From: Sander Vanheule <sander@svanheule.net>
Date: Thu, 28 Jul 2022 13:13:52 +0000 (+0200)
Subject: realtek: remove support for HPE 1920 series
X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=a63aeaecf1f3387df020854c9b22a365207399ce;p=openwrt%2Fstaging%2Fblocktrron.git

realtek: remove support for HPE 1920 series

Support for HPE 1920 images depends on two non-existent tools (mkh3cimg
and mkh3cvfs) from the in the firmware-utils package. Revert commit
f2f09bc00280 ("realtek: add support for HPE 1920 series") until support
for these tools is merged and made available in OpenWrt.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
---

diff --git a/target/linux/realtek/base-files/etc/board.d/02_network b/target/linux/realtek/base-files/etc/board.d/02_network
index 5356bcac65..af9db848dd 100644
--- a/target/linux/realtek/base-files/etc/board.d/02_network
+++ b/target/linux/realtek/base-files/etc/board.d/02_network
@@ -22,20 +22,9 @@ ucidef_set_bridge_device switch
 ucidef_set_interface_lan "$lan_list"
 
 lan_mac=""
-lan_mac_start=""
 lan_mac_end=""
 label_mac=""
 case $board in
-hpe,1920-8g|\
-hpe,1920-16g|\
-hpe,1920-24g)
-	label_mac=$(mtd_get_mac_binary factory 0x68)
-	lan_mac=$label_mac
-	mac_count1=$(hexdump -v -n 4 -s 0x110 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
-	mac_count2=$(hexdump -v -n 4 -s 0x114 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
-	lan_mac_start=$(macaddr_add $lan_mac 2)
-	lan_mac_end=$(macaddr_add $lan_mac $((mac_count2-mac_count1)))
-	;;
 *)
 	lan_mac=$(mtd_get_mac_ascii u-boot-env2 mac_start)
 	lan_mac_end=$(mtd_get_mac_ascii u-boot-env2 mac_end)
@@ -47,11 +36,10 @@ esac
 ucidef_set_interface_macaddr "lan" $lan_mac
 ucidef_set_bridge_mac "$lan_mac"
 ucidef_set_network_device_mac eth0 $lan_mac
-[ -z "$lan_mac_start" ] && lan_mac_start=$lan_mac
 for lan in $lan_list; do
-	ucidef_set_network_device_mac $lan $lan_mac_start
-	[ -z "$lan_mac_end" ] || [ "$lan_mac_start" == "$lan_mac_end" ] && lan_mac_start=$(macaddr_setbit_la $lan_mac_start)
-	lan_mac_start=$(macaddr_add $lan_mac_start 1)
+	ucidef_set_network_device_mac $lan $lan_mac
+	[ -z "$lan_mac_end" ] || [ "$lan_mac" == "$lan_mac_end" ] && lan_mac=$(macaddr_setbit_la $lan_mac)
+	lan_mac=$(macaddr_add $lan_mac 1)
 done
 [ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
 
