qup-v1.1.1"; -+ reg = <0x16680000 0x1000>; -+ interrupts = ; -+ -+ clocks = <&gcc GSBI7_QUP_CLK>, <&gcc GSBI7_H_CLK>; -+ clock-names = "core", "iface"; -+ status = "disabled"; -+ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ }; - }; - - rng@1a500000 { -@@ -761,6 +977,17 @@ - }; - }; - -+ L2: l2-cache { -+ compatible = "qcom,krait-cache", "cache"; -+ cache-level = <2>; -+ qcom,saw = <&saw_l2>; -+ -+ clocks = <&kraitcc 4>; -+ clock-names = "l2"; -+ l2-supply = <&smb208_s1a>; -+ operating-points-v2 = <&opp_table_l2>; -+ }; -+ - rpm: rpm@108000 { - compatible = "qcom,rpm-ipq8064"; - reg = <0x108000 0x1000>; -@@ -828,6 +1055,11 @@ - clock-output-names = "acpu_l2_aux"; - }; - -+ kraitcc: clock-controller { -+ compatible = "qcom,krait-cc-v1"; -+ #clock-cells = <1>; -+ }; -+ - lcc: clock-controller@28000000 { - compatible = "qcom,lcc-ipq8064"; - reg = <0x28000000 0x1000>; -@@ -835,6 +1067,11 @@ - #reset-cells = <1>; - }; - -+ sfpb_mutex_block: syscon@1200600 { -+ compatible = "syscon"; -+ reg = <0x01200600 0x100>; -+ }; -+ - pcie0: pci@1b500000 { - compatible = "qcom,pcie-ipq8064"; - reg = <0x1b500000 0x1000 -@@ -1184,6 +1421,21 @@ - }; - }; - -+ -+ mdio0: mdio@37000000 { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ compatible = "qcom,ipq8064-mdio", "syscon"; -+ reg = <0x37000000 0x200000>; -+ resets = <&gcc GMAC_CORE1_RESET>; -+ reset-names = "stmmaceth"; -+ clocks = <&gcc GMAC_CORE1_CLK>; -+ clock-names = "stmmaceth"; -+ -+ status = "disabled"; -+ }; -+ - vsdcc_fixed: vsdcc-regulator { - compatible = "regulator-fixed"; - regulator-name = "SDCC Power"; -@@ -1258,4 +1510,17 @@ - }; - }; - }; -+ -+ sfpb_mutex: sfpb-mutex { -+ compatible = "qcom,sfpb-mutex"; -+ syscon = <&sfpb_mutex_block 4 4>; -+ -+ #hwlock-cells = <1>; -+ }; -+ -+ smem { -+ compatible = "qcom,smem"; -+ memory-region = <&smem>; -+ hwlocks = <&sfpb_mutex 3>; -+ }; - }; diff --git a/target/linux/ipq806x/patches-5.15/084-ipq8064-v1.0-dtsi-cleanup.patch b/target/linux/ipq806x/patches-5.15/084-ipq8064-v1.0-dtsi-cleanup.patch deleted file mode 100644 index 44323a1561..0000000000 --- a/target/linux/ipq806x/patches-5.15/084-ipq8064-v1.0-dtsi-cleanup.patch +++ /dev/null @@ -1,89 +0,0 @@ -This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches -instead of keeping a local version. -We drop partitions, LEDs and keys from the file as we will implement -them differently anyway. - ---- a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi -@@ -42,16 +42,6 @@ - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; -- -- partition@0 { -- label = "rootfs"; -- reg = <0x0 0x1000000>; -- }; -- -- partition@1 { -- label = "scratch"; -- reg = <0x1000000 0x1000000>; -- }; - }; - }; - }; -@@ -64,64 +54,5 @@ - ports-implemented = <0x1>; - status = "okay"; - }; -- -- gpio_keys { -- compatible = "gpio-keys"; -- pinctrl-0 = <&buttons_pins>; -- pinctrl-names = "default"; -- -- button@1 { -- label = "reset"; -- linux,code = ; -- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; -- linux,input-type = <1>; -- debounce-interval = <60>; -- }; -- button@2 { -- label = "wps"; -- linux,code = ; -- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; -- linux,input-type = <1>; -- debounce-interval = <60>; -- }; -- }; -- -- leds { -- compatible = "gpio-leds"; -- pinctrl-0 = <&leds_pins>; -- pinctrl-names = "default"; -- -- led@7 { -- label = "led_usb1"; -- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; -- linux,default-trigger = "usbdev"; -- default-state = "off"; -- }; -- -- led@8 { -- label = "led_usb3"; -- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; -- linux,default-trigger = "usbdev"; -- default-state = "off"; -- }; -- -- led@9 { -- label = "status_led_fail"; -- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; -- default-state = "off"; -- }; -- -- led@26 { -- label = "sata_led"; -- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; -- default-state = "off"; -- }; -- -- led@53 { -- label = "status_led_pass"; -- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; -- default-state = "off"; -- }; -- }; - }; - }; diff --git a/target/linux/ipq806x/patches-5.15/085-ipq8064-v1.0-dtsi-additions.patch b/target/linux/ipq806x/patches-5.15/085-ipq8064-v1.0-dtsi-additions.patch deleted file mode 100644 index 58f6a46e4f..0000000000 --- a/target/linux/ipq806x/patches-5.15/085-ipq8064-v1.0-dtsi-additions.patch +++ /dev/null @@ -1,14 +0,0 @@ -This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches -instead of keeping a local version. This patch adds our local adjustments -for the (local) additional contents of qcom-ipq8064.dtsi - ---- a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi -@@ -56,3 +56,7 @@ - }; - }; - }; -+ -+&CPU_SPC { -+ status = "okay"; -+}; diff --git a/target/linux/ipq806x/patches-5.15/086-ipq8064-fix-duplicate-node.patch b/target/linux/ipq806x/patches-5.15/086-ipq8064-fix-duplicate-node.patch deleted file mode 100644 index e4aefe171a..0000000000 --- a/target/linux/ipq806x/patches-5.15/086-ipq8064-fix-duplicate-node.patch +++ /dev/null @@ -1,145 +0,0 @@ ---- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts -+++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts -@@ -24,73 +24,6 @@ - device_type = "memory"; - }; - -- mdio0: mdio-0 { -- status = "okay"; -- compatible = "virtual,mdio-gpio"; -- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, -- <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; -- #address-cells = <1>; -- #size-cells = <0>; -- -- pinctrl-0 = <&mdio0_pins>; -- pinctrl-names = "default"; -- -- switch0: switch@10 { -- compatible = "qca,qca8337"; -- #address-cells = <1>; -- #size-cells = <0>; -- -- dsa,member = <0 0>; -- -- pinctrl-0 = <&sw0_reset_pin>; -- pinctrl-names = "default"; -- -- reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; -- reg = <0x10>; -- -- ports { -- #address-cells = <1>; -- #size-cells = <0>; -- -- switch0cpu: port@0 { -- reg = <0>; -- label = "cpu"; -- ethernet = <&gmac0>; -- phy-mode = "rgmii-id"; -- fixed-link { -- speed = <1000>; -- full-duplex; -- }; -- }; -- -- port@1 { -- reg = <1>; -- label = "sw1"; -- }; -- -- port@2 { -- reg = <2>; -- label = "sw2"; -- }; -- -- port@3 { -- reg = <3>; -- label = "sw3"; -- }; -- -- port@4 { -- reg = <4>; -- label = "sw4"; -- }; -- -- port@5 { -- reg = <5>; -- label = "sw5"; -- }; -- }; -- }; -- }; -- - mdio1: mdio-1 { - status = "okay"; - compatible = "virtual,mdio-gpio"; -@@ -220,6 +153,68 @@ - status = "okay"; - }; - -+&mdio0 { -+ status = "okay"; -+ -+ pinctrl-0 = <&mdio0_pins>; -+ pinctrl-names = "default"; -+ -+ switch0: switch@10 { -+ compatible = "qca,qca8337"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ dsa,member = <0 0>; -+ -+ pinctrl-0 = <&sw0_reset_pin>; -+ pinctrl-names = "default"; -+ -+ reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; -+ reg = <0x10>; -+ -+ ports { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ switch0cpu: port@0 { -+ reg = <0>; -+ label = "cpu"; -+ ethernet = <&gmac0>; -+ phy-mode = "rgmii-id"; -+ fixed-link { -+ speed = <1000>; -+ full-duplex; -+ }; -+ }; -+ -+ port@1 { -+ reg = <1>; -+ label = "sw1"; -+ }; -+ -+ port@2 { -+ reg = <2>; -+ label = "sw2"; -+ }; -+ -+ port@3 { -+ reg = <3>; -+ label = "sw3"; -+ }; -+ -+ port@4 { -+ reg = <4>; -+ label = "sw4"; -+ }; -+ -+ port@5 { -+ reg = <5>; -+ label = "sw5"; -+ }; -+ }; -+ }; -+}; -+ - &gmac0 { - status = "okay"; - diff --git a/target/linux/ipq806x/patches-5.15/103-01-ARM-dts-qcom-replace-gcc-PXO-with-pxo_board-fixed.patch b/target/linux/ipq806x/patches-5.15/103-01-ARM-dts-qcom-replace-gcc-PXO-with-pxo_board-fixed.patch new file mode 100644 index 0000000000..0c25062214 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/103-01-ARM-dts-qcom-replace-gcc-PXO-with-pxo_board-fixed.patch @@ -0,0 +1,36 @@ +From 5a8aa766cedac0ceaa4beabc30e9fa62dd9f1ac1 