From: Sven Eckelmann Date: Mon, 23 Nov 2020 12:41:34 +0000 (+0100) Subject: ath79: add support for OpenMesh OM2P-HS v1 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=a462412977cc25b79a7a3479527e754d85c23fd7;p=openwrt%2Fstaging%2Fblocktrron.git ath79: add support for OpenMesh OM2P-HS v1 Device specifications: ====================== * Qualcomm/Atheros AR9341 rev 1 * 535/400/200 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 802.3af POE + builtin switch port 1 + used as LAN interface - eth1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 .bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp .bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/.bin Signed-off-by: Sven Eckelmann [drop redundant status from eth1] Signed-off-by: Adrian Schmutzler --- diff --git a/package/boot/uboot-envtools/Makefile b/package/boot/uboot-envtools/Makefile index 539e65e762..3493332cee 100644 --- a/package/boot/uboot-envtools/Makefile +++ b/package/boot/uboot-envtools/Makefile @@ -10,7 +10,7 @@ include $(TOPDIR)/rules.mk PKG_NAME:=uboot-envtools PKG_DISTNAME:=u-boot PKG_VERSION:=2020.04 -PKG_RELEASE:=11 +PKG_RELEASE:=12 PKG_SOURCE:=$(PKG_DISTNAME)-$(PKG_VERSION).tar.bz2 PKG_SOURCE_URL:= \ diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index a7564bc89e..bc69d35c96 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -86,6 +86,7 @@ netgear,wndr4300sw) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x20000" ;; openmesh,om2p-v4|\ +openmesh,om2p-hs-v1|\ openmesh,om2p-hs-v4|\ plasmacloud,pa300|\ plasmacloud,pa300e) diff --git a/target/linux/ath79/dts/ar9341_openmesh_om2p-hs-v1.dts b/target/linux/ath79/dts/ar9341_openmesh_om2p-hs-v1.dts new file mode 100644 index 0000000000..e1f14cd5c2 --- /dev/null +++ b/target/linux/ath79/dts/ar9341_openmesh_om2p-hs-v1.dts @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "ar9341_openmesh_om2p-hs.dtsi" + +/ { + compatible = "openmesh,om2p-hs-v1", "qca,ar9341"; + model = "OpenMesh OM2P-HS v1"; +}; diff --git a/target/linux/ath79/dts/ar9341_openmesh_om2p-hs.dtsi b/target/linux/ath79/dts/ar9341_openmesh_om2p-hs.dtsi new file mode 100644 index 0000000000..403ee940c1 --- /dev/null +++ b/target/linux/ath79/dts/ar9341_openmesh_om2p-hs.dtsi @@ -0,0 +1,161 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "ar9341.dtsi" + +#include +#include + +/ { + chosen { + /delete-property/ bootargs; + }; + + aliases { + serial0 = &uart; + led-boot = &led_power_blue; + led-failsafe = &led_power_blue; + led-running = &led_power_blue; + led-upgrade = &led_power_blue; + label-mac-device = ð1; + }; + + keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&jtag_disable_pins &led_lan_wan_blue_pin>; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power_blue: power_blue { + label = "blue:power"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wifi_green { + label = "green:wifi"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wifi_red { + label = "red:wifi"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + wifi_yellow { + label = "yellow:wifi"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + lan_blue { + label = "blue:lan"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + wan_blue { + label = "blue:wan"; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + hw_algo = "toggle"; + /* hw_margin_ms is actually 300s but driver limits it to 60s */ + hw_margin_ms = <60000>; + always-running; + }; +}; + +&ref { + clock-frequency = <40000000>; +}; + +&uart { + status = "okay"; +}; + +&pinmux { + led_lan_wan_blue_pin: pinmux_lan_wan_blue_pin { + pinctrl-single,bits = <0x10 0x0 0x0000ffff>; + }; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + + /* partitions are passed via bootloader */ + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x040000>; + }; + + partition@80000 { + label = "custom"; + reg = <0x080000 0x140000>; + read-only; + }; + + partition@1c0000 { + label = "inactive"; + reg = <0x1c0000 0x700000>; + }; + + partition@8c0000 { + label = "inactive2"; + reg = <0x8c0000 0x700000>; + }; + + art: partition@fc0000 { + label = "ART"; + reg = <0xfc0000 0x040000>; + read-only; + }; + }; + }; +}; + +ð0 { + status = "okay"; + + phy-handle = <&swphy4>; + + mtd-mac-address = <&art 0x6>; +}; + +ð1 { + mtd-mac-address = <&art 0x0>; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 5795e2a0ae..057bec3bc8 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -145,6 +145,7 @@ comfast,cf-e560ac) ucidef_set_led_switch "lan4" "LAN4" "blue:lan4" "switch0" "0x10" ;; comfast,cf-ew72|\ +openmesh,om2p-hs-v1|\ telco,t1) ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02" ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1" diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh index 6f0ab8f8a6..e3298cfc13 100644 --- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh +++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh @@ -51,6 +51,7 @@ platform_do_upgrade() { redboot_fis_do_upgrade "$1" linux ;; openmesh,om2p-v4|\ + openmesh,om2p-hs-v1|\ openmesh,om2p-hs-v4) PART_NAME="inactive" platform_do_upgrade_openmesh "$1" diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 66a39e06d2..1454c14e44 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1577,6 +1577,15 @@ define Device/openmesh_om2p-v4 endef TARGET_DEVICES += openmesh_om2p-v4 +define Device/openmesh_om2p-hs-v1 + $(Device/openmesh_om2p-common) + SOC := ar9341 + DEVICE_MODEL := OM2P-HS + DEVICE_VARIANT := v1 + SUPPORTED_DEVICES += om2p-hs +endef +TARGET_DEVICES += openmesh_om2p-hs-v1 + define Device/openmesh_om2p-hs-v4 $(Device/openmesh_om2p-common) SOC := qca9533