From: Tianling Shen Date: Tue, 30 May 2023 04:59:07 +0000 (+0800) Subject: rockchip: add Orange Pi R1 Plus support X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=ab641efe698f4412319fcbcfe6ffde64c929cd97;p=openwrt%2Fstaging%2Fdangole.git rockchip: add Orange Pi R1 Plus support Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong. This device is similar to the NanoPi R2S, and has a 16MB SPI NOR (mx25l12805d). The reset button is changed to directly reset the power supply, another detail is that both network ports have independent MAC addresses. Note: booting from SPI is currently unsupported, you have to install the image on a SD card. Signed-off-by: Tianling Shen --- diff --git a/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds b/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds index 2c9206b03e..f0da262a09 100644 --- a/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds +++ b/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds @@ -10,7 +10,8 @@ board_config_update case $board in friendlyarm,nanopi-r2c|\ friendlyarm,nanopi-r2s|\ -friendlyarm,nanopi-r4s) +friendlyarm,nanopi-r4s|\ +xunlong,orangepi-r1-plus) ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth0" ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth1" ;; diff --git a/target/linux/rockchip/armv8/base-files/etc/board.d/02_network b/target/linux/rockchip/armv8/base-files/etc/board.d/02_network index 16ba01b7e3..f7e0da67b2 100644 --- a/target/linux/rockchip/armv8/base-files/etc/board.d/02_network +++ b/target/linux/rockchip/armv8/base-files/etc/board.d/02_network @@ -8,7 +8,8 @@ rockchip_setup_interfaces() case "$board" in friendlyarm,nanopi-r2s|\ - friendlyarm,nanopi-r4s) + friendlyarm,nanopi-r4s|\ + xunlong,orangepi-r1-plus) ucidef_set_interfaces_lan_wan 'eth1' 'eth0' ;; *) @@ -55,6 +56,9 @@ rockchip_setup_macs() wan_mac=$(nanopi_r4s_get_mac wan) lan_mac=$(nanopi_r4s_get_mac lan) ;; + xunlong,orangepi-r1-plus) + wan_mac=$(macaddr_add "$(cat /sys/class/net/eth1/address)" -1) + ;; esac [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac diff --git a/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity b/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity index 3d1d99128e..660a7e2866 100644 --- a/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity +++ b/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity @@ -30,7 +30,8 @@ set_interface_core() { case "$(board_name)" in friendlyarm,nanopi-r2c|\ -friendlyarm,nanopi-r2s) +friendlyarm,nanopi-r2s|\ +xunlong,orangepi-r1-plus) set_interface_core 2 "eth0" set_interface_core 4 "eth1" "xhci-hcd:usb3" ;; diff --git a/target/linux/rockchip/image/armv8.mk b/target/linux/rockchip/image/armv8.mk index 601ddcbdd6..9a32a07b21 100644 --- a/target/linux/rockchip/image/armv8.mk +++ b/target/linux/rockchip/image/armv8.mk @@ -60,3 +60,12 @@ define Device/radxa_rock-pi-4a IMAGE/sysupgrade.img.gz := boot-common | boot-script | pine64-img | gzip | append-metadata endef TARGET_DEVICES += radxa_rock-pi-4a + +define Device/xunlong_orangepi-r1-plus + DEVICE_VENDOR := Xunlong + DEVICE_MODEL := Orange Pi R1 Plus + SOC := rk3328 + IMAGE/sysupgrade.img.gz := boot-common | boot-script | pine64-img | gzip | append-metadata + DEVICE_PACKAGES := kmod-usb-net-rtl8152 +endef +TARGET_DEVICES += xunlong_orangepi-r1-plus diff --git a/target/linux/rockchip/patches-5.15/007-v6.3-arm64-dts-rockchip-rk3328-Add-Orange-Pi-R1-Plus.patch b/target/linux/rockchip/patches-5.15/007-v6.3-arm64-dts-rockchip-rk3328-Add-Orange-Pi-R1-Plus.patch new file mode 100644 index 0000000000..053a4d0d8e --- /dev/null +++ b/target/linux/rockchip/patches-5.15/007-v6.3-arm64-dts-rockchip-rk3328-Add-Orange-Pi-R1-Plus.patch @@ -0,0 +1,407 @@ +From 