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 29 Apr 2022 14:23:16 +0200 +Subject: [PATCH v2 1/2] ARM: dts: qcom: replace gcc PXO with pxo_board fixed + clock + +Replace gcc PXO phandle to pxo_board fixed clock declared in the dts. +gcc driver doesn't provide PXO_SRC as it's a fixed-clock. This cause a +kernel panic if any driver actually try to use it. + +Fixes: 40cf5c884a96 ("ARM: dts: qcom: add L2CC and RPM for IPQ8064") +Signed-off-by: Ansuel Smith +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 4 ++-- + 1 file changed, 2 insertions(+), 2 deletions(-) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -304,7 +304,7 @@ + clock-frequency = <25000000>; + }; + +- pxo_board { ++ pxo_board: pxo_board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; +@@ -782,7 +782,7 @@ + l2cc: clock-controller@2011000 { + compatible = "qcom,kpss-gcc", "syscon"; + reg = <0x2011000 0x1000>; +- clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>; ++ clocks = <&gcc PLL8_VOTE>, <&pxo_board>; + clock-names = "pll8_vote", "pxo"; + clock-output-names = "acpu_l2_aux"; + }; diff --git a/target/linux/ipq806x/patches-5.15/103-ARM-dts-qcom-reduce-pci-IO-size-to-64K.patch b/target/linux/ipq806x/patches-5.15/103-ARM-dts-qcom-reduce-pci-IO-size-to-64K.patch deleted file mode 100644 index 1f61fdf886..0000000000 --- a/target/linux/ipq806x/patches-5.15/103-ARM-dts-qcom-reduce-pci-IO-size-to-64K.patch +++ /dev/null @@ -1,46 +0,0 @@ -From 84909e85881d67244240c9f40974ce12a51e3886 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Tue, 11 May 2021 23:09:45 +0200 -Subject: [PATCH] ARM: dts: qcom: reduce pci IO size to 64K - -The current value is probably a typo and is actually uncommon to find -1MB IO space even on a x86 arch. Also with recent changes to the pci -driver, pci1 and pci2 now fails to function as any connected device -fails any reg read/write. Reduce this to 64K as it should be more than -enough and 3 * 64K of total IO space doesn't exceed the IO_SPACE_LIMIT -hardcoded for the ARM arch. - -Signed-off-by: Ansuel Smith ---- - arch/arm/boot/dts/qcom-ipq8064.dtsi | 6 +++--- - 1 file changed, 3 insertions(+), 3 deletions(-) - ---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi -@@ -1086,7 +1086,7 @@ - #address-cells = <3>; - #size-cells = <2>; - -- ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */ -+ ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */ - - interrupts = ; -@@ -1137,7 +1137,7 @@ - #address-cells = <3>; - #size-cells = <2>; - -- ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */ -+ ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */ - - interrupts = ; -@@ -1188,7 +1188,7 @@ - #address-cells = <3>; - #size-cells = <2>; - -- ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */ -+ ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */ - - interrupts = ; diff --git a/target/linux/ipq806x/patches-5.15/103-v5.19-02-ARM-dts-qcom-add-syscon-and-cxo-pxo-clock-to-gcc-.patch b/target/linux/ipq806x/patches-5.15/103-v5.19-02-ARM-dts-qcom-add-syscon-and-cxo-pxo-clock-to-gcc-.patch new file mode 100644 index 0000000000..db23af128f --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/103-v5.19-02-ARM-dts-qcom-add-syscon-and-cxo-pxo-clock-to-gcc-.patch @@ -0,0 +1,39 @@ +From 9fa82f98cb85e5432060f469253adcf14fa38082 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Mon, 17 Jan 2022 21:59:39 +0100 +Subject: [PATCH v2 2/2] ARM: dts: qcom: add syscon and cxo/pxo clock to gcc + node for ipq8064 + +Add syscon compatible required for tsens driver to correctly probe driver +and access the reg. Also add cxo and pxo tag and declare them as gcc clock +now requires them for the ipq8064 gcc driver that has now been modernized. + +Signed-off-by: Ansuel Smith +Reviewed-by: Bjorn Andersson +Reviewed-by: Stephen Boyd +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 6 ++++-- + 1 file changed, 4 insertions(+), 2 deletions(-) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -298,7 +298,7 @@ + }; + + clocks { +- cxo_board { ++ cxo_board: cxo_board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; +@@ -736,7 +736,9 @@ + }; + + gcc: clock-controller@900000 { +- compatible = "qcom,gcc-ipq8064"; ++ compatible = "qcom,gcc-ipq8064", "syscon"; ++ clocks = <&pxo_board>, <&cxo_board>; ++ clock-names = "pxo", "cxo"; + reg = <0x00900000 0x4000>; + #clock-cells = <1>; + #reset-cells = <1>; diff --git a/target/linux/ipq806x/patches-5.15/104-v6.0-01-ARM-dts-qcom-ipq8064-add-multiple-missing-pin-defini.patch b/target/linux/ipq806x/patches-5.15/104-v6.0-01-ARM-dts-qcom-ipq8064-add-multiple-missing-pin-defini.patch new file mode 100644 index 0000000000..5dad164e3c --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-v6.0-01-ARM-dts-qcom-ipq8064-add-multiple-missing-pin-defini.patch @@ -0,0 +1,101 @@ +From 4af1defb305798d1a064a5ea0d0c9b30e5eee185 Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 7 Jul 2022 03:09:35 +0200 +Subject: [PATCH 1/8] ARM: dts: qcom: ipq8064: add multiple missing pin + definition + +Add missing definition for mdio0 pins used for gpio-bitbang driver,i2c4 +pins and rgmii2 pins for ipq8064. + +Drop i2c4_pins node from ipq8064-ap148 dts as it's now moved to ipq8064 +dtsi. + +Drop mdio0_pins node from ipq8064-rb3011 dts as it's now moved to +ipq8064 dtsi. + +Signed-off-by: Christian Marangi +Tested-by: Jonathan McDowell +Signed-off-by: Bjorn Andersson +Link: https://lore.kernel.org/r/20220707010943.20857-2-ansuelsmth@gmail.com +--- + arch/arm/boot/dts/qcom-ipq8064-ap148.dts | 6 ----- + arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 9 ------- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 32 +++++++++++++++++++++++ + 3 files changed, 32 insertions(+), 15 deletions(-) + +--- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts ++++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts +@@ -305,15 +305,6 @@ + }; + }; + +- mdio0_pins: mdio0_pins { +- mux { +- pins = "gpio0", "gpio1"; +- function = "gpio"; +- drive-strength = <8>; +- bias-disable; +- }; +- }; +- + mdio1_pins: mdio1_pins { + mux { + pins = "gpio10", "gpio11"; +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -382,6 +382,13 @@ + }; + }; + ++ i2c4_pins: i2c4-default { ++ pins = "gpio12", "gpio13"; ++ function = "gsbi4"; ++ drive-strength = <12>; ++ bias-disable; ++ }; ++ + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; +@@ -424,6 +431,8 @@ + + pullups { + pins = "gpio39"; ++ function = "nand"; ++ drive-strength = <10>; + bias-pull-up; + }; + +@@ -431,9 +440,32 @@ + pins = "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; ++ function = "nand"; ++ drive-strength = <10>; + bias-bus-hold; + }; + }; ++ ++ mdio0_pins: mdio0-pins { ++ mux { ++ pins = "gpio0", "gpio1"; ++ function = "mdio"; ++ drive-strength = <8>; ++ bias-disable; ++ }; ++ }; ++ ++ rgmii2_pins: rgmii2-pins { ++ mux { ++ pins = "gpio27", "gpio28", "gpio29", ++ "gpio30", "gpio31", "gpio32", ++ "gpio51", "gpio52", "gpio59", ++ "gpio60", "gpio61", "gpio62"; ++ function = "rgmii2"; ++ drive-strength = <8>; ++ bias-disable; ++ }; ++ }; + }; + + intc: interrupt-controller@2000000 { diff --git a/target/linux/ipq806x/patches-5.15/104-v6.0-02-ARM-dts-qcom-ipq8064-add-gsbi6-missing-definition.patch b/target/linux/ipq806x/patches-5.15/104-v6.0-02-ARM-dts-qcom-ipq8064-add-gsbi6-missing-definition.patch new file mode 100644 index 0000000000..1f4e288fb8 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-v6.0-02-ARM-dts-qcom-ipq8064-add-gsbi6-missing-definition.patch @@ -0,0 +1,67 @@ +From d883a12a547b6d42e795ff3b5ac87cfd013b5423 Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 7 Jul 2022 03:09:36 +0200 +Subject: [PATCH 2/8] ARM: dts: qcom: ipq8064: add gsbi6 missing definition + +Add gsbi6 missing definition for ipq8064. + +Signed-off-by: Christian Marangi +Tested-by: Jonathan