diff --git a/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts b/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts
deleted file mode 100644
index b51c75f355..0000000000
--- a/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts
+++ /dev/null
@@ -1,113 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "rtl838x.dtsi"
-#include "rtl838x_hpe_1920.dtsi"
-
-/ {
-	compatible = "hpe,1920-8g", "realtek,rtl838x-soc";
-	model = "HPE 1920-8G (JG920A)";
-
-	gpio1: rtl8231-gpio {
-		compatible = "realtek,rtl8231-gpio";
-		#gpio-cells = <2>;
-		gpio-controller;
-		indirect-access-bus-id = <0>;
-	};
-
-	i2c0: i2c-gpio-0 {
-		compatible = "i2c-gpio";
-		sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		i2c-gpio,delay-us = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-	};
-
-	sfp0: sfp-0 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c0>;
-		los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
-		// tx-fault and tx-disable unconnected
-	};
-
-	i2c1: i2c-gpio-1 {
-		compatible = "i2c-gpio";
-		sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		i2c-gpio,delay-us = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-	};
-
-	sfp1: sfp-1 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c1>;
-		los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
-		// tx-fault and tx-disable unconnected
-	};
-};
-
-&ethernet0 {
-	mdio: mdio-bus {
-		compatible = "realtek,rtl838x-mdio";
-		regmap = <&ethernet0>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		INTERNAL_PHY(8)
-		INTERNAL_PHY(9)
-		INTERNAL_PHY(10)
-		INTERNAL_PHY(11)
-		INTERNAL_PHY(12)
-		INTERNAL_PHY(13)
-		INTERNAL_PHY(14)
-		INTERNAL_PHY(15)
-
-		INTERNAL_PHY(24)
-		INTERNAL_PHY(26)
-	};
-};
-
-&switch0 {
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		SWITCH_PORT(8, 1, internal)
-		SWITCH_PORT(9, 2, internal)
-		SWITCH_PORT(10, 3, internal)
-		SWITCH_PORT(11, 4, internal)
-		SWITCH_PORT(12, 5, internal)
-		SWITCH_PORT(13, 6, internal)
-		SWITCH_PORT(14, 7, internal)
-		SWITCH_PORT(15, 8, internal)
-
-		port@24 {
-			reg = <24>;
-			label = "lan9";
-			phy-mode = "1000base-x";
-			managed = "in-band-status";
-			sfp = <&sfp0>;
-		};
-
-		port@26 {
-			reg = <26>;
-			label = "lan10";
-			phy-mode = "1000base-x";
-			managed = "in-band-status";
-			sfp = <&sfp1>;
-		};
-
-		port@28 {
-			ethernet = <&ethernet0>;
-			reg = <28>;
-			phy-mode = "internal";
-			fixed-link {
-				speed = <1000>;
-				full-duplex;
-			};
-		};
-	};
-};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts
deleted file mode 100644
index 59043b2f6f..0000000000
--- a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "rtl8382_hpe_1920.dtsi"
-
-/ {
-	compatible = "hpe,1920-16g", "realtek,rtl838x-soc";
-	model = "HPE 1920-16G (JG923A)";
-};
-
-&switch0 {
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		SWITCH_PORT(8, 1, internal)
-		SWITCH_PORT(9, 2, internal)
-		SWITCH_PORT(10, 3, internal)
-		SWITCH_PORT(11, 4, internal)
-		SWITCH_PORT(12, 5, internal)
-		SWITCH_PORT(13, 6, internal)
-		SWITCH_PORT(14, 7, internal)
-		SWITCH_PORT(15, 8, internal)
-
-		SWITCH_PORT(16, 9, qsgmii)
-		SWITCH_PORT(17, 10, qsgmii)
-		SWITCH_PORT(18, 11, qsgmii)
-		SWITCH_PORT(19, 12, qsgmii)
-		SWITCH_PORT(20, 13, qsgmii)
-		SWITCH_PORT(21, 14, qsgmii)
-		SWITCH_PORT(22, 15, qsgmii)
-		SWITCH_PORT(23, 16, qsgmii)
-
-		SWITCH_PORT(24, 17, qsgmii)
-		SWITCH_PORT(25, 18, qsgmii)
-		SWITCH_PORT(26, 19, qsgmii)
-		SWITCH_PORT(27, 20, qsgmii)
-
-		port@28 {
-			ethernet = <&ethernet0>;
-			reg = <28>;
-			phy-mode = "internal";
-			fixed-link {
-				speed = <1000>;
-				full-duplex;
-			};
-		};
-	};
-};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts
deleted file mode 100644
index 61781c708e..0000000000
--- a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts
+++ /dev/null
@@ -1,68 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "rtl8382_hpe_1920.dtsi"
-
-/ {
-	compatible = "hpe,1920-24g", "realtek,rtl838x-soc";
-	model = "HPE 1920-24G (JG924A)";
-};
-
-&mdio {
-	EXTERNAL_PHY(0)
-	EXTERNAL_PHY(1)
-	EXTERNAL_PHY(2)
-	EXTERNAL_PHY(3)
-	EXTERNAL_PHY(4)
-	EXTERNAL_PHY(5)
-	EXTERNAL_PHY(6)
-	EXTERNAL_PHY(7)