51712e1d014aaaa4c6e1e7e84932d58b5c0f59ed Mon Sep 17 00:00:00 2001 +From: Chukun Pan +Date: Sat, 3 Dec 2022 15:41:49 +0800 +Subject: [PATCH] arm64: dts: rockchip: rk3328: Add Orange Pi R1 Plus + +Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong. + +This device is similar to the NanoPi R2S, and has a 16MB +SPI NOR (mx25l12805d). The reset button is changed to +directly reset the power supply, another detail is that +both network ports have independent MAC addresses. + +Signed-off-by: Chukun Pan +Link: https://lore.kernel.org/r/20221203074149.11543-3-amadeus@jmu.edu.cn +Signed-off-by: Heiko Stuebner +--- + arch/arm64/boot/dts/rockchip/Makefile | 1 + + .../dts/rockchip/rk3328-orangepi-r1-plus.dts | 373 ++++++++++++++++++ + 2 files changed, 374 insertions(+) + create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts + +--- a/arch/arm64/boot/dts/rockchip/Makefile ++++ b/arch/arm64/boot/dts/rockchip/Makefile +@@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1 + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2c.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb ++dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-orangepi-r1-plus.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock-pi-e.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb +--- /dev/null ++++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts +@@ -0,0 +1,373 @@ ++// SPDX-License-Identifier: (GPL-2.0+ OR MIT) ++/* ++ * Based on rk3328-nanopi-r2s.dts, which is: ++ * Copyright (c) 2020 David Bauer ++ */ ++ ++/dts-v1/; ++ ++#include ++#include ++#include "rk3328.dtsi" ++ ++/ { ++ model = "Xunlong Orange Pi R1 Plus"; ++ compatible = "xunlong,orangepi-r1-plus", "rockchip,rk3328"; ++ ++ aliases { ++ ethernet1 = &rtl8153; ++ mmc0 = &sdmmc; ++ }; ++ ++ chosen { ++ stdout-path = "serial2:1500000n8"; ++ }; ++ ++ gmac_clk: gmac-clock { ++ compatible = "fixed-clock"; ++ clock-frequency = <125000000>; ++ clock-output-names = "gmac_clkin"; ++ #clock-cells = <0>; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>; ++ pinctrl-names = "default"; ++ ++ led-0 { ++ function = LED_FUNCTION_LAN; ++ color = ; ++ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ led-1 { ++ function = LED_FUNCTION_STATUS; ++ color = ; ++ gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "heartbeat"; ++ }; ++ ++ led-2 { ++ function = LED_FUNCTION_WAN; ++ color = ; ++ gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ ++ vcc_sd: sdmmc-regulator { ++ compatible = "regulator-fixed"; ++ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>; ++ pinctrl-0 = <&sdmmc0m1_pin>; ++ pinctrl-names = "default"; ++ regulator-name = "vcc_sd"; ++ regulator-boot-on; ++ vin-supply = <&vcc_io>; ++ }; ++ ++ vcc_sys: vcc-sys-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc_sys"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ }; ++ ++ vdd_5v_lan: vdd-5v-lan-regulator { ++ compatible = "regulator-fixed"; ++ enable-active-high; ++ gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>; ++ pinctrl-0 = <&lan_vdd_pin>; ++ pinctrl-names = "default"; ++ regulator-name = "vdd_5v_lan"; ++ regulator-always-on; ++ regulator-boot-on; ++ vin-supply = <&vcc_sys>; ++ }; ++}; ++ ++&cpu0 { ++ cpu-supply = <&vdd_arm>; ++}; ++ ++&cpu1 { ++ cpu-supply = <&vdd_arm>; ++}; ++ ++&cpu2 { ++ cpu-supply = <&vdd_arm>; ++}; ++ ++&cpu3 { ++ cpu-supply = <&vdd_arm>; ++}; ++ ++&display_subsystem { ++ status = "disabled"; ++}; ++ ++&gmac2io { ++ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>; ++ assigned-clock-parents = <&gmac_clk>, <&gmac_clk>; ++ clock_in_out = "input"; ++ phy-handle = <&rtl8211e>; ++ phy-mode = "rgmii"; ++ phy-supply = <&vcc_io>; ++ pinctrl-0 = <&rgmiim1_pins>; ++ pinctrl-names = "default"; ++ snps,aal; ++ rx_delay = <0x18>; ++ tx_delay = <0x24>; ++ status = "okay"; ++ ++ mdio { ++ compatible = "snps,dwmac-mdio"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ rtl8211e: ethernet-phy@1 { ++ reg = <1>; ++ pinctrl-0 = <ð_phy_reset_pin>; ++ pinctrl-names = "default"; ++ reset-assert-us = <10000>; ++ reset-deassert-us = <50000>; ++ reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++}; ++ ++&i2c1 { ++ status = "okay"; ++ ++ rk805: pmic@18 { ++ compatible = "rockchip,rk805"; ++ reg = <0x18>; ++ interrupt-parent = <&gpio1>; ++ interrupts = <24 IRQ_TYPE_LEVEL_LOW>; ++ #clock-cells = <1>; ++ clock-output-names = "xin32k", "rk805-clkout2"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ pinctrl-0 = <&pmic_int_l>; ++ pinctrl-names = "default"; ++ rockchip,system-power-controller; ++ wakeup-source; ++ ++ vcc1-supply = <&vcc_sys>; ++ vcc2-supply = <&vcc_sys>; ++ vcc3-supply = <&vcc_sys>; ++ vcc4-supply = <&vcc_sys>; ++ vcc5-supply = <&vcc_io>; ++ vcc6-supply = <&vcc_sys>; ++ ++ regulators { ++ vdd_log: DCDC_REG1 { ++ regulator-name = "vdd_log"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <712500>; ++ regulator-max-microvolt = <1450000>; ++ regulator-ramp-delay = <12500>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <1000000>; ++ }; ++ }; ++ ++ vdd_arm: DCDC_REG2 { ++ regulator-name = "vdd_arm"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <712500>; ++ regulator-max-microvolt = <1450000>; ++ regulator-ramp-delay = <12500>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <950000>; ++ }; ++ }; ++ ++ vcc_ddr: DCDC_REG3 { ++ regulator-name = "vcc_ddr"; ++ regulator-always-on; ++ regulator-boot-on; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ }; ++ }; ++ ++ vcc_io: DCDC_REG4 { ++ regulator-name = "vcc_io"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <3300000>; ++ }; ++ }; ++ ++ vcc_18: LDO_REG1 { ++ regulator-name = "vcc_18"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <1800000>; ++ }; ++ }; ++ ++ vcc18_emmc: LDO_REG2 { ++ regulator-name = "vcc18_emmc"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <1800000>; ++ }; ++ }; ++ ++ vdd_10: LDO_REG3 { ++ regulator-name = "vdd_10"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1000000>; ++ regulator-max-microvolt = <1000000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <1000000>; ++ }; ++ }; ++ }; ++ }; ++}; ++ ++&io_domains { ++ pmuio-supply = <&vcc_io>; ++ vccio1-supply = <&vcc_io>; ++ vccio2-supply = <&vcc18_emmc>; ++ vccio3-supply = <&vcc_io>; ++ vccio4-supply = <&vcc_io>; ++ vccio5-supply = <&vcc_io>; ++ vccio6-supply = <&vcc_io>; ++ status = "okay"; ++}; ++ ++&pinctrl { ++ gmac2io { ++ eth_phy_reset_pin: eth-phy-reset-pin { ++ rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>; ++ }; ++ }; ++ ++ leds { ++ lan_led_pin: lan-led-pin { ++ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ ++ sys_led_pin: sys-led-pin { ++ rockchip,pins = <3 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ ++ wan_led_pin: wan-led-pin { ++ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ }; ++ ++ lan { ++ lan_vdd_pin: lan-vdd-pin { ++ rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ }; ++ ++ pmic { ++ pmic_int_l: pmic-int-l { ++ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>; ++ }; ++ }; ++}; ++ ++&pwm2 { ++ status = "okay"; ++}; ++ ++&sdmmc { ++ bus-width = <4>; ++ cap-sd-highspeed; ++ disable-wp; ++ pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>; ++ pinctrl-names = "default"; ++ vmmc-supply = <&vcc_sd>; ++ status = "okay"; ++}; ++ ++&spi0 { ++ status = "okay"; ++ ++ flash@0 { ++ compatible = "jedec,spi-nor"; ++ reg = <0>; ++ spi-max-frequency = <50000000>; ++ }; ++}; ++ ++&tsadc { ++ rockchip,hw-tshut-mode = <0>; ++ rockchip,hw-tshut-polarity = <0>; ++ status = "okay"; ++}; ++ ++&u2phy { ++ status = "okay"; ++}; ++ ++&u2phy_host { ++ status = "okay"; ++}; ++ ++&u2phy_otg { ++ status = "okay"; ++}; ++ ++&uart2 { ++ status = "okay"; ++}; ++ ++&usb20_otg { ++ dr_mode = "host"; ++ status = "okay"; ++}; ++ ++&usbdrd3 { ++ dr_mode = "host"; ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ /* Second port is for USB 3.0 */ ++ rtl8153: device@2 { ++ compatible = "usbbda,8153"; ++ reg = <2>; ++ }; ++}; ++ ++&usb_host0_ehci { ++ status = "okay"; ++}; ++ ++&usb_host0_ohci { ++ status = "okay"; ++}; diff --git a/target/linux/rockchip/patches-5.15/107-arm64-dts-rockchip-Update-LED-properties-for-Orange-.patch b/target/linux/rockchip/patches-5.15/107-arm64-dts-rockchip-Update-LED-properties-for-Orange-.patch new file mode 100644 index 0000000000..b1e26d4e3e --- /dev/null +++ b/target/linux/rockchip/patches-5.15/107-arm64-dts-rockchip-Update-LED-properties-for-Orange-.patch @@ -0,0 +1,56 @@ +From d2166e3b3680bd2b206aebf1e1ce4c0d346f3c50 Mon Sep 17 00:00:00 2001 +From: Tianling Shen +Date: Fri, 19 May 2023 12:10:52 +0800 +Subject: [PATCH] arm64: dts: rockchip: Update LED properties for Orange Pi R1 + Plus + +Add OpenWrt's LED aliases for showing system status. +Also replace function/color with legacy label as OpenWrt relys on it +to update LED settings. + +Signed-off-by: Tianling Shen +--- + .../dts/rockchip/rk3328-orangepi-r1-plus.dts | 17 +++++++++-------- + 1 file changed, 9 insertions(+), 8 deletions(-) + +--- a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts ++++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts +@@ -17,6 +17,11 @@ + aliases { + ethernet1 = &rtl8153; + mmc0 = &sdmmc; ++ ++ led-boot = &status_led; ++ led-failsafe = &status_led; ++ led-running = &status_led; ++ led-upgrade = &status_led; + }; + + chosen { +@@ -36,22 +41,18 @@ + pinctrl-names = "default"; + + led-0 { +- function = LED_FUNCTION_LAN; +- color = ; + gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>; ++ label = "green:lan"; + }; + +- led-1 { +- function = LED_FUNCTION_STATUS; +- color = ; ++ status_led: led-1 { + gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>; +- linux,default-trigger = "heartbeat"; ++ label = "red:status"; + }; + + led-2 { +- function = LED_FUNCTION_WAN; +- color = ; + gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>; ++ label = "green:wan"; + }; + }; + diff --git a/target/linux/rockchip/patches-5.15/108-arm64-dts-rockchip-add-LED-configuration-to-Orange-P.patch b/target/linux/rockchip/patches-5.15/108-arm64-dts-rockchip-add-LED-configuration-to-Orange-P.patch new file mode 100644 index 0000000000..37b59925fc --- /dev/null +++ b/target/linux/rockchip/patches-5.15/108-arm64-dts-rockchip-add-LED-configuration-to-Orange-P.patch @@ -0,0 +1,24 @@ +From b46a530d12ada422b9d5b2b97059e0d3ed950b40 Mon Sep 17 00:00:00 2001 +From: Tianling Shen +Date: Fri, 19 May 2023 12:38:04 +0800 +Subject: [PATCH] arm64: dts: rockchip: add LED configuration to Orange Pi R1 + Plus + +Add the correct value for the RTL8153 LED configuration register to +match the blink behavior of the other port on the device. + +Signed-off-by: Tianling Shen +--- + arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts | 1 + + 1 file changed, 1 insertion(+) + +--- a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts ++++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts +@@ -362,6 +362,7 @@ + rtl8153: device@2 { + compatible = "usbbda,8153"; + reg = <2>; ++ realtek,led-data = <0x87>; + }; + }; + diff --git a/target/linux/rockchip/patches-6.1/007-v6.3-arm64-dts-rockchip-rk3328-Add-Orange-Pi-R1-Plus.patch b/target/linux/rockchip/patches-6.1/007-v6.3-arm64-dts-rockchip-rk3328-Add-Orange-Pi-R1-Plus.patch