McDowell +Signed-off-by: Bjorn Andersson +Link: https://lore.kernel.org/r/20220707010943.20857-3-ansuelsmth@gmail.com +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 43 +++++++++++++++++++++++++++++ + 1 file changed, 43 insertions(+) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -663,6 +663,49 @@ + }; + }; + ++ gsbi6: gsbi@16500000 { ++ compatible = "qcom,gsbi-v1.0.0"; ++ reg = <0x16500000 0x100>; ++ cell-index = <6>; ++ clocks = <&gcc GSBI6_H_CLK>; ++ clock-names = "iface"; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ranges; ++ ++ syscon-tcsr = <&tcsr>; ++ ++ status = "disabled"; ++ ++ gsbi6_i2c: i2c@16580000 { ++ compatible = "qcom,i2c-qup-v1.1.1"; ++ reg = <0x16580000 0x1000>; ++ interrupts = ; ++ ++ clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>; ++ clock-names = "core", "iface"; ++ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "disabled"; ++ }; ++ ++ gsbi6_spi: spi@16580000 { ++ compatible = "qcom,spi-qup-v1.1.1"; ++ reg = <0x16580000 0x1000>; ++ interrupts = ; ++ ++ clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>; ++ clock-names = "core", "iface"; ++ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "disabled"; ++ }; ++ }; ++ + gsbi7: gsbi@16600000 { + status = "disabled"; + compatible = "qcom,gsbi-v1.0.0"; diff --git a/target/linux/ipq806x/patches-5.15/104-v6.0-03-ARM-dts-qcom-ipq8064-add-specific-dtsi-with-smb208-r.patch b/target/linux/ipq806x/patches-5.15/104-v6.0-03-ARM-dts-qcom-ipq8064-add-specific-dtsi-with-smb208-r.patch new file mode 100644 index 0000000000..dbba722caa --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-v6.0-03-ARM-dts-qcom-ipq8064-add-specific-dtsi-with-smb208-r.patch @@ -0,0 +1,66 @@ +From 5c47a46d5e942ea6b041c8b7727b201817c1ff76 Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 7 Jul 2022 03:09:37 +0200 +Subject: [PATCH 3/8] ARM: dts: qcom: ipq8064: add specific dtsi with smb208 + rpm regulators + +Add specific ipq8064 dtsi with smb208 rpm regulators. + +Qcom advise to use this configuration but it's not mandatory and OEM +can decide to implement their own regulators. +smb208 regulators are used to scale CPU voltage, L2 cache voltage and +Ubi32 cores. + +There regulators are controlled by rpm and to correctly works gsbi4-i2c +require to be NEVER disabled or rpm will reject any regulator change +request. + +Signed-off-by: Christian Marangi +Tested-by: Jonathan McDowell +Signed-off-by: Bjorn Andersson +Link: https://lore.kernel.org/r/20220707010943.20857-4-ansuelsmth@gmail.com +--- + arch/arm/boot/dts/qcom-ipq8064-smb208.dtsi | 37 ++++++++++++++++++++++ + 1 file changed, 37 insertions(+) + create mode 100644 arch/arm/boot/dts/qcom-ipq8064-smb208.dtsi + +--- /dev/null ++++ b/arch/arm/boot/dts/qcom-ipq8064-smb208.dtsi +@@ -0,0 +1,37 @@ ++// SPDX-License-Identifier: GPL-2.0 ++ ++#include "qcom-ipq8064.dtsi" ++ ++&rpm { ++ smb208_regulators: regulators { ++ compatible = "qcom,rpm-smb208-regulators"; ++ ++ smb208_s1a: s1a { ++ regulator-min-microvolt = <1050000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s1b: s1b { ++ regulator-min-microvolt = <1050000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s2a: s2a { ++ regulator-min-microvolt = < 800000>; ++ regulator-max-microvolt = <1250000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s2b: s2b { ++ regulator-min-microvolt = < 800000>; ++ regulator-max-microvolt = <1250000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ }; ++}; diff --git a/target/linux/ipq806x/patches-5.15/104-v6.0-04-ARM-dts-qcom-ipq8064-add-missing-snps-dwmac-compatib.patch b/target/linux/ipq806x/patches-5.15/104-v6.0-04-ARM-dts-qcom-ipq8064-add-missing-snps-dwmac-compatib.patch new file mode 100644 index 0000000000..1a3185f500 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-v6.0-04-ARM-dts-qcom-ipq8064-add-missing-snps-dwmac-compatib.patch @@ -0,0 +1,56 @@ +From 0ce34e0c13e99c239cce6099f64b0e95697f36b1 Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 7 Jul 2022 03:09:38 +0200 +Subject: [PATCH 4/8] ARM: dts: qcom: ipq8064: add missing snps,dwmac + compatible for gmac + +Add missing snps,dwmac compatible for gmac ipq8064 dtsi. + +Signed-off-by: Christian Marangi +Tested-by: Jonathan McDowell +Reviewed-by: Krzysztof Kozlowski +Reviewed-by: Konrad Dybcio +Signed-off-by: Bjorn Andersson +Link: https://lore.kernel.org/r/20220707010943.20857-5-ansuelsmth@gmail.com +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 8 ++++---- + 1 file changed, 4 insertions(+), 4 deletions(-) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -1042,7 +1042,7 @@ + + gmac0: ethernet@37000000 { + device_type = "network"; +- compatible = "qcom,ipq806x-gmac"; ++ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; + reg = <0x37000000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; +@@ -1066,7 +1066,7 @@ + + gmac1: ethernet@37200000 { + device_type = "network"; +- compatible = "qcom,ipq806x-gmac"; ++ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; + reg = <0x37200000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; +@@ -1090,7 +1090,7 @@ + + gmac2: ethernet@37400000 { + device_type = "network"; +- compatible = "qcom,ipq806x-gmac"; ++ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; + reg = <0x37400000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; +@@ -1114,7 +1114,7 @@ + + gmac3: ethernet@37600000 { + device_type = "network"; +- compatible = "qcom,ipq806x-gmac"; ++ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; + reg = <0x37600000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; diff --git a/target/linux/ipq806x/patches-5.15/104-v6.0-05-ARM-dts-qcom-ipq8064-disable-usb-phy-by-default.patch b/target/linux/ipq806x/patches-5.15/104-v6.0-05-ARM-dts-qcom-ipq8064-disable-usb-phy-by-default.patch new file mode 100644 index 0000000000..43dac4b7fa --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-v6.0-05-ARM-dts-qcom-ipq8064-disable-usb-phy-by-default.patch @@ -0,0 +1,37 @@ +From d63d3124c0a5cdbe8b91d81b922fe56b2462e1b9 Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 7 Jul 2022 03:09:39 +0200 +Subject: [PATCH 5/8] ARM: dts: qcom: ipq8064: disable usb phy by default + +Disable usb phy by default. When the usb phy were pushed, half of them +were flagged as disabled by mistake. +Correctly disable all usb phy and enable them only if a device actually +use them. + +Signed-off-by: Christian Marangi +Signed-off-by: Bjorn Andersson +Link: https://lore.kernel.org/r/20220707010943.20857-6-ansuelsmth@gmail.com +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 4 ++++ + 1 file changed, 4 insertions(+) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -1188,6 +1188,8 @@ + clocks = <&gcc USB30_1_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; ++ ++ status = "disabled"; + }; + + ss_phy_1: phy@110f8830 { +@@ -1196,6 +1198,8 @@ + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; ++ ++ status = "disabled"; + }; + + usb3_1: usb3@110f8800 { diff --git a/target/linux/ipq806x/patches-5.15/104-v6.0-06-ARM-dts-qcom-ipq8064-reduce-pci-IO-size-to-64K.patch b/target/linux/ipq806x/patches-5.15/104-v6.0-06-ARM-dts-qcom-ipq8064-reduce-pci-IO-size-to-64K.patch new file mode 100644 index 0000000000..b1fca01c5e --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-v6.0-06-ARM-dts-qcom-ipq8064-reduce-pci-IO-size-to-64K.patch @@ -0,0 +1,51 @@ +From 8fafb7e5c041814876266259e5e439f93571dcef Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 7 Jul 2022 03:09:40 +0200 +Subject: [PATCH 6/8] ARM: dts: qcom: ipq8064: reduce pci IO size to 64K + +The current value for pci IO is problematic for ath10k wifi card +commonly connected to ipq8064 SoC. +The current value is probably a typo and is actually uncommon to find +1MB IO space even on a x86 arch. Also with recent changes to the pci +driver, pci1 and pci2 now fails to