-};
-
-&switch0 {
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		SWITCH_PORT(0, 1, qsgmii)
-		SWITCH_PORT(1, 2, qsgmii)
-		SWITCH_PORT(2, 3, qsgmii)
-		SWITCH_PORT(3, 4, qsgmii)
-		SWITCH_PORT(4, 5, qsgmii)
-		SWITCH_PORT(5, 6, qsgmii)
-		SWITCH_PORT(6, 7, qsgmii)
-		SWITCH_PORT(7, 8, qsgmii)
-
-		SWITCH_PORT(8, 9, internal)
-		SWITCH_PORT(9, 10, internal)
-		SWITCH_PORT(10, 11, internal)
-		SWITCH_PORT(11, 12, internal)
-		SWITCH_PORT(12, 13, internal)
-		SWITCH_PORT(13, 14, internal)
-		SWITCH_PORT(14, 15, internal)
-		SWITCH_PORT(15, 16, internal)
-
-		SWITCH_PORT(16, 17, qsgmii)
-		SWITCH_PORT(17, 18, qsgmii)
-		SWITCH_PORT(18, 19, qsgmii)
-		SWITCH_PORT(19, 20, qsgmii)
-		SWITCH_PORT(20, 21, qsgmii)
-		SWITCH_PORT(21, 22, qsgmii)
-		SWITCH_PORT(22, 23, qsgmii)
-		SWITCH_PORT(23, 24, qsgmii)
-
-		SWITCH_PORT(24, 25, qsgmii)
-		SWITCH_PORT(25, 26, qsgmii)
-		SWITCH_PORT(26, 27, qsgmii)
-		SWITCH_PORT(27, 28, qsgmii)
-
-		port@28 {
-			ethernet = <&ethernet0>;
-			reg = <28>;
-			phy-mode = "internal";
-			fixed-link {
-				speed = <1000>;
-				full-duplex;
-			};
-		};
-	};
-};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi
deleted file mode 100644
index 5368b41c27..0000000000
--- a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi
+++ /dev/null
@@ -1,117 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "rtl838x.dtsi"
-#include "rtl838x_hpe_1920.dtsi"
-
-/ {
-	gpio1: rtl8231-gpio {
-		compatible = "realtek,rtl8231-gpio";
-		#gpio-cells = <2>;
-		gpio-controller;
-		indirect-access-bus-id = <0>;
-	};
-
-	i2c0: i2c-gpio-0 {
-		compatible = "i2c-gpio";
-		sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		i2c-gpio,delay-us = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-	};
-
-	sfp0: sfp-0 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c0>;
-		los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
-		// tx-fault unconnected
-		// tx-disable connected to RTL8214FC
-	};
-
-	i2c1: i2c-gpio-1 {
-		compatible = "i2c-gpio";
-		sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		i2c-gpio,delay-us = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-	};
-
-	sfp1: sfp-1 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c1>;
-		los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
-		// tx-fault unconnected
-		// tx-disable connected to RTL8214FC
-	};
-
-	i2c2: i2c-gpio-2 {
-		compatible = "i2c-gpio";
-		sda-gpios = <&gpio1 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		i2c-gpio,delay-us = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-	};
-
-	sfp2: sfp-2 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c2>;
-		los-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
-		// tx-fault unconnected
-		// tx-disable connected to RTL8214FC
-	};
-
-	i2c3: i2c-gpio-3 {
-		compatible = "i2c-gpio";
-		sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&gpio1 32 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		i2c-gpio,delay-us = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-	};
-
-	sfp3: sfp-3 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c3>;
-		los-gpio = <&gpio1 34 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&gpio1 33 GPIO_ACTIVE_LOW>;
-		// tx-fault unconnected
-		// tx-disable connected to RTL8214FC
-	};
-};
-
-&ethernet0 {
-	mdio: mdio-bus {
-		compatible = "realtek,rtl838x-mdio";
-		regmap = <&ethernet0>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		INTERNAL_PHY(8)
-		INTERNAL_PHY(9)
-		INTERNAL_PHY(10)
-		INTERNAL_PHY(11)
-		INTERNAL_PHY(12)
-		INTERNAL_PHY(13)
-		INTERNAL_PHY(14)
-		INTERNAL_PHY(15)
-
-		EXTERNAL_PHY(16)
-		EXTERNAL_PHY(17)
-		EXTERNAL_PHY(18)
-		EXTERNAL_PHY(19)
-		EXTERNAL_PHY(20)
-		EXTERNAL_PHY(21)
-		EXTERNAL_PHY(22)
-		EXTERNAL_PHY(23)
-
-		EXTERNAL_SFP_PHY_FULL(24, 0)
-		EXTERNAL_SFP_PHY_FULL(25, 1)
-		EXTERNAL_SFP_PHY_FULL(26, 2)
-		EXTERNAL_SFP_PHY_FULL(27, 3)
-	};
-};
diff --git a/target/linux/realtek/dts-5.10/rtl838x.dtsi b/target/linux/realtek/dts-5.10/rtl838x.dtsi
index 41fdbdae20..11cabc3f63 100644
--- a/target/linux/realtek/dts-5.10/rtl838x.dtsi
+++ b/target/linux/realtek/dts-5.10/rtl838x.dtsi
@@ -27,13 +27,6 @@
 		reg = <##n>; \
 	};
 