new file mode 100644 index 0000000000..4e48218b89 --- /dev/null +++ b/target/linux/rockchip/patches-6.1/007-v6.3-arm64-dts-rockchip-rk3328-Add-Orange-Pi-R1-Plus.patch @@ -0,0 +1,407 @@ +From 51712e1d014aaaa4c6e1e7e84932d58b5c0f59ed Mon Sep 17 00:00:00 2001 +From: Chukun Pan +Date: Sat, 3 Dec 2022 15:41:49 +0800 +Subject: [PATCH] arm64: dts: rockchip: rk3328: Add Orange Pi R1 Plus + +Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong. + +This device is similar to the NanoPi R2S, and has a 16MB +SPI NOR (mx25l12805d). The reset button is changed to +directly reset the power supply, another detail is that +both network ports have independent MAC addresses. + +Signed-off-by: Chukun Pan +Link: https://lore.kernel.org/r/20221203074149.11543-3-amadeus@jmu.edu.cn +Signed-off-by: Heiko Stuebner +--- + arch/arm64/boot/dts/rockchip/Makefile | 1 + + .../dts/rockchip/rk3328-orangepi-r1-plus.dts | 373 ++++++++++++++++++ + 2 files changed, 374 insertions(+) + create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts + +--- a/arch/arm64/boot/dts/rockchip/Makefile ++++ b/arch/arm64/boot/dts/rockchip/Makefile +@@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1 + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2c.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb ++dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-orangepi-r1-plus.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock-pi-e.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb +--- /dev/null ++++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts +@@ -0,0 +1,373 @@ ++// SPDX-License-Identifier: (GPL-2.0+ OR MIT) ++/* ++ * Based on rk3328-nanopi-r2s.dts, which is: ++ * Copyright (c) 2020 David Bauer ++ */ ++ ++/dts-v1/; ++ ++#include ++#include ++#include "rk3328.dtsi" ++ ++/ { ++ model = "Xunlong Orange Pi R1 Plus"; ++ compatible = "xunlong,orangepi-r1-plus", "rockchip,rk3328"; ++ ++ aliases { ++ ethernet1 = &rtl8153; ++ mmc0 = &sdmmc; ++ }; ++ ++ chosen { ++ stdout-path = "serial2:1500000n8"; ++ }; ++ ++ gmac_clk: gmac-clock { ++ compatible = "fixed-clock"; ++ clock-frequency = <125000000>; ++ clock-output-names = "gmac_clkin"; ++ #clock-cells = <0>; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>; ++ pinctrl-names = "default"; ++ ++ led-0 { ++ function = LED_FUNCTION_LAN; ++ color = ; ++ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ led-1 { ++ function = LED_FUNCTION_STATUS; ++ color = ; ++ gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "heartbeat"; ++ }; ++ ++ led-2 { ++ function = LED_FUNCTION_WAN; ++ color = ; ++ gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ ++ vcc_sd: sdmmc-regulator { ++ compatible = "regulator-fixed"; ++ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>; ++ pinctrl-0 = <&sdmmc0m1_pin>; ++ pinctrl-names = "default"; ++ regulator-name = "vcc_sd"; ++ regulator-boot-on; ++ vin-supply = <&vcc_io>; ++ }; ++ ++ vcc_sys: vcc-sys-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc_sys"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ }; ++ ++ vdd_5v_lan: vdd-5v-lan-regulator { ++ compatible = "regulator-fixed"; ++ enable-active-high; ++ gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>; ++ pinctrl-0 = <&lan_vdd_pin>; ++ pinctrl-names = "default"; ++ regulator-name = "vdd_5v_lan"; ++ regulator-always-on; ++ regulator-boot-on; ++ vin-supply = <&vcc_sys>; ++ }; ++}; ++ ++&cpu0 { ++ cpu-supply = <&vdd_arm>; ++}; ++ ++&cpu1 { ++ cpu-supply = <&vdd_arm>; ++}; ++ ++&cpu2 { ++ cpu-supply = <&vdd_arm>; ++}; ++ ++&cpu3 { ++ cpu-supply = <&vdd_arm>; ++}; ++ ++&display_subsystem { ++ status = "disabled"; ++}; ++ ++&gmac2io { ++ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>; ++ assigned-clock-parents = <&gmac_clk>, <&gmac_clk>; ++ clock_in_out = "input"; ++ phy-handle = <&rtl8211e>; ++ phy-mode = "rgmii"; ++ phy-supply = <&vcc_io>; ++ pinctrl-0 = <&rgmiim1_pins>; ++ pinctrl-names = "default"; ++ snps,aal; ++ rx_delay = <0x18>; ++ tx_delay = <0x24>; ++ status = "okay"; ++ ++ mdio { ++ compatible = "snps,dwmac-mdio"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ rtl8211e: ethernet-phy@1 { ++ reg = <1>; ++ pinctrl-0 = <ð_phy_reset_pin>; ++ pinctrl-names = "default"; ++ reset-assert-us = <10000>; ++ reset-deassert-us = <50000>; ++ reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++}; ++ ++&i2c1 { ++ status = "okay"; ++ ++ rk805: pmic@18 { ++ compatible = "rockchip,rk805"; ++ reg = <0x18>; ++ interrupt-parent = <&gpio1>; ++ interrupts = <24 IRQ_TYPE_LEVEL_LOW>; ++ #clock-cells = <1>; ++ clock-output-names = "xin32k", "rk805-clkout2"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ pinctrl-0 = <&pmic_int_l>; ++ pinctrl-names = "default"; ++ rockchip,system-power-controller; ++ wakeup-source; ++ ++ vcc1-supply = <&vcc_sys>; ++ vcc2-supply = <&vcc_sys>; ++ vcc3-supply = <&vcc_sys>; ++ vcc4-supply = <&vcc_sys>; ++ vcc5-supply = <&vcc_io>; ++ vcc6-supply = <&vcc_sys>; ++ ++ regulators { ++ vdd_log: DCDC_REG1 { ++ regulator-name = "vdd_log"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <712500>; ++ regulator-max-microvolt = <1450000>; ++ regulator-ramp-delay = <12500>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <1000000>; ++ }; ++ }; ++ ++ vdd_arm: DCDC_REG2 { ++ regulator-name = "vdd_arm"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <712500>; ++ regulator-max-microvolt = <1450000>; ++ regulator-ramp-delay = <12500>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <950000>; ++ }; ++ }; ++ ++ vcc_ddr: DCDC_REG3 { ++ regulator-name = "vcc_ddr"; ++ regulator-always-on; ++ regulator-boot-on; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ }; ++ }; ++ ++ vcc_io: DCDC_REG4 { ++ regulator-name = "vcc_io"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <3300000>; ++ }; ++ }; ++ ++ vcc_18: LDO_REG1 { ++ regulator-name = "vcc_18"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <1800000>; ++ }; ++ }; ++ ++ vcc18_emmc: LDO_REG2 { ++ regulator-name = "vcc18_emmc"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <1800000>; ++ }; ++ }; ++ ++ vdd_10: LDO_REG3 { ++ regulator-name = "vdd_10"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1000000>; ++ regulator-max-microvolt = <1000000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <1000000>; ++ }; ++ }; ++ }; ++ }; ++}; ++ ++&io_domains { ++ pmuio-supply = <&vcc_io>; ++ vccio1-supply = <&vcc_io>; ++ vccio2-supply = <&vcc18_emmc>; ++ vccio3-supply = <&vcc_io>; ++ vccio4-supply = <&vcc_io>; ++ vccio5-supply = <&vcc_io>; ++ vccio6-supply = <&vcc_io>; ++ status = "okay"; ++}; ++ ++&pinctrl { ++ gmac2io { ++ eth_phy_reset_pin: eth-phy-reset-pin { ++ rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>; ++ }; ++ }; ++ ++ leds { ++ lan_led_pin: lan-led-pin { ++ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ ++ sys_led_pin: sys-led-pin { ++ rockchip,pins = <3 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ ++ wan_led_pin: wan-led-pin { ++ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ }; ++ ++ lan { ++ lan_vdd_pin: lan-vdd-pin { ++ rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ }; ++ ++ pmic { ++ pmic_int_l: pmic-int-l { ++ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>; ++ }; ++ }; ++}; ++ ++&pwm2 { ++ status = "okay"; ++}; ++ ++&sdmmc { ++ bus-width = <4>; ++ cap-sd-highspeed; ++ disable-wp; ++ pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>; ++ pinctrl-names = "default"; ++ vmmc-supply = <&vcc_sd>; ++ status = "okay"; ++}; ++ ++&spi0 { ++ status = "okay"; ++ ++ flash@0 { ++ compatible = "jedec,spi-nor"; ++ reg = <0>; ++ spi-max-frequency = <50000000>; ++ }; ++}; ++ ++&tsadc { ++ rockchip,hw-tshut-mode = <0>; ++ rockchip,hw-tshut-polarity = <0>; ++ status = "okay"; ++}; ++ ++&u2phy { ++ status = "okay"; ++}; ++ ++&u2phy_host { ++ status = "okay"; ++}; ++ ++&u2phy_otg { ++ status = "okay"; ++}; ++ ++&uart2 { ++ status = "okay"; ++}; ++ ++&usb20_otg { ++ dr_mode = "host"; ++ status = "okay"; ++}; ++ ++&usbdrd3 { ++ dr_mode = "host"; ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ /* Second port is for USB 3.0 */ ++ rtl8153: device@2 { ++ compatible = "usbbda,8153"; ++ reg = <2>; ++ }; ++}; ++ ++&usb_host0_ehci { ++ status = "okay"; ++}; ++ ++&usb_host0_ohci { ++ status = "okay"; ++}; diff --git a/target/linux/rockchip/patches-6.1/107-arm64-dts-rockchip-Update-LED-properties-for-Orange-.patch b/target/linux/rockchip/patches-6.1/107-arm64-dts-rockchip-Update-LED-properties-for-Orange-.patch new file mode 100644 index 0000000000..b1e26d4e3e --- /dev/null +++ b/target/linux/rockchip/patches-6.1/107-arm64-dts-rockchip-Update-LED-properties-for-Orange-.patch @@ -0,0 +1,56 @@ +From d2166e3b3680bd2b206aebf1e1ce4c0d346f3c50 Mon Sep 17 00:00:00 2001 +From: Tianling Shen +Date: Fri, 19 May 2023 12:10:52 +0800 +Subject: [PATCH] arm64: dts: rockchip: Update LED properties for Orange Pi R1 + Plus + +Add OpenWrt's LED aliases for showing system status. +Also replace function/color with legacy label as OpenWrt relys on it +to update LED settings. + +Signed-off-by: Tianling Shen +--- + .../dts/rockchip/rk3328-orangepi-r1-plus.dts | 17 +++++++++-------- + 1 file changed, 9 insertions(+), 8 deletions(-) + +--- a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts ++++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts +@@ -17,6 +17,11 @@ + aliases { + ethernet1 = &rtl8153; + mmc0 = &sdmmc; ++ ++ led-boot = &status_led; ++ led-failsafe = &status_led; ++ led-running = &status_led; ++ led-upgrade = &status_led; + }; + + chosen { +@@ -36,22 +41,18 @@ + pinctrl-names = "default"; + + led-0 { +- function = LED_FUNCTION_LAN; +- color = ; + gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>; ++ label = "green:lan"; + }; + +- led-1 { +- function = LED_FUNCTION_STATUS; +- color = ; ++ status_led: led-1 { + gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>; +- linux,default-trigger = "heartbeat"; ++ label = "red:status"; + }; + + led-2 { +- function = LED_FUNCTION_WAN; +- color = ; + gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>; ++ label = "green:wan"; + }; + }; + diff --git a/target/linux/rockchip/patches-6.1/108-arm64-dts-rockchip-add-LED-configuration-to-Orange-P.patch b/target/linux/rockchip/patches-6.1/108-arm64-dts-rockchip-add-LED-configuration-to-Orange-P.patch new file mode 100644 index 0000000000..37b59925fc --- /dev/null +++ b/target/linux/rockchip/patches-6.1/108-arm64-dts-rockchip-add-LED-configuration-to-Orange-P.patch @@ -0,0 +1,24 @@ +From b46a530d12ada422b9d5b2b97059e0d3ed950b40 Mon Sep 17 00:00:00 2001 +From: Tianling Shen +Date: Fri, 19 May 2023 12:38:04 +0800 +Subject: [PATCH] arm64: dts: rockchip: add LED configuration to Orange Pi R1 + Plus + +Add the correct value for the RTL8153 LED configuration register to +match the blink behavior of the other port on the device. + +Signed-off-by: Tianling Shen +--- + arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts | 1 + + 1 file changed, 1 insertion(+) + +--- a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts ++++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts +@@ -362,6 +362,7 @@ + rtl8153: device@2 { + compatible = "usbbda,8153"; + reg = <2>; ++ realtek,led-data = <0x87>; + }; + }; +