function as any connected device +fails any reg read/write. Reduce this to 64K as it should be more than +enough and 3 * 64K of total IO space doesn't exceed the IO_SPACE_LIMIT +hardcoded for the ARM arch. + +Signed-off-by: Christian Marangi +Tested-by: Jonathan McDowell +Signed-off-by: Bjorn Andersson +Link: https://lore.kernel.org/r/20220707010943.20857-7-ansuelsmth@gmail.com +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 6 +++--- + 1 file changed, 3 insertions(+), 3 deletions(-) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -885,7 +885,7 @@ + #address-cells = <3>; + #size-cells = <2>; + +- ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */ ++ ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */ + + interrupts = ; +@@ -936,7 +936,7 @@ + #address-cells = <3>; + #size-cells = <2>; + +- ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */ ++ ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */ + + interrupts = ; +@@ -987,7 +987,7 @@ + #address-cells = <3>; + #size-cells = <2>; + +- ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */ ++ ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */ + + interrupts = ; diff --git a/target/linux/ipq806x/patches-5.15/104-v6.0-07-ARM-dts-qcom-ipq8064-fix-and-add-some-missing-gsbi-n.patch b/target/linux/ipq806x/patches-5.15/104-v6.0-07-ARM-dts-qcom-ipq8064-fix-and-add-some-missing-gsbi-n.patch new file mode 100644 index 0000000000..ca5e5aa3c4 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-v6.0-07-ARM-dts-qcom-ipq8064-fix-and-add-some-missing-gsbi-n.patch @@ -0,0 +1,94 @@ +From 6c421a9c08286389bb331fe783e2625c9efcc187 Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 7 Jul 2022 03:09:41 +0200 +Subject: [PATCH 7/8] ARM: dts: qcom: ipq8064: fix and add some missing gsbi + node + +Add some tag for gsbi to make them usable for ipq8064 SoC. Add missing +gsbi7 i2c node and gsbi1 node. + +Signed-off-by: Christian Marangi +Tested-by: Jonathan McDowell +Signed-off-by: Bjorn Andersson +Link: https://lore.kernel.org/r/20220707010943.20857-8-ansuelsmth@gmail.com +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 54 ++++++++++++++++++++++++++++- + 1 file changed, 53 insertions(+), 1 deletion(-) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -539,6 +539,44 @@ + regulator; + }; + ++ gsbi1: gsbi@12440000 { ++ compatible = "qcom,gsbi-v1.0.0"; ++ reg = <0x12440000 0x100>; ++ cell-index = <1>; ++ clocks = <&gcc GSBI1_H_CLK>; ++ clock-names = "iface"; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ranges; ++ ++ syscon-tcsr = <&tcsr>; ++ ++ status = "disabled"; ++ ++ gsbi1_serial: serial@12450000 { ++ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; ++ reg = <0x12450000 0x100>, ++ <0x12400000 0x03>; ++ interrupts = ; ++ clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>; ++ clock-names = "core", "iface"; ++ ++ status = "disabled"; ++ }; ++ ++ gsbi1_i2c: i2c@12460000 { ++ compatible = "qcom,i2c-qup-v1.1.1"; ++ reg = <0x12460000 0x1000>; ++ interrupts = ; ++ clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; ++ clock-names = "core", "iface"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "disabled"; ++ }; ++ }; ++ + gsbi2: gsbi@12480000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <2>; +@@ -562,7 +600,7 @@ + status = "disabled"; + }; + +- i2c@124a0000 { ++ gsbi2_i2c: i2c@124a0000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x124a0000 0x1000>; + interrupts = ; +@@ -727,6 +765,20 @@ + clock-names = "core", "iface"; + status = "disabled"; + }; ++ ++ gsbi7_i2c: i2c@16680000 { ++ compatible = "qcom,i2c-qup-v1.1.1"; ++ reg = <0x16680000 0x1000>; ++ interrupts = ; ++ ++ clocks = <&gcc GSBI7_QUP_CLK>, <&gcc GSBI7_H_CLK>; ++ clock-names = "core", "iface"; ++ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "disabled"; ++ }; + }; + + rng@1a500000 { diff --git a/target/linux/ipq806x/patches-5.15/104-v6.0-08-ARM-dts-qcom-ipq8064-add-speedbin-efuse-nvmem-node.patch b/target/linux/ipq806x/patches-5.15/104-v6.0-08-ARM-dts-qcom-ipq8064-add-speedbin-efuse-nvmem-node.patch new file mode 100644 index 0000000000..463c3d4a65 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-v6.0-08-ARM-dts-qcom-ipq8064-add-speedbin-efuse-nvmem-node.patch @@ -0,0 +1,28 @@ +From 7f5aecdd4ffcc018f73171bc0e028cd4e3361acd Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 7 Jul 2022 03:09:43 +0200 +Subject: [PATCH 8/8] ARM: dts: qcom: ipq8064: add speedbin efuse nvmem node + +Add speedbin efuse nvmem cell needed for the opp table for the CPU +freqs. + +Signed-off-by: Christian Marangi +Tested-by: Jonathan McDowell +Signed-off-by: Bjorn Andersson +Link: https://lore.kernel.org/r/20220707010943.20857-10-ansuelsmth@gmail.com +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -854,6 +854,9 @@ + reg = <0x00700000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; ++ speedbin_efuse: speedbin@c0 { ++ reg = <0xc0 0x4>; ++ }; + tsens_calib: calib@400 { + reg = <0x400 0xb>; + }; diff --git a/target/linux/ipq806x/patches-5.15/105-v6.0-01-hwspinlock-qcom-Add-support-for-mmio-usage-to-sfpb-m.patch b/target/linux/ipq806x/patches-5.15/105-v6.0-01-hwspinlock-qcom-Add-support-for-mmio-usage-to-sfpb-m.patch new file mode 100644 index 0000000000..2c6f6b10c4 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/105-v6.0-01-hwspinlock-qcom-Add-support-for-mmio-usage-to-sfpb-m.patch @@ -0,0 +1,71 @@ +From cdab30b44518513003607ecfc8a22de3dbbb78ed Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 7 Jul 2022 12:20:38 +0200 +Subject: [PATCH 1/1] hwspinlock: qcom: Add support for mmio usage to + sfpb-mutex + +Allow sfpb-mutex to use mmio in addition to syscon. + +Signed-off-by: Christian Marangi +Reviewed-by: Bjorn Andersson +Signed-off-by: Bjorn Andersson +Link: https://lore.kernel.org/r/20220707102040.1859-1-ansuelsmth@gmail.com +--- + drivers/hwspinlock/qcom_hwspinlock.c | 28 +++++++++++++++++++++++----- + 1 file changed, 23 insertions(+), 5 deletions(-) + +--- a/drivers/hwspinlock/qcom_hwspinlock.c ++++ b/drivers/hwspinlock/qcom_hwspinlock.c +@@ -19,6 +19,11 @@ + #define QCOM_MUTEX_APPS_PROC_ID 1 + #define QCOM_MUTEX_NUM_LOCKS 32 + ++struct qcom_hwspinlock_of_data { ++ u32 offset; ++ u32 stride; ++}; ++ + static int qcom_hwspinlock_trylock(struct hwspinlock *lock) + { + struct regmap_field *field = lock->priv; +@@ -63,9 +68,20 @@ static const struct hwspinlock_ops qcom_ + .unlock = qcom_hwspinlock_unlock, + }; + ++static const struct qcom_hwspinlock_of_data of_sfpb_mutex = { ++ .offset = 0x4, ++ .stride = 0x4, ++}; ++ ++/* All modern platform has offset 0 and stride of 4k */ ++static const struct qcom_hwspinlock_of_data of_tcsr_mutex = { ++ .offset = 0, ++ .stride = 0x1000, ++}; ++ + static const struct of_device_id qcom_hwspinlock_of_match[] = { +- { .compatible = "qcom,sfpb-mutex" }, +- { .compatible = "qcom,tcsr-mutex" }, ++ { .compatible = "qcom,sfpb-mutex", .data = &of_sfpb_mutex }, ++ { .compatible = "qcom,tcsr-mutex", .data = &of_tcsr_mutex }, + { } + }; + MODULE_DEVICE_TABLE(of, qcom_hwspinlock_of_match); +@@ -112,12 +128,14 @@ static const struct regmap_config tcsr_m + static struct regmap *qcom_hwspinlock_probe_mmio(struct platform_device *pdev, + u32 *offset, u32 *stride) + { ++ const struct qcom_hwspinlock_of_data *data; + struct device *dev = &pdev->dev; + void __iomem *base; + +- /* All modern platform has offset 0 and stride of 4k */ +- *offset = 0; +- *stride = 0x1000; ++ data = of_device_get_match_data(dev); ++ ++ *offset = data->offset; ++ *stride = data->stride; + + base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(base)) diff --git a/target/linux/ipq806x/patches-5.15/105-v6.0-02-ARM-dts-qcom-ipq8064-add-missing-hwlock.patch b/target/linux/ipq806x/patches-5.15/105-v6.0-02-ARM-dts-qcom-ipq8064-add-missing-hwlock.patch new file mode 100644 index 0000000000..d8303442f7 