From: Sebastian Quilitz Date: Wed, 23 Nov 2016 17:51:15 +0000 (+0100) Subject: ipq806x: add support for TP-Link Archer VR2600v X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=ae79c41286f0d9a97f2641450240ecac5465677d;p=openwrt%2Fstaging%2Fyousong.git ipq806x: add support for TP-Link Archer VR2600v This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz --- diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index e4dc820a5e..6570b783a4 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -45,6 +45,13 @@ nbg6817) ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:amber:wifi5" "phy0radio" ucidef_set_led_netdev "wan" "WAN" "$board:white:internet" "eth1" ;; +vr2600v) + ucidef_set_led_usbport "usb" "USB" "${board}:white:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1" + ucidef_set_led_switch "lan" "lan" "${board}:white:lan" "switch0" "0x1e" + ucidef_set_led_wlan "wlan2g" "WLAN2G" "${board}:white:wlan2g" "phy0radio" + ucidef_set_led_wlan "wlan5g" "WLAN5G" "${board}:white:wlan5g" "phy1radio" + ucidef_set_led_switch "wan" "wan" "${board}:white:wan" "switch0" "0x20" + ;; *) ;; esac diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index a461033dfe..8417f0e9b7 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -18,7 +18,8 @@ c2600 |\ d7800 |\ r7500 |\ r7500v2 |\ -r7800) +r7800 |\ +vr2600v) ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0" ;; diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index f95692a889..625f77f797 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -63,6 +63,9 @@ case "$FIRMWARE" in r7800) ath10kcal_extract "art" 4096 12064 ;; + vr2600v) + ath10kcal_extract "ART" 4096 12064 + ;; esac ;; "ath10k/cal-pci-0001:01:00.0.bin") @@ -82,6 +85,9 @@ case "$FIRMWARE" in r7800) ath10kcal_extract "art" 20480 12064 ;; + vr2600v) + ath10kcal_extract "ART" 20480 12064 + ;; esac ;; *) diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 8a0579b747..3482a09b70 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -21,6 +21,9 @@ case "$board" in r7800) echo $(macaddr_add $(mtd_get_mac_binary art 6) $(($PHYNBR + 1)) ) > /sys${DEVPATH}/macaddress ;; + vr2600v) + echo $(macaddr_add $(mtd_get_mac_binary default-mac 0) $(($PHYNBR - 1)) ) > /sys${DEVPATH}/macaddress + ;; *) ;; esac diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh index 1bd0e2bd94..a8b909ac04 100644 --- a/target/linux/ipq806x/base-files/lib/ipq806x.sh +++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh @@ -41,6 +41,9 @@ ipq806x_board_detect() { *"R7800") name="r7800" ;; + *"VR2600v") + name="vr2600v" + ;; esac [ -z "$name" ] && name="unknown" diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 250979dcf0..c3741f9ff2 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -37,6 +37,11 @@ platform_do_upgrade() { ea8500) platform_do_upgrade_linksys "$ARGV" ;; + vr2600v) + PART_NAME="kernel:rootfs" + MTD_CONFIG_ARGS="-s 0x200000" + default_do_upgrade "$ARGV" + ;; esac } diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts new file mode 100644 index 0000000000..e03adc1483 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts @@ -0,0 +1,423 @@ +#include "qcom-ipq8064-v1.0.dtsi" + +#include + +/ { + model = "TP-Link Archer VR2600v"; + compatible = "tplink,vr2600v", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + serial0 = &uart4; + mdio-gpio0 = &mdio0; + + led-boot = &power; + led-failsafe = &general; + led-running = &power; + led-upgrade = &general; + }; + + chosen { + linux,stdout-path = "serial0:115200n8"; + }; + + soc { + pinmux@800000 { + led_pins: led_pins { + pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17", + "gpio26", "gpio53", "gpio56", "gpio66"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + + i2c4_pins: i2c4_pinmux { + mux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + drive-strength = <12>; + bias-disable; + }; + }; + + button_pins: button_pins { + pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + }; + + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + + cs { + pins = "gpio20"; + drive-strength = <10>; + bias-pull-up; + }; + + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; + + }; + + gsbi@16300000 { + qcom,mode = ; + status = "ok"; + serial@16340000 { + status = "ok"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ + }; + + gsbi5: gsbi@1a200000 { + qcom,mode = ; + status = "ok"; + + spi4: spi@1a280000 { + status = "ok"; + spi-max-frequency = <50000000>; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + flash: W25Q128@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x20000>; + read-only; + }; + + MIBIB@20000 { + label = "MIBIB"; + reg = <0x20000 0x20000>; + read-only; + }; + + SBL2@40000 { + label = "SBL2"; + reg = <0x40000 0x40000>; + read-only; + }; + + SBL3@80000 { + label = "SBL3"; + reg = <0x80000 0x80000>; + read-only; + }; + + DDRCONFIG@100000 { + label = "DDRCONFIG"; + reg = <0x100000 0x10000>; + read-only; + }; + + SSD@110000 { + label = "SSD"; + reg = <0x110000 0x10000>; + read-only; + }; + + TZ@120000 { + label = "TZ"; + reg = <0x120000 0x80000>; + read-only; + }; + + RPM@1a0000 { + label = "RPM"; + reg = <0x1a0000 0x80000>; + read-only; + }; + + APPSBL@220000 { + label = "APPSBL"; + reg = <0x220000 0x80000>; + read-only; + }; + + APPSBLENV@2a0000 { + label = "APPSBLENV"; + reg = <0x2a0000 0x40000>; + read-only; + }; + + OLDART@2e0000 { + label = "OLDART"; + reg = <0x2e0000 0x40000>; + read-only; + }; + + kernel@320000 { + label = "kernel"; + reg = <0x320000 0x200000>; + }; + + rootfs@520000 { + label = "rootfs"; + reg = <0x520000 0xa60000>; + }; + + defaultmac: default-mac@0xfaf100 { + label = "default-mac"; + reg = <0xfaf100 0x00200>; + read-only; + }; + + ART@fc0000 { + label = "ART"; + reg = <0xfc0000 0x40000>; + read-only; + }; + + }; + }; + }; + + phy@100f8800 { /* USB3 port 1 HS phy */ + status = "ok"; + }; + + phy@100f8830 { /* USB3 port 1 SS phy */ + status = "ok"; + }; + + phy@110f8800 { /* USB3 port 0 HS phy */ + status = "ok"; + }; + + phy@110f8830 { /* USB3 port 0 SS phy */ + status = "ok"; + }; + + usb30@0 { + status = "ok"; + }; + + usb30@1 { + status = "ok"; + }; + + pcie0: pci@1b500000 { + status = "ok"; + phy-tx0-term-offset = <7>; + }; + + pcie1: pci@1b700000 { + status = "ok"; + phy-tx0-term-offset = <7>; + }; + + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + device_type = "ethernet-phy"; + reg = <4>; + }; + }; + + gmac1: ethernet@37200000 { + status = "ok"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&defaultmac 0>; + mtd-mac-address-increment = <1>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + gmac2: ethernet@37400000 { + status = "ok"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&defaultmac 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + rpm@108000 { + pinctrl-0 = <&i2c4_pins>; + pinctrl-names = "default"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + dect { + label = "dect"; + gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + ledswitch { + label = "ledswitch"; + gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + dsl { + label = "vr2600v:white:dsl"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + }; + + usb { + label = "vr2600v:white:usb"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + lan { + label = "vr2600v:white:lan"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + wlan2g { + label = "vr2600v:white:wlan2g"; + gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; + }; + + wlan5g { + label = "vr2600v:white:wlan5g"; + gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>; + }; + + power: power { + label = "vr2600v:white:power"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; + }; + + phone { + label = "vr2600v:white:phone"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + }; + + wan { + label = "vr2600v:white:wan"; + gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; + }; + + general: general { + label = "vr2600v:white:general"; + gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&adm_dma { + status = "ok"; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index 47c28ab651..3cc48bb905 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -224,6 +224,23 @@ define Device/NBG6817 $(call Device/ZyXELImage) endef -TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817 +define Device/VR2600v + PROFILES += $$(DEVICE_NAME) + FILESYSTEMS := squashfs + KERNEL_SUFFIX := -uImage + KERNEL = kernel-bin | append-dtb | uImage none + KERNEL_NAME := zImage + KERNEL_SIZE := 2097152 + DEVICE_DTS := qcom-ipq8064-vr2600v + BLOCKSIZE := 128k + PAGESIZE := 2048 + BOARD_NAME := vr2600v + DEVICE_TITLE := TP-Link Archer VR2600v + DEVICE_PACKAGES := ath10k-firmware-qca99x0 + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata +endef + +TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817 VR2600v $(eval $(call BuildImage))