From: Henryk Heisig Date: Fri, 16 Jun 2017 13:26:30 +0000 (+0200) Subject: ar71xx: add support for TP-Link Archer C58 v1 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=b05c7193fd289ff697324caccf77adf9ffa76373;p=openwrt%2Fstaging%2Fjogo.git ar71xx: add support for TP-Link Archer C58 v1 TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 6x LED, 3x button - UART header on PCB, RX, TX at TP4+5 (backside) QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to patch macaddress. Flash instruction: Use "factory" image directly in vendor GUI. Recovery method: 1. Set PC to fixed ip address 192.168.0.66/24. 2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and rename it to "tp_recovery.bin". 3. Start a tftp server with the file "tp_recovery.bin" in its root directory. 4. Turn off the router. 5. Press and hold Reset button. 6. Turn on router with the reset button pressed and wait ~15 seconds. 7. Release the reset button and after a short time the firmware should be transferred from the tftp server. 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin erase 0x9f020000 +$filesize cp.b $fileaddr 0x9f020000 $filesize reset This commit is based on GitHub PR#1112 Signed-off-by: Henryk Heisig --- diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index d80efefc34..de9072e55c 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -63,6 +63,7 @@ archer-c25-v1) ucidef_set_led_switch "lan3" "LAN3" "$board:green:lan3" "switch0" "0x04" ucidef_set_led_switch "lan4" "LAN4" "$board:green:lan4" "switch0" "0x02" ;; +archer-c58-v1|\ archer-c59-v1|\ archer-c60-v1) ucidef_set_led_switch "lan" "LAN" "$board:green:lan" "switch0" "0x1E" diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network index a7a9921faf..311e091da7 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/02_network +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network @@ -217,6 +217,7 @@ ar71xx_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan" ;; + archer-c58-v1|\ archer-c59-v1|\ rb-450g) ucidef_set_interfaces_lan_wan "eth1.1" "eth0" diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index 0bb338a573..2d2a6788a7 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -52,6 +52,7 @@ get_status_led() { status_led="ap135:green:status" ;; archer-c25-v1|\ + archer-c58-v1|\ archer-c59-v1|\ archer-c60-v1|\ fritz300e|\ diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 91db049c44..ecbc9b8163 100644 --- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -134,6 +134,13 @@ case "$FIRMWARE" in ;; esac ;; +"ath10k/pre-cal-pci-0000:00:00.0.bin") + case $board in + archer-c58-v1) + ath10kcal_extract "art" 20480 12064 + ;; + esac + ;; *) exit 1 ;; diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ar71xx/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac new file mode 100644 index 0000000000..7d2eca546d --- /dev/null +++ b/target/linux/ar71xx/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -0,0 +1,21 @@ +#!