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/105-v6.0-02-ARM-dts-qcom-ipq8064-add-missing-hwlock.patch @@ -0,0 +1,31 @@ +From fbe4be367b2169602f6a5949a20d2917b25714d4 Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 7 Jul 2022 12:20:39 +0200 +Subject: [PATCH 1/2] ARM: dts: qcom: ipq8064: add missing hwlock + +Add missing hwlock for ipq8064 dtsi provided by qcom,sfpb-mutex. + +Signed-off-by: Christian Marangi +Acked-by: Krzysztof Kozlowski +[bjorn: Moved the node inside /soc] +Signed-off-by: Bjorn Andersson +Link: https://lore.kernel.org/r/20220707102040.1859-2-ansuelsmth@gmail.com +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 7 +++++++ + 1 file changed, 7 insertions(+) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -1357,5 +1357,12 @@ + dma-names = "tx", "rx"; + }; + }; ++ ++ sfpb_mutex: hwlock@1200600 { ++ compatible = "qcom,sfpb-mutex"; ++ reg = <0x01200600 0x100>; ++ ++ #hwlock-cells = <1>; ++ }; + }; + }; diff --git a/target/linux/ipq806x/patches-5.15/105-v6.0-03-ARM-dts-qcom-ipq8064-add-missing-smem-compatible.patch b/target/linux/ipq806x/patches-5.15/105-v6.0-03-ARM-dts-qcom-ipq8064-add-missing-smem-compatible.patch new file mode 100644 index 0000000000..8b91eeb511 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/105-v6.0-03-ARM-dts-qcom-ipq8064-add-missing-smem-compatible.patch @@ -0,0 +1,30 @@ +From 4fefb5434c4b735daf913abaef12431405368031 Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 7 Jul 2022 12:20:40 +0200 +Subject: [PATCH 2/2] ARM: dts: qcom: ipq8064: add missing smem compatible + +Add missing smem compatible and hwlocks phandle for ipq8064 dtsi +smem node. + +Signed-off-by: Christian Marangi +Acked-by: Krzysztof Kozlowski +Signed-off-by: Bjorn Andersson +Link: https://lore.kernel.org/r/20220707102040.1859-3-ansuelsmth@gmail.com +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -292,8 +292,11 @@ + }; + + smem: smem@41000000 { ++ compatible = "qcom,smem"; + reg = <0x41000000 0x200000>; + no-map; ++ ++ hwlocks = <&sfpb_mutex 3>; + }; + }; + diff --git a/target/linux/ipq806x/patches-5.15/106-01-ARM-dts-qcom-ipq8064-add-v2-dtsi-variant.patch b/target/linux/ipq806x/patches-5.15/106-01-ARM-dts-qcom-ipq8064-add-v2-dtsi-variant.patch new file mode 100644 index 0000000000..8b20a550f6 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/106-01-ARM-dts-qcom-ipq8064-add-v2-dtsi-variant.patch @@ -0,0 +1,129 @@ +From 9f7097a8b1948533a6db1b53b5c0480cc75bbd16 Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Mon, 18 Jul 2022 18:05:16 +0200 +Subject: [PATCH 1/3] ARM: dts: qcom: ipq8064: add v2 dtsi variant + +Add ipq8064-v2.0 dtsi variant that differ from original ipq8064 SoC for +some additional pcie, sata and usb configuration values, additional +reserved memory and serial output. + +Signed-off-by: Christian Marangi +--- + .../boot/dts/qcom-ipq8064-v2.0-smb208.dtsi | 37 ++++++++++ + arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi | 69 +++++++++++++++++++ + 2 files changed, 106 insertions(+) + create mode 100644 arch/arm/boot/dts/qcom-ipq8064-v2.0-smb208.dtsi + create mode 100644 arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi + +--- /dev/null ++++ b/arch/arm/boot/dts/qcom-ipq8064-v2.0-smb208.dtsi +@@ -0,0 +1,37 @@ ++// SPDX-License-Identifier: GPL-2.0 ++ ++#include "qcom-ipq8064-v2.0.dtsi" ++ ++&rpm { ++ smb208_regulators: regulators { ++ compatible = "qcom,rpm-smb208-regulators"; ++ ++ smb208_s1a: s1a { ++ regulator-min-microvolt = <1050000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s1b: s1b { ++ regulator-min-microvolt = <1050000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s2a: s2a { ++ regulator-min-microvolt = < 800000>; ++ regulator-max-microvolt = <1250000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s2b: s2b { ++ regulator-min-microvolt = < 800000>; ++ regulator-max-microvolt = <1250000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi +@@ -0,0 +1,69 @@ ++// SPDX-License-Identifier: GPL-2.0 ++ ++#include "qcom-ipq8064.dtsi" ++ ++/ { ++ model = "Qualcomm Technologies, Inc. IPQ8064-v2.0"; ++ ++ aliases { ++ serial0 = &gsbi4_serial; ++ }; ++ ++ chosen { ++ stdout-path = "serial0:115200n8"; ++ }; ++ ++ reserved-memory { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ranges; ++ ++ rsvd@41200000 { ++ reg = <0x41200000 0x300000>; ++ no-map; ++ }; ++ }; ++}; ++ ++&gsbi4 { ++ qcom,mode = ; ++ status = "okay"; ++ ++ serial@16340000 { ++ status = "okay"; ++ }; ++ /* ++ * The i2c device on gsbi4 should not be enabled. ++ * On ipq806x designs gsbi4 i2c is meant for exclusive ++ * RPM usage. Turning this on in kernel manifests as ++ * i2c failure for the RPM. ++ */ ++}; ++ ++&pcie0 { ++ compatible = "qcom,pcie-ipq8064-v2"; ++}; ++ ++&pcie1 { ++ compatible = "qcom,pcie-ipq8064-v2"; ++}; ++ ++&pcie2 { ++ compatible = "qcom,pcie-ipq8064-v2"; ++}; ++ ++&sata { ++ ports-implemented = <0x1>; ++}; ++ ++&ss_phy_0 { ++ qcom,rx-eq = <2>; ++ qcom,tx-deamp_3_5db = <32>; ++ qcom,mpll = <5>; ++}; ++ ++&ss_phy_1 { ++ qcom,rx-eq = <2>; ++ qcom,tx-deamp_3_5db = <32>; ++ qcom,mpll = <5>; ++}; diff --git a/target/linux/ipq806x/patches-5.15/106-02-ARM-dts-qcom-ipq8064-add-ipq8062-variant.patch b/target/linux/ipq806x/patches-5.15/106-02-ARM-dts-qcom-ipq8064-add-ipq8062-variant.patch new file mode 100644 index 0000000000..fdff292480 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/106-02-ARM-dts-qcom-ipq8064-add-ipq8062-variant.patch @@ -0,0 +1,67 @@ +From 41d9fa8de7845bd92d9c963196fdfd7ea9232bb2 Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Mon, 18 Jul 2022 18:07:26 +0200 +Subject: [PATCH 2/3] ARM: dts: qcom: ipq8064: add ipq8062 variant + +ipq8062 SoC is based on ipq8064-v2.0 with lower supported freq, lack of +usb port and a reduced voltage output with the smb208 regulators. + +Signed-off-by: Christian Marangi +--- + arch/arm/boot/dts/qcom-ipq8062-smb208.dtsi | 37 ++++++++++++++++++++++ + arch/arm/boot/dts/qcom-ipq8062.dtsi | 8 +++++ + 2 files changed, 45 insertions(+) + create mode 100644 arch/arm/boot/dts/qcom-ipq8062-smb208.dtsi + create mode 100644 arch/arm/boot/dts/qcom-ipq8062.dtsi + +--- /dev/null ++++ b/arch/arm/boot/dts/qcom-ipq8062-smb208.dtsi +@@ -0,0 +1,37 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++ ++#include "qcom-ipq8062.dtsi" ++ ++&rpm { ++ smb208_regulators: regulators { ++ compatible = "qcom,rpm-smb208-regulators"; ++ ++ smb208_s1a: s1a { ++ regulator-min-microvolt = <1050000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s1b: s1b { ++ regulator-min-microvolt = <1050000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s2a: s2a { ++ regulator-min-microvolt = < 800000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s2b: s2b { ++ regulator-min-microvolt = < 800000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/qcom-ipq8062.dtsi +@@ -0,0 +1,8 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++ ++#include "qcom-ipq8064-v2.0.dtsi" ++ ++/ { ++ model = "Qualcomm Technologies, Inc. IPQ8062"; ++ compatible = "qcom,ipq8062", "qcom,ipq8064"; ++}; diff --git a/target/linux/ipq806x/patches-5.15/106-03-ARM-dts-qcom-ipq8064-add-ipq8065-variant.patch b/target/linux/ipq806x/patches-5.15/106-03-ARM-dts-qcom-ipq8064-add-ipq8065-variant.patch new file mode 100644 index 0000000000..bccc577b91 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/106-03-ARM-dts-qcom-ipq8064-add-ipq8065-variant.patch @@ -0,0 +1,67 @@ +From 01e7aa3fe6f76f7960f2382038136235eee9c6cd Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Mon, 18 Jul 2022 18:09:35 +0200 +Subject: [PATCH 3/3] ARM: dts: qcom: ipq8064: add ipq8065 variant + +ipq8065 SoC is based on ipq8064-v2.0 with a more clocked CPU and +an increased voltage output with the smb208 regulators. + +Signed-off-by: Christian Marangi +--- + arch/arm/boot/dts/qcom-ipq8065-smb208.dtsi | 37 ++++++++++++++++++++++ + arch/arm/boot/dts/qcom-ipq8065.dtsi | 8 +++++ + 2 files changed, 45 insertions(+) + create mode 100644 arch/arm/boot/dts/qcom-ipq8065-smb208.dtsi + create mode 100644 arch/arm/boot/dts/qcom-ipq8065.dtsi + +--- /dev/null ++++ b/arch/arm/boot/dts/qcom-ipq8065-smb208.dtsi +@@ -0,0 +1,37 @@ ++// SPDX-License-Identifier: GPL-2.0 ++ ++#include "qcom-ipq8065.dtsi" ++ ++&rpm { ++ smb208_regulators: regulators { ++ compatible = "qcom,rpm-smb208-regulators"; ++ ++ smb208_s1a: s1a { ++ regulator-min-microvolt = <1050000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s1b: s1b { ++ regulator-min-microvolt = <1050000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s2a: s2a { ++ regulator-min-microvolt = <775000>; ++ regulator-max-microvolt = <1275000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s2b: s2b { ++ regulator-min-microvolt = <775000>; ++ regulator-max-microvolt = <1275000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/qcom-ipq8065.dtsi +@@ -0,0 +1,8 @@ ++// SPDX-License-Identifier: GPL-2.0 ++ ++#include "qcom-ipq8064-v2.0.dtsi" ++ ++/ { ++ model = "Qualcomm Technologies, Inc. IPQ8065"; ++ compatible = "qcom,ipq8065", "qcom,ipq8064"; ++}; diff --git a/target/linux/ipq806x/patches-5.15/107-10-ARM-dts-qcom-add-saw-for-l2-cache-and-kraitcc-for.patch b/target/linux/ipq806x/patches-5.15/107-10-ARM-dts-qcom-add-saw-for-l2-cache-and-kraitcc-for.patch new file mode 100644 index 0000000000..12e4874f6b --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/107-10-ARM-dts-qcom-add-saw-for-l2-cache-and-kraitcc-for.patch @@ -0,0 +1,95 @@ +From bef5018abb7cf94efafdc05087b4c998891ae4ec Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Mon, 17 Jan 2022 23:39:34 +0100 +Subject: [PATCH v3 10/18] ARM: dts: qcom: add saw for l2 cache and kraitcc for + ipq8064 + +Add saw compatible for l2 cache and kraitcc node for ipq8064 dtsi. +Also declare clock-output-names for acc0 and acc1 and qsb fixed clock +for the secondary mux. + +Signed-off-by: Ansuel Smith +Tested-by: Jonathan McDowell +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 34 +++++++++++++++++++++++++++-- + 1 file changed, 32 insertions(+), 2 deletions(-) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -301,6 +301,12 @@ + }; + + clocks { ++// qsb: qsb { ++// compatible = "fixed-clock"; ++// clock-frequency = <384000000>; ++// #clock-cells = <0>; ++// }; ++ + cxo_board: cxo_board { + compatible = "fixed-clock"; + #clock-cells = <0>; +@@ -503,11 +509,19 @@ + acc0: clock-controller@2088000 { + compatible = "qcom,kpss-acc-v1"; + reg = <0x02088000 0x1000>, <0x02008000 0x1000>; ++ clock-output-names = "acpu0_aux"; ++ clocks = <&gcc PLL8_VOTE>, <&pxo_board>; ++ clock-names = "pll8_vote", "pxo"; ++ #clock-cells = <0>; + }; + + acc1: clock-controller@2098000 { + compatible = "qcom,kpss-acc-v1"; + reg = <0x02098000 0x1000>, <0x02008000 0x1000>; ++ clock-output-names = "acpu1_aux"; ++ clocks = <&gcc PLL8_VOTE>, <&pxo_board>; ++ clock-names = "pll8_vote", "pxo"; ++ #clock-cells = <0>; + }; + + adm_dma: dma-controller@18300000 { +@@ -531,17 +545,23 @@ + }; + + saw0: regulator@2089000 { +- compatible = "qcom,saw2"; ++ compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon"; + reg = <0x02089000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + + saw1: regulator@2099000 { +- compatible = "qcom,saw2"; ++ compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon"; + reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + ++ saw_l2: regulator@02012000 { ++ compatible = "qcom,saw2", "syscon"; ++ reg = <0x02012000 0x1000>; ++ regulator; ++ }; ++ + gsbi1: gsbi@12440000 { + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x12440000 0x100>; +@@ -920,6 +940,17 @@ + clocks = <&gcc PLL8_VOTE>, <&pxo_board>; + clock-names = "pll8_vote", "pxo"; + clock-output-names = "acpu_l2_aux"; ++ #clock-cells = <0>; ++ }; ++ ++ kraitcc: clock-controller { ++ compatible = "qcom,krait-cc-v1"; ++ clocks = <&gcc PLL9>, <&gcc PLL10>, <&gcc PLL12>, ++ <&acc0>, <&acc1>, <&l2cc>; // <&qsb> ++ clock-names = "hfpll0", "hfpll1", "hfpll_l2", ++ "acpu0_aux", "acpu1_aux", "acpu_l2_aux"; ++// "qsb"; ++ #clock-cells = <1>; + }; + + lcc: clock-controller@28000000 { diff --git a/target/linux/ipq806x/patches-5.15/107-13-ARM-dts-qcom-add-opp-table-for-cpu-and-l2-for-ipq.patch b/target/linux/ipq806x/patches-5.15/107-13-ARM-dts-qcom-add-opp-table-for-cpu-and-l2-for-ipq.patch new file mode 100644 index 0000000000..f3c8f18f1d --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/107-13-ARM-dts-qcom-add-opp-table-for-cpu-and-l2-for-ipq.patch @@ -0,0 +1,268 @@ +From 076ebb6e1799c4c7a1d2e07510d88b9e9b57b551 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Tue, 18 Jan 2022 00:03:47 +0100 +Subject: [PATCH v3 13/18] ARM: dts: qcom: add opp table for cpu and l2 for + ipq8064 + +Add opp table for cpu and l2 cache. While the current cpufreq is +the generic one that doesn't scale the L2 cache, we add the l2 +cache opp anyway for the sake of completeness. This will be handy in the +future when a dedicated cpufreq driver is introduced for krait cores +that will correctly scale l2 cache with the core freq. + +Opp-level is set based on the logic of +0: idle level +1: normal level +2: turbo level + +Signed-off-by: Ansuel Smith +Tested-by: Jonathan McDowell +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 99 +++++++++++++++++++++++++++++ + 1 file changed, 99 insertions(+) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -48,6 +48,105 @@ + }; + }; + ++ opp_table_l2: opp_table_l2 { ++ compatible = "operating-points-v2"; ++ ++ opp-384000000 { ++ opp-hz = /bits/ 64 <384000000>; ++ opp-microvolt = <1100000>; ++ clock-latency-ns = <100000>; ++ opp-level = <0>; ++ }; ++ ++ opp-1000000000 { ++ opp-hz = /bits/ 64 <1000000000>; ++ opp-microvolt = <1100000>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ ++ opp-1200000000 { ++ opp-hz = /bits/ 64 <1200000000>; ++ opp-microvolt = <1150000>; ++ clock-latency-ns = <100000>; ++ opp-level = <2>; ++ }; ++ }; ++ ++ opp_table0: opp_table0 { ++ compatible = "operating-points-v2-kryo-cpu"; ++ nvmem-cells = <&speedbin_efuse>; ++ ++ /* ++ * Voltage thresholds are ++ */ ++ opp-384000000 { ++ opp-hz = /bits/ 64 <384000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; ++ opp-microvolt-speed0-pvs1-v0 = <925000 878750 971250>; ++ opp-microvolt-speed0-pvs2-v0 = <875000 831250 918750>; ++ opp-microvolt-speed0-pvs3-v0 = <800000 760000 840000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <0>; ++ }; ++ ++ opp-600000000 { ++ opp-hz = /bits/ 64 <600000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; ++ opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>; ++ opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>; ++ opp-microvolt-speed0-pvs3-v0 = <850000 807500 892500>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ ++ opp-800000000 { ++ opp-hz = /bits/ 64 <800000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; ++ opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; ++ opp-microvolt-speed0-pvs2-v0 = <995000 945250 1044750>; ++ opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ ++ opp-1000000000 { ++ opp-hz = /bits/ 64 <1000000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1150000 1092500 1207500>; ++ opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; ++ opp-microvolt-speed0-pvs2-v0 = <1025000 973750 1076250>; ++ opp-microvolt-speed0-pvs3-v0 = <950000 902500 997500>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ ++ opp-1200000000 { ++ opp-hz = /bits/ 64 <1200000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1200000 1140000 1260000>; ++ opp-microvolt-speed0-pvs1-v0 = <1125000 1068750 1181250>; ++ opp-microvolt-speed0-pvs2-v0 = <1075000 1021250 1128750>; ++ opp-microvolt-speed0-pvs3-v0 = <1000000 950000 1050000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <2>; ++ }; ++ ++ opp-1400000000 { ++ opp-hz = /bits/ 64 <1400000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1250000 1187500 1312500>; ++ opp-microvolt-speed0-pvs1-v0 = <1175000 1116250 1233750>; ++ opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>; ++ opp-microvolt-speed0-pvs3-v0 = <1050000 997500 1102500>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <2>; ++ }; ++ }; ++ + thermal-zones { + tsens_tz_sensor0 { + polling-delay-passive = <0>; +--- a/arch/arm/boot/dts/qcom-ipq8065.