From: Juan Pedro Paredes Caballero Date: Sat, 7 Dec 2024 13:20:31 +0000 (+0100) Subject: mediatek: filogic: Add support for cudy wr3000h X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=9d66b8b312fb6a4087244ee3ee10e1ba1623df81;p=openwrt%2Fopenwrt.git mediatek: filogic: Add support for cudy wr3000h The manufacturer Cudy usually releases signed openwrt firmware, to facilitate the migration from the proprietary version to the official versions of openwrt. In contact with the manufacturer tells me that only releases the firmware of the WR3000H if and only if there is an official version. With this proposal I pretend to have an initial operative version so that they do their part, and facilitate to the users the possibility of using openwrt. In the present state, it is only possible to use this firmware by uploading and installing it with UART connection. AX3000 2.5G Dual Band Wi-Fi 6 Mesh Router (WR3000H) Hardware -------- MediaTek MT7981 WiSoC 256MB DDR3 RAM 128MB SPI-NAND (XMC XM25QH128C) MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5) 4 LAN MediaTek MT7531 PHY 1 WAN RTL8221B-VB-CG 2.5Gbps PHY (C22) 2 Radios MT7976CN UART: 115200 8N1 3.3V MAC: LAN MAC: label mac WAN MAC: label mac + 1 2.4G MAC: label mac 5G MAC: label mac + 1 with LA bit set Installation ------------ 1. Connect to the serial port as described in the "Hardware" section. 2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell (The recovery.bin image load process must fail). 3. Download the OpenWrt initramfs image. Place it on an TFTP server connected to the Cudy LAN ports. Make sure the server is reachable at 192.168.1.88. Rename the image to "cudy3000h.bin" 4. Download and boot the OpenWrt initramfs image. $ tftpboot 0x46000000 cudy3000h.bin; bootm 0x46000000 5. IMPORTANT: Make backup from original firmware. System -> Backup /Flash Firmware -> Save mtdblock contents. All mtdblock one by one, keep unaltered (BL2, u-boot-env, Factory, bdinfo, FIP, and ubi). 6. Transfer the OpenWrt sysupgrade image to the device using scp. Install with sysupgrade. Warning for BL2 and U-BOOT developers ------------------------------------- The nand partition layout from vendor is slightly diferent from "standard". The FIP partition starts at 0x3c0000 be carefull with BL2 to BL31. The UBI partition start at 0x5c0000 be carefull. DO NOT OVERWRITE bdinfo partition it contains hardware MAC definition Layout is start-end (not start size) - 0x000000000000-0x000007800000 : "nmbm0" - 0x000000000000-0x000000100000 : "bl2" - 0x000000100000-0x000000180000 : "u-boot-env" - 0x000000180000-0x000000380000 : "factory" - 0x000000380000-0x0000003c0000 : "bdinfo" - 0x0000003c0000-0x0000005c0000 : "fip" - 0x0000005c0000-0x0000045c0000 : "ubi" ALLWAYS for U-BOOT operations check this setenv mtdids nmbm0=nmbm0 setenv mtdparts nmbm0:1024k(bl2),512k(u-boot-env),2048k(factory),256k(bdinfo),2048k(fip),65536k(ubi) Signed-off-by: Juan Pedro Paredes Caballero Link: https://github.com/openwrt/openwrt/pull/17458 Signed-off-by: Hauke Mehrtens --- diff --git a/target/linux/mediatek/dts/mt7981b-cudy-wr3000h-v1.dts b/target/linux/mediatek/dts/mt7981b-cudy-wr3000h-v1.dts new file mode 100644 index 0000000000..0808eb9557 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-cudy-wr3000h-v1.dts @@ -0,0 +1,337 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include + +#include "mt7981.dtsi" + +/ { + model = "Cudy WR3000H v1"; + compatible = "cudy,wr3000h-v1", "mediatek,mt7981-spim-snand-rfb"; + + aliases { + label-mac-device = &gmac0; + led-boot = &led_status; + led-failsafe = &led_status; + led-running = &led_status; + led-upgrade = &led_status; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "wps"; + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-export { + compatible = "gpio-export"; + #size-cells = <0>; + + phyreset { + gpio-export,name = "phyreset"; + gpio-export,output = <1>; + gpios = <&pio 3 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status: led@0 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&pio 5 GPIO_ACTIVE_LOW>; + }; + + + led_internet { + function = LED_FUNCTION_WAN_ONLINE; + color = ; + gpios = <&pio 11 GPIO_ACTIVE_LOW>; + }; + + led_wps { + function = LED_FUNCTION_WPS; + color = ; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + led_wlan2g { + function = LED_FUNCTION_WLAN_2GHZ; + color = ; + gpios = <&pio 6 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led_wlan5g { + function = LED_FUNCTION_WLAN_5GHZ; + color = ; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + led_lan1 { + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + color = ; + gpios = <&pio 8 GPIO_ACTIVE_LOW>; + }; + + led_lan2 { + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + color = ; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + + led_lan3 { + function = LED_FUNCTION_LAN; + function-enumerator = <3>; + color = ; + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + }; + + led_lan4 { + function = LED_FUNCTION_LAN; + function-enumerator = <4>; + color = ; + gpios = <&pio 13 GPIO_ACTIVE_LOW>; + }; + + led_wan { + function = LED_FUNCTION_WAN; + color = ; + gpios = <&pio 35 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_bdinfo_de00 0>; + label = "lan"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "2500base-x"; + phy-handle = <&phy6>; + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_bdinfo_de00 1>; + label = "wan"; + }; + +}; + +&mdio_bus { + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + }; + phy6: ethernet-phy@6 { + compatible = "ethernet-phy-ieee802.3-c22"; // [RTL8221B-VB-CG 2.5Gbps PHY (C22)] + reg = <6>; + phy-mode = "2500base-x"; + }; + +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <0>; + spi-max-frequency = <52000000>; + + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>; + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x00000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + read-only; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x0200000>; + read-only; + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + }; + }; + + partition@380000 { + label = "bdinfo"; + reg = <0x380000 0x0040000>; + read-only; + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_bdinfo_de00: macaddr@de00 { + compatible = "mac-base"; + reg = <0xde00 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@3C0000 { + label = "FIP"; + reg = <0x3C0000 0x0200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x5C0000 0x4000000>; + compatible = "linux,ubi"; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = ; + bias-pull-up = ; + }; + + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = ; + bias-pull-down = ; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&wifi { + status = "okay"; + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index ca4961c655..a6bb9b0ca8 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -38,6 +38,14 @@ cudy,re3000-v1) cudy,wr3000-v1) ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" ;; +cudy,wr3000h-v1) + ucidef_set_led_netdev "lan1" "lan1" "white:lan-1" "lan1" "link tx rx" + ucidef_set_led_netdev "lan2" "lan2" "white:lan-2" "lan2" "link tx rx" + ucidef_set_led_netdev "lan3" "lan3" "white:lan-3" "lan3" "link tx rx" + ucidef_set_led_netdev "lan4" "lan4" "white:lan-4" "lan4" "link tx rx" + ucidef_set_led_netdev "wan" "wan" "white:wan" "wan" "link tx rx" + ucidef_set_led_netdev "internet" "internet" "white:wan-online" "wan" "link" + ;; glinet,gl-x3000|\ glinet,gl-xe3000) ucidef_set_led_default "power" "POWER" "green:power" "1" diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 3188fe71d5..4ae2c70658 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -79,6 +79,7 @@ case "$board" in cudy,re3000-v1|\ cudy,tr3000-v1|\ cudy,wr3000s-v1|\ + cudy,wr3000h-v1|\ cudy,wr3000-v1) addr=$(mtd_get_mac_binary bdinfo 0xde00) # Originally, phy0 is phy1 mac with LA bit set. However, this would conflict diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index 7556be52bd..1d89640a4e 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -118,6 +118,10 @@ platform_do_upgrade() { CI_KERNPART="linux" nand_do_upgrade "$1" ;; + cudy,wr3000h-v1) + CI_UBIPART="ubi" + nand_do_upgrade "$1" + ;; cudy,re3000-v1|\ cudy,wr3000-v1|\ yuncore,ax835) diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 22c9151ff3..afa5224b19 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -705,6 +705,23 @@ define Device/cudy_wr3000s-v1 endef TARGET_DEVICES += cudy_wr3000s-v1 +define Device/cudy_wr3000h-v1 + DEVICE_VENDOR := Cudy + DEVICE_MODEL := WR3000H + DEVICE_VARIANT := v1 + DEVICE_DTS := mt7981b-cudy-wr3000h-v1 + DEVICE_DTS_DIR := ../dts + SUPPORTED_DEVICES += R59 + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 65536k + KERNEL_IN_UBI := 1 + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware +endef +TARGET_DEVICES += cudy_wr3000h-v1 + define Device/dlink_aquila-pro-ai-m30-a1 DEVICE_VENDOR := D-Link DEVICE_MODEL := AQUILA PRO AI M30