-#define EXTERNAL_SFP_PHY_FULL(n, s) \
-	phy##n: ethernet-phy@##n { \
-		compatible = "ethernet-phy-ieee802.3-c22"; \
-		sfp = <&sfp##s>; \
-		reg = <##n>; \
-	};
-
 #define SWITCH_PORT(n, s, m) \
 	port@##n { \
 		reg = <##n>; \
diff --git a/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi
deleted file mode 100644
index 8e29af62bb..0000000000
--- a/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi
+++ /dev/null
@@ -1,96 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	chosen {
-		bootargs = "console=ttyS0,38400";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x8000000>;
-	};
-
-	watchdog1: watchdog {
-		// PT7A7514
-		compatible = "linux,wdt-gpio";
-		gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
-		hw_algo = "toggle";
-		hw_margin_ms = <1000>;
-		always-running;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinmux_disable_sys_led>;
-	};
-};
-
-&watchdog0 {
-	status = "disabled";
-};
-
-&spi0 {
-	status = "okay";
-
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <50000000>;
-		m25p,fast-read;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "bootware_basic";
-				reg = <0x0 0x50000>;
-				read-only;
-			};
-
-			partition@0x60000 {
-				label = "bootware_data";
-				reg = <0x60000 0x30000>;
-				read-only;
-			};
-
-			partition@0x90000 {
-				label = "bootware_extend";
-				reg = <0x90000 0x40000>;
-				read-only;
-			};
-
-			partition@0x100000 {
-				label = "bootware_basic_backup";
-				reg = <0x100000 0x50000>;
-				read-only;
-			};
-
-			partition@0x160000 {
-				label = "bootware_data_backup";
-				reg = <0x160000 0x30000>;
-				read-only;
-			};
-
-			partition@0x190000 {
-				label = "bootware_extend_backup";
-				reg = <0x190000 0x40000>;
-				read-only;
-			};
-
-			partition@0x300000 {
-				label = "firmware";
-				compatible = "h3c,vfs-firmware";
-				reg = <0x300000 0x1cf0000>;
-			};
-
-			partition@0x1ff0000 {
-				label = "factory";
-				reg = <0x1ff0000 0x10000>;
-				read-only;
-			};
-		};
-	};
-};
diff --git a/target/linux/realtek/image/Makefile b/target/linux/realtek/image/Makefile
index 6165d99bfc..cf779002e8 100644
--- a/target/linux/realtek/image/Makefile
+++ b/target/linux/realtek/image/Makefile
@@ -8,7 +8,6 @@ KERNEL_ENTRY = 0x80000400
 