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8065.dtsi +@@ -6,3 +6,92 @@ + model = "Qualcomm Technologies, Inc. IPQ8065"; + compatible = "qcom,ipq8065", "qcom,ipq8064"; + }; ++ ++&opp_table_l2 { ++ /delete-node/opp-1200000000; ++ ++ opp-1400000000 { ++ opp-hz = /bits/ 64 <1400000000>; ++ opp-microvolt = <1150000>; ++ clock-latency-ns = <100000>; ++ opp-level = <2>; ++ }; ++}; ++ ++&opp_table0 { ++ /* ++ * On ipq8065 1.2 ghz freq is not present ++ * Remove it to make cpufreq work and not ++ * complain for missing definition ++ */ ++ ++ /delete-node/opp-1200000000; ++ ++ /* ++ * Voltage thresholds are ++ */ ++ opp-384000000 { ++ opp-microvolt-speed0-pvs0-v0 = <975000 926250 1023750>; ++ opp-microvolt-speed0-pvs1-v0 = <950000 902500 997500>; ++ opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>; ++ opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>; ++ opp-microvolt-speed0-pvs4-v0 = <875000 831250 918750>; ++ opp-microvolt-speed0-pvs5-v0 = <825000 783750 866250>; ++ opp-microvolt-speed0-pvs6-v0 = <775000 736250 813750>; ++ }; ++ ++ opp-600000000 { ++ opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; ++ opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>; ++ opp-microvolt-speed0-pvs2-v0 = <950000 902500 997500>; ++ opp-microvolt-speed0-pvs3-v0 = <925000 878750 971250>; ++ opp-microvolt-speed0-pvs4-v0 = <900000 855000 945000>; ++ opp-microvolt-speed0-pvs5-v0 = <850000 807500 892500>; ++ opp-microvolt-speed0-pvs6-v0 = <800000 760000 840000>; ++ }; ++ ++ opp-800000000 { ++ opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; ++ opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; ++ opp-microvolt-speed0-pvs2-v0 = <1000000 950000 1050000>; ++ opp-microvolt-speed0-pvs3-v0 = <975000 926250 1023750>; ++ opp-microvolt-speed0-pvs4-v0 = <950000 902500 997500>; ++ opp-microvolt-speed0-pvs5-v0 = <900000 855000 945000>; ++ opp-microvolt-speed0-pvs6-v0 = <850000 807500 892500>; ++ }; ++ ++ opp-1000000000 { ++ opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; ++ opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; ++ opp-microvolt-speed0-pvs2-v0 = <1050000 997500 1102500>; ++ opp-microvolt-speed0-pvs3-v0 = <1025000 973750 1076250>; ++ opp-microvolt-speed0-pvs4-v0 = <1000000 950000 1050000>; ++ opp-microvolt-speed0-pvs5-v0 = <950000 902500 997500>; ++ opp-microvolt-speed0-pvs6-v0 = <900000 855000 945000>; ++ }; ++ ++ opp-1400000000 { ++ opp-microvolt-speed0-pvs0-v0 = <1175000 1116250 1233750>; ++ opp-microvolt-speed0-pvs1-v0 = <1150000 1092500 1207500>; ++ opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>; ++ opp-microvolt-speed0-pvs3-v0 = <1100000 1045000 1155000>; ++ opp-microvolt-speed0-pvs4-v0 = <1075000 1021250 1128750>; ++ opp-microvolt-speed0-pvs5-v0 = <1025000 973750 1076250>; ++ opp-microvolt-speed0-pvs6-v0 = <975000 926250 1023750>; ++ opp-level = <1>; ++ }; ++ ++ opp-1725000000 { ++ opp-hz = /bits/ 64 <1725000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1262500 1199375 1325625>; ++ opp-microvolt-speed0-pvs1-v0 = <1225000 1163750 1286250>; ++ opp-microvolt-speed0-pvs2-v0 = <1200000 1140000 1260000>; ++ opp-microvolt-speed0-pvs3-v0 = <1175000 1116250 1233750>; ++ opp-microvolt-speed0-pvs4-v0 = <1150000 1092500 1207500>; ++ opp-microvolt-speed0-pvs5-v0 = <1100000 1045000 1155000>; ++ opp-microvolt-speed0-pvs6-v0 = <1050000 997500 1102500>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <2>; ++ }; ++}; +--- a/arch/arm/boot/dts/qcom-ipq8062.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8062.dtsi +@@ -6,3 +6,39 @@ + model = "Qualcomm Technologies, Inc. IPQ8062"; + compatible = "qcom,ipq8062", "qcom,ipq8064"; + }; ++ ++&opp_table0 { ++ /delete-node/opp-1200000000; ++ /delete-node/opp-1400000000; ++ ++ /* ++ * Voltage thresholds are ++ */ ++ opp-384000000 { ++ opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; ++ opp-microvolt-speed0-pvs1-v0 = < 925000 878750 971250>; ++ opp-microvolt-speed0-pvs2-v0 = < 875000 831250 918750>; ++ opp-microvolt-speed0-pvs3-v0 = < 800000 760000 840000>; ++ }; ++ ++ opp-600000000 { ++ opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; ++ opp-microvolt-speed0-pvs1-v0 = < 975000 926250 1023750>; ++ opp-microvolt-speed0-pvs2-v0 = < 925000 878750 971250>; ++ opp-microvolt-speed0-pvs3-v0 = < 850000 807500 892500>; ++ }; ++ ++ opp-800000000 { ++ opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; ++ opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; ++ opp-microvolt-speed0-pvs2-v0 = < 995000 945250 1044750>; ++ opp-microvolt-speed0-pvs3-v0 = < 900000 855000 945000>; ++ }; ++ ++ opp-1000000000 { ++ opp-microvolt-speed0-pvs0-v0 = <1150000 1092500 1207500>; ++ opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; ++ opp-microvolt-speed0-pvs2-v0 = <1025000 973750 1076250>; ++ opp-microvolt-speed0-pvs3-v0 = < 950000 902500 997500>; ++ }; ++}; diff --git a/target/linux/ipq806x/patches-5.15/107-15-ARM-dts-qcom-add-multiple-missing-binding-for-cpu.patch b/target/linux/ipq806x/patches-5.15/107-15-ARM-dts-qcom-add-multiple-missing-binding-for-cpu.patch new file mode 100644 index 0000000000..cf27aaa08b --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/107-15-ARM-dts-qcom-add-multiple-missing-binding-for-cpu.patch @@ -0,0 +1,153 @@ +From 211fc0c0a63c99b68663a27182e643316c2d8cbe Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Tue, 18 Jan 2022 00:07:57 +0100 +Subject: [PATCH v3 15/18] ARM: dts: qcom: add multiple missing binding for cpu + and l2 for ipq8064 + +Add multiple binding for cpu node, l2 node and add idle-states +definition for ipq8064 dtsi. + +Signed-off-by: Ansuel Smith +Tested-by: Jonathan McDowell +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 36 +++++++++++++++++++++++++++++ + 1 file changed, 36 insertions(+) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -30,6 +30,15 @@ + next-level-cache = <&L2>; + qcom,acc = <&acc0>; + qcom,saw = <&saw0>; ++ clocks = <&kraitcc 0>, <&kraitcc 4>; ++ clock-names = "cpu", "l2"; ++ clock-latency = <100000>; ++ operating-points-v2 = <&opp_table0>; ++ voltage-tolerance = <5>; ++ cooling-min-state = <0>; ++ cooling-max-state = <10>; ++ #cooling-cells = <2>; ++ cpu-idle-states = <&CPU_SPC>; + }; + + cpu1: cpu@1 { +@@ -40,11 +49,35 @@ + next-level-cache = <&L2>; + qcom,acc = <&acc1>; + qcom,saw = <&saw1>; ++ clocks = <&kraitcc 1>, <&kraitcc 4>; ++ clock-names = "cpu", "l2"; ++ clock-latency = <100000>; ++ operating-points-v2 = <&opp_table0>; ++ voltage-tolerance = <5>; ++ cooling-min-state = <0>; ++ cooling-max-state = <10>; ++ #cooling-cells = <2>; ++ cpu-idle-states = <&CPU_SPC>; ++ }; ++ ++ idle-states { ++ CPU_SPC: spc { ++ compatible = "qcom,idle-state-spc"; ++ status = "disabled"; ++ entry-latency-us = <400>; ++ exit-latency-us = <900>; ++ min-residency-us = <3000>; ++ }; + }; + + L2: l2-cache { + compatible = "cache"; + cache-level = <2>; ++ qcom,saw = <&saw_l2>; ++ ++ clocks = <&kraitcc 4>; ++ clock-names = "l2"; ++ operating-points-v2 = <&opp_table_l2>; + }; + }; + +--- a/arch/arm/boot/dts/qcom-ipq8064-smb208.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064-smb208.dtsi +@@ -2,6 +2,18 @@ + + #include "qcom-ipq8064.dtsi" + ++&cpu0 { ++ cpu-supply = <&smb208_s2a>; ++}; ++ ++&cpu1 { ++ cpu-supply = <&smb208_s2b>; ++}; ++ ++&L2 { ++ l2-supply = <&smb208_s1a>; ++}; ++ + &rpm { + smb208_regulators: regulators { + compatible = "qcom,rpm-smb208-regulators"; +--- a/arch/arm/boot/dts/qcom-ipq8064-v2.0-smb208.