/bin/ash + +[ "$ACTION" == "add" ] || exit 0 + +PHYNBR=${DEVPATH##*/phy} + +[ -n $PHYNBR ] || exit 0 + +. /lib/ar71xx.sh +. /lib/functions/system.sh + +board=$(ar71xx_board_name) + +case "$board" in + archer-c58-v1) + echo $(macaddr_add $(mtd_get_mac_binary mac 8) $(($PHYNBR - 1)) ) > /sys${DEVPATH}/macaddress + ;; + *) + ;; +esac + diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh index 3f781a8e5c..df8c6d7283 100755 --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh @@ -449,6 +449,9 @@ ar71xx_board_detect() { *"Archer C5") name="archer-c5" ;; + *"Archer C58 v1") + name="archer-c58-v1" + ;; *"Archer C59 v1") name="archer-c59-v1" ;; diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh index 454af2c3e6..85fc1e9122 100755 --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh @@ -207,6 +207,7 @@ platform_check_image() { ap531b0|\ ap90q|\ archer-c25-v1|\ + archer-c58-v1|\ archer-c59-v1|\ archer-c60-v1|\ bullet-m|\ diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4 index 8be13e16cd..6abd7a4021 100644 --- a/target/linux/ar71xx/config-4.4 +++ b/target/linux/ar71xx/config-4.4 @@ -52,6 +52,7 @@ CONFIG_ATH79_MACH_AP531B0=y CONFIG_ATH79_MACH_AP90Q=y CONFIG_ATH79_MACH_AP96=y CONFIG_ATH79_MACH_ARCHER_C25_V1=y +CONFIG_ATH79_MACH_ARCHER_C58_V1=y CONFIG_ATH79_MACH_ARCHER_C59_V1=y CONFIG_ATH79_MACH_ARCHER_C60_V1=y CONFIG_ATH79_MACH_ARCHER_C7=y diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt index 0ae9a11ff6..0584e3896b 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt @@ -1328,6 +1328,16 @@ config ATH79_MACH_ARCHER_C25_V1 select ATH79_DEV_M25P80 select ATH79_DEV_WMAC +config ATH79_MACH_ARCHER_C58_V1 + bool "TP-LINK Archer C58 v1 support" + select SOC_QCA956X + select ATH79_DEV_AP9X_PCI if PCI + select ATH79_DEV_ETH + select ATH79_DEV_GPIO_BUTTONS + select ATH79_DEV_LEDS_GPIO + select ATH79_DEV_M25P80 + select ATH79_DEV_WMAC + config ATH79_MACH_ARCHER_C59_V1 bool "TP-LINK Archer C59 v1 support" select SOC_QCA956X diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile index 869920ca30..dd0b729996 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile @@ -57,6 +57,7 @@ obj-$(CONFIG_ATH79_MACH_AP531B0) += mach-ap531b0.o obj-$(CONFIG_ATH79_MACH_AP90Q) += mach-ap90q.o obj-$(CONFIG_ATH79_MACH_AP96) += mach-ap96.o obj-$(CONFIG_ATH79_MACH_ARCHER_C25_V1) += mach-archer-c25-v1.o +obj-$(CONFIG_ATH79_MACH_ARCHER_C58_V1) += mach-archer-c59-v1.o obj-$(CONFIG_ATH79_MACH_ARCHER_C59_V1) += mach-archer-c59-v1.o obj-$(CONFIG_ATH79_MACH_ARCHER_C60_V1) += mach-archer-c60-v1.o obj-$(CONFIG_ATH79_MACH_ARCHER_C7) += mach-archer-c7.o diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-archer-c59-v1.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-archer-c59-v1.c index d55f9b9f75..f385d4a5a3 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/mach-archer-c59-v1.c +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-archer-c59-v1.c @@ -1,7 +1,7 @@ /* - * TP-Link Archer C59 v1 board support + * TP-Link Archer C58/C59 v1 board support * - * Copyright (C) 2016 Henryk Heisig + * Copyright (C) 2017 Henryk Heisig * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License version 2 as published @@ -65,6 +65,44 @@ #define ARCHER_C59_V1_WMAC_CALDATA_OFFSET 0x1000 #define ARCHER_C59_V1_PCI_CALDATA_OFFSET 0x5000 +static struct gpio_led archer_c58_v1_leds_gpio[] __initdata = { + { + .name = "archer-c58-v1:green:power", + .gpio = ARCHER_C59_74HC_GPIO_LED_POWER, + .active_low = 1, + }, + { + .name = "archer-c58-v1:green:wlan2g", + .gpio = ARCHER_C59_74HC_GPIO_LED_WLAN2, + .active_low = 1, + }, + { + .name = "archer-c58-v1:green:wlan5g", + .gpio = ARCHER_C59_74HC_GPIO_LED_WLAN5, + .active_low = 1, + }, + { + .name = "archer-c58-v1:green:lan", + .gpio = ARCHER_C59_74HC_GPIO_LED_LAN, + .active_low = 1, + }, + { + .name = "archer-c58-v1:green:wan", + .gpio = ARCHER_C59_74HC_GPIO_LED_WAN_GREEN, + .active_low = 1, + }, + { + .name = "archer-c58-v1:amber:wan", + .gpio = ARCHER_C59_74HC_GPIO_LED_WAN_AMBER, + .active_low = 1, + }, + { + .name = "archer-c58-v1:green:wps", + .gpio = ARCHER_C59_74HC_GPIO_LED_WPS, + .active_low = 1, + }, +}; + static struct gpio_led archer_c59_v1_leds_gpio[] __initdata = { { .name = "archer-c59-v1:green:power", @@ -177,7 +215,7 @@ static struct spi_board_info archer_c59_v1_spi_info[] = { }, }; -static void __init archer_c59_v1_setup(void) +static void __init archer_c5x_v1_setup(void) { u8 *mac = (u8 *) KSEG1ADDR(0x1f010008); u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); @@ -187,9 +225,6 @@ static void __init archer_c59_v1_setup(void) ARRAY_SIZE(archer_c59_v1_spi_info)); platform_device_register(&archer_c59_v1_spi_device); - ath79_register_leds_gpio(-1, ARRAY_SIZE(archer_c59_v1_leds_gpio), - archer_c59_v1_leds_gpio); - ath79_register_gpio_keys_polled(-1, ARCHER_C59_V1_KEYS_POLL_INTERVAL, ARRAY_SIZE(archer_c59_v1_gpio_keys), archer_c59_v1_gpio_keys); @@ -233,5 +268,22 @@ static void __init archer_c59_v1_setup(void) "LED reset"); } +static void __init archer_c58_v1_setup(void) +{ + archer_c5x_v1_setup(); + ath79_register_leds_gpio(-1, ARRAY_SIZE(archer_c58_v1_leds_gpio), + archer_c58_v1_leds_gpio); +} + +MIPS_MACHINE(ATH79_MACH_ARCHER_C58_V1, "ARCHER-C58-V1", + "TP-LINK Archer C58 v1", archer_c58_v1_setup); + +static void __init archer_c59_v1_setup(void) +{ + archer_c5x_v1_setup(); + ath79_register_leds_gpio(-1, ARRAY_SIZE(archer_c59_v1_leds_gpio), + archer_c59_v1_leds_gpio); +} + MIPS_MACHINE(ATH79_MACH_ARCHER_C59_V1, "ARCHER-C59-V1", "TP-LINK Archer C59 v1", archer_c59_v1_setup); diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h index 618abfb1dc..dde6d9735a 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h @@ -42,6 +42,7 @@ enum ath79_mach_type { ATH79_MACH_AP96, /* Atheros AP96 */ ATH79_MACH_ARCHER_C25_V1, /* TP-LINK Archer C25 V1 board */ ATH79_MACH_ARCHER_C5, /* TP-LINK Archer C5 board */ + ATH79_MACH_ARCHER_C58_V1, /* TP-LINK Archer C58 V1 board */ ATH79_MACH_ARCHER_C59_V1, /* TP-LINK Archer C59 V1 board */ ATH79_MACH_ARCHER_C60_V1, /* TP-LINK Archer C60 V1 board */ ATH79_MACH_ARCHER_C7, /* TP-LINK Archer C7 board */ diff --git a/target/linux/ar71xx/image/tp-link.mk b/target/linux/ar71xx/image/tp-link.mk index 243c15a858..0979505a78 100644 --- a/target/linux/ar71xx/image/tp-link.mk +++ b/target/linux/ar71xx/image/tp-link.mk @@ -137,6 +137,17 @@ define Device/archer-c25-v1 MTDPARTS := spi0.0:128k(factory-uboot)ro,64k(u-boot)ro,1536k(kernel),6272k(rootfs),128k(config)ro,64k(art)ro,7808k@0x30000(firmware) endef +define Device/archer-c58-v1 + $(Device/archer-cxx) + DEVICE_TITLE := TP-LINK Archer C58 v1 + DEVICE_PACKAGES := kmod-ath10k + BOARDNAME := ARCHER-C58-V1 + TPLINK_BOARD_NAME := ARCHER-C58-V1 + DEVICE_PROFILE := ARCHERC58V1 + IMAGE_SIZE := 7936k + MTDPARTS := spi0.0:64k(u-boot)ro,64k(mac)ro,1344k(kernel),6592k(rootfs),64k(tplink)ro,64k(art)ro,7936k@0x20000(firmware) +endef + define Device/archer-c59-v1 $(Device/archer-cxx) DEVICE_TITLE := TP-LINK Archer C59 v1 @@ -158,7 +169,7 @@ define Device/archer-c60-v1 IMAGE_SIZE := 7936k MTDPARTS := spi0.0:64k(u-boot)ro,64k(mac)ro,1344k(kernel),6592k(rootfs),64k(tplink)ro,64k(art)ro,7936k@0x20000(firmware) endef -TARGET_DEVICES += archer-c25-v1 archer-c59-v1 archer-c60-v1 +TARGET_DEVICES += archer-c25-v1 archer-c58-v1 archer-c59-v1 archer-c60-v1 define Device/archer-c5-v1 $(Device/tplink-16mlzma) diff --git a/target/linux/ar71xx/mikrotik/config-default b/target/linux/ar71xx/mikrotik/config-default index 6b87871b9a..ac9ba1bd28 100644 --- a/target/linux/ar71xx/mikrotik/config-default +++ b/target/linux/ar71xx/mikrotik/config-default @@ -17,6 +17,7 @@ # CONFIG_ATH79_MACH_AP90Q is not set # CONFIG_ATH79_MACH_AP96 is not set # CONFIG_ATH79_MACH_ARCHER_C25_V1 is not set +# CONFIG_ATH79_MACH_ARCHER_C58_V1 is not set # CONFIG_ATH79_MACH_ARCHER_C59_V1 is not set # CONFIG_ATH79_MACH_ARCHER_C60_V1 is not set # CONFIG_ATH79_MACH_ARCHER_C7 is not set diff --git a/target/linux/ar71xx/nand/config-default b/target/linux/ar71xx/nand/config-default index 0e1827663a..9a96830fbd 100644 --- a/target/linux/ar71xx/nand/config-default +++ b/target/linux/ar71xx/nand/config-default @@ -17,6 +17,7 @@ # CONFIG_ATH79_MACH_AP90Q is not set # CONFIG_ATH79_MACH_AP96 is not set # CONFIG_ATH79_MACH_ARCHER_C25_V1 is not set +# CONFIG_ATH79_MACH_ARCHER_C58_V1 is not set # CONFIG_ATH79_MACH_ARCHER_C59_V1 is not set # CONFIG_ATH79_MACH_ARCHER_C60_V1 is not set # CONFIG_ATH79_MACH_ARCHER_C7 is not set diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index 83bbd23b76..cc5b583f7c 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -341,6 +341,41 @@ static struct device_info boards[] = { .last_sysupgrade_partition = "file-system", }, + /** Firmware layout for the C58v1 */ + { + .id = "ARCHER-C58-V1", + .vendor = "", + .support_list = + "SupportList:\r\n" + "{product_name:Archer C58,product_ver:1.0.0,special_id:00000000}\r\n" + "{product_name:Archer C58,product_ver:1.0.0,special_id:45550000}\r\n" + "{product_name:Archer C58,product_ver:1.0.0,special_id:55530000}\r\n", + .support_trail = '\x00', + .soft_ver = "soft_ver:1.0.0\n", + + .partitions = { + {"fs-uboot", 0x00000, 0x10000}, + {"default-mac", 0x10000, 0x00200}, + {"pin", 0x10200, 0x00200}, + {"product-info", 0x10400, 0x00100}, + {"partition-table", 0x10500, 0x00800}, + {"soft-version", 0x11300, 0x00200}, + {"support-list", 0x11500, 0x00100}, + {"device-id", 0x11600, 0x00100}, + {"profile", 0x11700, 0x03900}, + {"default-config", 0x15000, 0x04000}, + {"user-config", 0x19000, 0x04000}, + {"os-image", 0x20000, 0x150000}, + {"file-system", 0x170000, 0x678000}, + {"certyficate", 0x7e8000, 0x08000}, + {"radio", 0x7f0000, 0x10000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "file-system", + }, + /** Firmware layout for the C59v1 */ { .id = "ARCHER-C59-V1",