 DEVICE_VARS += ZYXEL_VERS DLINK_KERNEL_PART_SIZE
 DEVICE_VARS += CAMEO_KERNEL_PART CAMEO_ROOTFS_PART CAMEO_CUSTOMER_SIGNATURE CAMEO_BOARD_VERSION
-DEVICE_VARS += H3C_PRODUCT_ID H3C_DEVICE_ID
 
 define Build/zyxel-vers
        ( echo VERS;\
@@ -42,43 +41,6 @@ define Build/dlink-headers
         cat $@.kernel_part.hex $@.rootfs_part.hex > $@
 endef
 
-define Build/7z
-	$(STAGING_DIR_HOST)/bin/7zr a $(@).new -t7z -m0=lzma $(@)
-	mv $@.new $@
-endef
-
-define Build/h3c-image
-	$(STAGING_DIR_HOST)/bin/mkh3cimg \
-		-i $(@) \
-		-o $(@).new \
-		-c 7z \
-		-p $(H3C_PRODUCT_ID) \
-		-d $(H3C_DEVICE_ID)
-	mv $@.new $@
-endef
-
-define Build/h3c-vfs
-	$(STAGING_DIR_HOST)/bin/mkh3cvfs \
-		-i $(@) \
-		-o $(@).new \
-		-f openwrt-kernel.bin
-	mv $@.new $@
-endef
-
-define Build/relocate-kernel
-	rm -rf $@.relocate
-	$(CP) ../../generic/image/relocate $@.relocate
-	$(MAKE) -j1 -C $@.relocate KERNEL_ADDR=$(KERNEL_LOADADDR) LZMA_TEXT_START=0x82000000 \
-		CROSS_COMPILE=$(TARGET_CROSS)
-	( \
-		dd if=$@.relocate/loader.bin bs=32 conv=sync && \
-		perl -e '@s = stat("$@"); print pack("N", @s[7])' && \
-		cat "$@" \
-	) > "$@.new"
-	mv "$@.new" "$@"
-	rm -rf $@.relocate
-endef
-
 define Device/Default
   PROFILES = Default
   KERNEL := kernel-bin | append-dtb | gzip | uImage gzip
@@ -90,17 +52,6 @@ define Device/Default
 	check-size | append-metadata
 endef
 
-define Device/hpe_1920
-  DEVICE_VENDOR := HPE
-  IMAGE_SIZE := 29632k
-  BLOCKSIZE := 64k
-  H3C_PRODUCT_ID := 0x3c010501
-  KERNEL := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image | h3c-vfs
-  KERNEL_INITRAMFS := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image
-  IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
-  	pad-rootfs | check-size | append-metadata
-endef
-
 # "NGE" refers to the uImage magic
 define Device/netgear_nge
   KERNEL := kernel-bin | append-dtb | lzma | uImage lzma
diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk
index 60eda5359d..887f82e385 100644
--- a/target/linux/realtek/image/rtl838x.mk
+++ b/target/linux/realtek/image/rtl838x.mk
@@ -65,30 +65,6 @@ define Device/engenius_ews2910p
 endef
 TARGET_DEVICES += engenius_ews2910p
 
-define Device/hpe_1920-8g
-  $(Device/hpe_1920)
-  SOC := rtl8380
-  DEVICE_MODEL := 1920-8G (JG920A)
-  H3C_DEVICE_ID := 0x00010023
-endef
-TARGET_DEVICES += hpe_1920-8g
-
-define Device/hpe_1920-16g
-  $(Device/hpe_1920)
-  SOC := rtl8382
-  DEVICE_MODEL := 1920-16G (JG923A)
-  H3C_DEVICE_ID := 0x00010026
-endef
-TARGET_DEVICES += hpe_1920-16g
-
-define Device/hpe_1920-24g
-  $(Device/hpe_1920)
-  SOC := rtl8382
-  DEVICE_MODEL := 1920-24G (JG924A)
-  H3C_DEVICE_ID := 0x00010027
-endef
-TARGET_DEVICES += hpe_1920-24g
-
 define Device/inaba_aml2-17gp
   SOC := rtl8382
   IMAGE_SIZE := 13504k
diff --git a/target/linux/realtek/rtl838x/config-5.10 b/target/linux/realtek/rtl838x/config-5.10
index 9075aa6d3c..c117fc489a 100644
--- a/target/linux/realtek/rtl838x/config-5.10
+++ b/target/linux/realtek/rtl838x/config-5.10
@@ -74,8 +74,6 @@ CONFIG_GPIO_PCA953X=y
 CONFIG_GPIO_PCA953X_IRQ=y
 CONFIG_GPIO_REALTEK_OTTO=y
 CONFIG_GPIO_RTL8231=y
-CONFIG_GPIO_WATCHDOG=y
-# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
 CONFIG_GRO_CELLS=y
 CONFIG_HANDLE_DOMAIN_IRQ=y
 CONFIG_HARDWARE_WATCHPOINTS=y
@@ -136,7 +134,6 @@ CONFIG_MTD_SPI_NOR=y
 CONFIG_MTD_SPLIT_BRNIMAGE_FW=y
 CONFIG_MTD_SPLIT_EVA_FW=y
 CONFIG_MTD_SPLIT_FIRMWARE=y
-CONFIG_MTD_SPLIT_H3C_VFS=y
 CONFIG_MTD_SPLIT_TPLINK_FW=y
 CONFIG_MTD_SPLIT_UIMAGE_FW=y
 CONFIG_NEED_DMA_MAP_STATE=y