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064-v2.0-smb208.dtsi +@@ -2,6 +2,18 @@ + + #include "qcom-ipq8064-v2.0.dtsi" + ++&cpu0 { ++ cpu-supply = <&smb208_s2a>; ++}; ++ ++&cpu1 { ++ cpu-supply = <&smb208_s2b>; ++}; ++ ++&L2 { ++ l2-supply = <&smb208_s1a>; ++}; ++ + &rpm { + smb208_regulators: regulators { + compatible = "qcom,rpm-smb208-regulators"; +--- a/arch/arm/boot/dts/qcom-ipq8062-smb208.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8062-smb208.dtsi +@@ -2,6 +2,18 @@ + + #include "qcom-ipq8062.dtsi" + ++&cpu0 { ++ cpu-supply = <&smb208_s2a>; ++}; ++ ++&cpu1 { ++ cpu-supply = <&smb208_s2b>; ++}; ++ ++&L2 { ++ l2-supply = <&smb208_s1a>; ++}; ++ + &rpm { + smb208_regulators: regulators { + compatible = "qcom,rpm-smb208-regulators"; +--- a/arch/arm/boot/dts/qcom-ipq8065-smb208.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8065-smb208.dtsi +@@ -2,6 +2,18 @@ + + #include "qcom-ipq8065.dtsi" + ++&cpu0 { ++ cpu-supply = <&smb208_s2a>; ++}; ++ ++&cpu1 { ++ cpu-supply = <&smb208_s2b>; ++}; ++ ++&L2 { ++ l2-supply = <&smb208_s1a>; ++}; ++ + &rpm { + smb208_regulators: regulators { + compatible = "qcom,rpm-smb208-regulators"; diff --git a/target/linux/ipq806x/patches-5.15/108-01-ARM-dts-qcom-fix-wrong-nad_pins-definition-for-ipq80.patch b/target/linux/ipq806x/patches-5.15/108-01-ARM-dts-qcom-fix-wrong-nad_pins-definition-for-ipq80.patch new file mode 100644 index 0000000000..d3f821a6a0 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/108-01-ARM-dts-qcom-fix-wrong-nad_pins-definition-for-ipq80.patch @@ -0,0 +1,29 @@ +From 6c94e0184e56f9e9f1f5d5f54b20758433e498d2 Mon Sep 17 00:00:00 2001 +From: Christian 'Ansuel' Marangi +Date: Wed, 15 Jun 2022 16:47:09 +0200 +Subject: [PATCH 1/2] ARM: dts: qcom: fix wrong nad_pins definition for ipq806x + +Fix wrong nand_pings definition for bias-disable pins. + +Signed-off-by: Christian 'Ansuel' Marangi +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 7 ++----- + 1 file changed, 2 insertions(+), 5 deletions(-) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -559,12 +559,9 @@ + }; + + nand_pins: nand_pins { +- mux { ++ disable { + pins = "gpio34", "gpio35", "gpio36", +- "gpio37", "gpio38", "gpio39", +- "gpio40", "gpio41", "gpio42", +- "gpio43", "gpio44", "gpio45", +- "gpio46", "gpio47"; ++ "gpio37", "gpio38"; + function = "nand"; + drive-strength = <10>; + bias-disable; diff --git a/target/linux/ipq806x/patches-5.15/108-02-ARM-dts-qcom-add-MDIO-dedicated-controller-node-for-.patch b/target/linux/ipq806x/patches-5.15/108-02-ARM-dts-qcom-add-MDIO-dedicated-controller-node-for-.patch new file mode 100644 index 0000000000..4a57fc0330 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/108-02-ARM-dts-qcom-add-MDIO-dedicated-controller-node-for-.patch @@ -0,0 +1,188 @@ +From 504188183408fac0f61b59f5ed8ea1773fe43669 Mon Sep 17 00:00:00 2001 +From: Christian 'Ansuel' Marangi +Date: Wed, 15 Jun 2022 16:59:30 +0200 +Subject: [PATCH 2/2] ARM: dts: qcom: add MDIO dedicated controller node for + ipq806x + +Add MDIO dedicated controller attached to gmac0 and fix rb3011 dts to +correctly use the new tag. + +Signed-off-by: Christian 'Ansuel' Marangi +--- + arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 134 +++++++++++----------- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 14 +++ + 2 files changed, 81 insertions(+), 67 deletions(-) + +--- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts ++++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts +@@ -24,73 +24,6 @@ + device_type = "memory"; + }; + +- mdio0: mdio-0 { +- status = "okay"; +- compatible = "virtual,mdio-gpio"; +- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, +- <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; +- #address-cells = <1>; +- #size-cells = <0>; +- +- pinctrl-0 = <&mdio0_pins>; +- pinctrl-names = "default"; +- +- switch0: switch@10 { +- compatible = "qca,qca8337"; +- #address-cells = <1>; +- #size-cells = <0>; +- +- dsa,member = <0 0>; +- +- pinctrl-0 = <&sw0_reset_pin>; +- pinctrl-names = "default"; +- +- reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; +- reg = <0x10>; +- +- ports { +- #address-cells = <1>; +- #size-cells = <0>; +- +- switch0cpu: port@0 { +- reg = <0>; +- label = "cpu"; +- ethernet = <&gmac0>; +- phy-mode = "rgmii-id"; +- fixed-link { +- speed = <1000>; +- full-duplex; +- }; +- }; +- +- port@1 { +- reg = <1>; +- label = "sw1"; +- }; +- +- port@2 { +- reg = <2>; +- label = "sw2"; +- }; +- +- port@3 { +- reg = <3>; +- label = "sw3"; +- }; +- +- port@4 { +- reg = <4>; +- label = "sw4"; +- }; +- +- port@5 { +- reg = <5>; +- label = "sw5"; +- }; +- }; +- }; +- }; +- + mdio1: mdio-1 { + status = "okay"; + compatible = "virtual,mdio-gpio"; +@@ -220,6 +153,73 @@ + status = "okay"; + }; + ++&mdio0 { ++ status = "okay"; ++ compatible = "virtual,mdio-gpio"; ++ gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, ++ <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pinctrl-0 = <&mdio0_pins>; ++ pinctrl-names = "default"; ++ ++ switch0: switch@10 { ++ compatible = "qca,qca8337"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ dsa,member = <0 0>; ++ ++ pinctrl-0 = <&sw0_reset_pin>; ++ pinctrl-names = "default"; ++ ++ reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; ++ reg = <0x10>; ++ ++ ports { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ switch0cpu: port@0 { ++ reg = <0>; ++ label = "cpu"; ++ ethernet = <&gmac0>; ++ phy-mode = "rgmii-id"; ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ ++ port@1 { ++ reg = <1>; ++ label = "sw1"; ++ }; ++ ++ port@2 { ++ reg = <2>; ++ label = "sw2"; ++ }; ++ ++ port@3 { ++ reg = <3>; ++ label = "sw3"; ++ }; ++ ++ port@4 { ++ reg = <4>; ++ label = "sw4"; ++ }; ++ ++ port@5 { ++ reg = <5>; ++ label = "sw5"; ++ }; ++ }; ++ }; ++}; ++ + &gmac0 { + status = "okay"; + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -1446,6 +1446,20 @@ + }; + }; + ++ mdio0: mdio@37000000 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ compatible = "qcom,ipq8064-mdio", "syscon"; ++ reg = <0x37000000 0x200000>; ++ resets = <&gcc GMAC_CORE1_RESET>; ++ reset-names = "stmmaceth"; ++ clocks = <&gcc GMAC_CORE1_CLK>; ++ clock-names = "stmmaceth"; ++ ++ status = "disabled"; ++ }; ++ + vsdcc_fixed: vsdcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "SDCC Power"; diff --git a/target/linux/ipq806x/patches-5.15/851-add-gsbi1-dts.patch b/target/linux/ipq806x/patches-5.15/851-add-gsbi1-dts.patch deleted file mode 100644 index b7c198c126..0000000000 --- a/target/linux/ipq806x/patches-5.15/851-add-gsbi1-dts.patch +++ /dev/null @@ -1,44 +0,0 @@ ---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi -@@ -689,6 +689,41 @@ - reg = <0x12100000 0x10000>; - }; - -+ gsbi1: gsbi@12440000 { -+ compatible = "qcom,gsbi-v1.0.0"; -+ cell-index = <1>; -+ reg = <0x12440000 0x100>; -+ clocks = <&gcc GSBI1_H_CLK>; -+ clock-names = "iface"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ ranges; -+ status = "disabled"; -+ -+ syscon-tcsr = <&tcsr>; -+ -+ gsbi1_serial: serial@12450000 { -+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; -+ reg = <0x12450000 0x100>, -+ <0x12400000 0x03>; -+ interrupts = ; -+ clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>; -+ clock-names = "core", "iface"; -+ status = "disabled"; -+ }; -+ -+ gsbi1_i2c: i2c@12460000 { -+ compatible = "qcom,i2c-qup-v1.1.1"; -+ reg = <0x12460000 0x1000>; -+ interrupts = ; -+ clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; -+ clock-names = "core", "iface"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "disabled"; -+ }; -+ }; -+ - gsbi2: gsbi@12480000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <2>;