From: Chukun Pan Date: Wed, 3 May 2023 15:18:48 +0000 (+0800) Subject: ipq40xx: add support for YYeTs LE1 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=9889de3397acc0b0ca4d1f0d42a8f7321c7f5ba0;p=openwrt%2Fstaging%2Fblocktrron.git ipq40xx: add support for YYeTs LE1 Hardware Highlights: SoC: Qualcomm IPQ4019 717 MHz RAM: 512M NT5CC256M16ER-EK Flash: 32M SPI NOR MX25L25635F WIFI1: 2.4 GHz 2T2R integrated WIFI2: 5 GHz 2T2R integrated Ethernet: QCA8075 (4x LAN, 1x WAN) LEDS: power, wlan2g, wlan5g, usb USB: 1x 3.0 Button: Reset Installation: Upload factory.bin in stock firmware's upgrade page, and this will take a few minutes. Signed-off-by: Chukun Pan --- diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 614afa8590..5353cd398d 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -25,6 +25,7 @@ ipq40xx_setup_interfaces() p2w,r619ac-128m|\ pakedge,wr-1|\ teltonika,rutx50|\ + yyets,le1|\ zyxel,nbg6617) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan" ;; diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-le1.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-le1.dts new file mode 100644 index 0000000000..282a0eaaa6 --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-le1.dts @@ -0,0 +1,326 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "YYeTs LE1"; + compatible = "yyets,le1"; + + aliases { + led-boot = &led_usb; + led-failsafe = &led_usb; + led-upgrade = &led_usb; + + ethernet0 = &swport5; + ethernet1 = &gmac; + label-mac-device = &gmac; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_usb: usb { + label = "green:usb"; + gpios = <&tlmm 36 GPIO_ACTIVE_LOW>; + linux,default-trigger = "usbport"; + trigger-sources = <&usb3_port1>, <&usb3_port2>, <&usb2_port1>; + }; + + wlan2g { + label = "green:wlan2g"; + gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "green:wlan5g"; + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + }; + + soc { + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + label = "QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + + partition@c0000 { + label = "CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + + partition@d0000 { + label = "DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + + partition@e0000 { + label = "APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + + partition@f0000 { + label = "APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + + partition@170000 { + label = "ART"; + reg = <0x170000 0x10000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + precal_art_1000: precal@1000 { + reg = <0x1000 0x2f20>; + }; + + precal_art_5000: precal@5000 { + reg = <0x5000 0x2f20>; + }; + }; + + partition@180000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x180000 0x1e80000>; + }; + }; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&gmac { + status = "okay"; +}; + +&mdio { + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&switch { + status = "okay"; +}; + +&swport1 { + status = "okay"; +}; + +&swport2 { + status = "okay"; +}; + +&swport3 { + status = "okay"; +}; + +&swport4 { + status = "okay"; +}; + +&swport5 { + status = "okay"; +}; + +&tlmm { + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&usb2 { + status = "okay"; + + dwc3@6000000 { + #address-cells = <1>; + #size-cells = <0>; + + usb2_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3 { + status = "okay"; + + dwc3@8a00000 { + #address-cells = <1>; + #size-cells = <0>; + + usb3_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + usb3_port2: port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + }; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + nvmem-cells = <&precal_art_1000>; + nvmem-cell-names = "pre-calibration"; + qcom,ath10k-calibration-variant = "YYeTs-LE1"; +}; + +&wifi1 { + status = "okay"; + nvmem-cells = <&precal_art_5000>; + nvmem-cell-names = "pre-calibration"; + qcom,ath10k-calibration-variant = "YYeTs-LE1"; +}; diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk index 8fd7ab2915..6dd4549f8d 100644 --- a/target/linux/ipq40xx/image/generic.mk +++ b/target/linux/ipq40xx/image/generic.mk @@ -1122,6 +1122,20 @@ define Device/wallys_dr40x9 endef TARGET_DEVICES += wallys_dr40x9 +define Device/yyets_le1 + $(call Device/FitzImage) + DEVICE_VENDOR := YYeTs + DEVICE_MODEL := LE1 + SOC := qcom-ipq4019 + KERNEL_SIZE := 4096k + IMAGE_SIZE := 31232k + IMAGES += factory.bin + IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata + DEVICE_PACKAGES := ipq-wifi-yyets_le1 kmod-usb-ledtrig-usbport +endef +TARGET_DEVICES += yyets_le1 + define Device/zte_mf18a $(call Device/FitImage) DEVICE_VENDOR := ZTE