From: Chukun Pan Date: Thu, 15 Jun 2023 15:21:40 +0000 (+0800) Subject: uboot-mediatek: add JCG Q30 PRO support X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=b42c5272286ee248c698cc2cfac88df1bf51cbe3;p=openwrt%2Fstaging%2F981213.git uboot-mediatek: add JCG Q30 PRO support The vendor uboot will verify firmware at boot. So add a custom uboot build for this device. Signed-off-by: Chukun Pan --- diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic index d4d0969b7a..5cd63a46e6 100644 --- a/package/boot/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-envtools/files/mediatek_filogic @@ -79,6 +79,7 @@ xiaomi,redmi-router-ax6000-stock) ubootenv_add_uci_sys_config "/dev/mtd2" "0x0" "0x10000" "0x20000" ;; h3c,magic-nx30-pro|\ +jcg,q30-pro|\ qihoo,360t7|\ tplink,tl-xdr4288|\ tplink,tl-xdr6086|\ diff --git a/package/boot/uboot-mediatek/Makefile b/package/boot/uboot-mediatek/Makefile index ad25d051fe..a06d323bae 100644 --- a/package/boot/uboot-mediatek/Makefile +++ b/package/boot/uboot-mediatek/Makefile @@ -236,6 +236,18 @@ define U-Boot/mt7981_h3c_magic-nx30-pro DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3 endef +define U-Boot/mt7981_jcg_q30-pro + NAME:=JCG Q30 PRO + BUILD_SUBTARGET:=filogic + BUILD_DEVICES:=jcg_q30-pro + UBOOT_CONFIG:=mt7981_jcg_q30-pro + UBOOT_IMAGE:=u-boot.fip + BL2_BOOTDEV:=spim-nand + BL2_SOC:=mt7981 + BL2_DDRTYPE:=ddr3 + DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3 +endef + define U-Boot/mt7981_rfb-spim-nand NAME:=MT7981 Reference Board BUILD_SUBTARGET:=filogic @@ -523,6 +535,7 @@ UBOOT_TARGETS := \ mt7981_cmcc_rax3000m-emmc \ mt7981_cmcc_rax3000m-nand \ mt7981_h3c_magic-nx30-pro \ + mt7981_jcg_q30-pro \ mt7981_rfb-spim-nand \ mt7981_rfb-emmc \ mt7981_rfb-nor \ diff --git a/package/boot/uboot-mediatek/patches/438-add-jcg_q30-pro.patch b/package/boot/uboot-mediatek/patches/438-add-jcg_q30-pro.patch new file mode 100644 index 0000000000..639cae174e --- /dev/null +++ b/package/boot/uboot-mediatek/patches/438-add-jcg_q30-pro.patch @@ -0,0 +1,420 @@ +--- /dev/null ++++ b/configs/mt7981_jcg_q30-pro_defconfig +@@ -0,0 +1,175 @@ ++CONFIG_ARM=y ++CONFIG_POSITION_INDEPENDENT=y ++CONFIG_ARCH_MEDIATEK=y ++CONFIG_TARGET_MT7981=y ++CONFIG_TEXT_BASE=0x41e00000 ++CONFIG_SYS_MALLOC_F_LEN=0x4000 ++CONFIG_SYS_HAS_NONCACHED_MEMORY=y ++CONFIG_NR_DRAM_BANKS=1 ++CONFIG_DEFAULT_DEVICE_TREE="mt7981_jcg_q30-pro" ++CONFIG_DEFAULT_ENV_FILE="jcg_q30-pro_env" ++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7981_jcg_q30-pro.dtb" ++CONFIG_OF_LIBFDT_OVERLAY=y ++CONFIG_DEBUG_UART_BASE=0x11002000 ++CONFIG_DEBUG_UART_CLOCK=40000000 ++CONFIG_DEBUG_UART=y ++CONFIG_SYS_LOAD_ADDR=0x46000000 ++CONFIG_SMBIOS_PRODUCT_NAME="" ++CONFIG_AUTOBOOT_KEYED=y ++CONFIG_BOOTDELAY=30 ++CONFIG_AUTOBOOT_MENU_SHOW=y ++CONFIG_CFB_CONSOLE_ANSI=y ++CONFIG_BOARD_LATE_INIT=y ++CONFIG_BUTTON=y ++CONFIG_BUTTON_GPIO=y ++CONFIG_GPIO_HOG=y ++CONFIG_CMD_ENV_FLAGS=y ++CONFIG_FIT=y ++CONFIG_FIT_ENABLE_SHA256_SUPPORT=y ++CONFIG_LED=y ++CONFIG_LED_BLINK=y ++CONFIG_LED_GPIO=y ++CONFIG_LOGLEVEL=7 ++CONFIG_LOG=y ++CONFIG_SYS_PROMPT="MT7981> " ++CONFIG_CMD_BOOTMENU=y ++CONFIG_CMD_BOOTP=y ++CONFIG_CMD_BUTTON=y ++CONFIG_CMD_CACHE=y ++CONFIG_CMD_CDP=y ++CONFIG_CMD_CPU=y ++CONFIG_CMD_DHCP=y ++CONFIG_CMD_DM=y ++CONFIG_CMD_DNS=y ++CONFIG_CMD_ECHO=y ++CONFIG_CMD_ENV_READMEM=y ++CONFIG_CMD_ERASEENV=y ++CONFIG_CMD_EXT4=y ++CONFIG_CMD_FAT=y ++CONFIG_CMD_FDT=y ++CONFIG_CMD_FS_GENERIC=y ++CONFIG_CMD_FS_UUID=y ++CONFIG_CMD_GPIO=y ++CONFIG_CMD_GPT=y ++CONFIG_CMD_HASH=y ++CONFIG_CMD_ITEST=y ++CONFIG_CMD_LED=y ++CONFIG_CMD_LICENSE=y ++CONFIG_CMD_LINK_LOCAL=y ++# CONFIG_CMD_MBR is not set ++CONFIG_CMD_PCI=y ++CONFIG_CMD_PSTORE=y ++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000 ++CONFIG_CMD_SF_TEST=y ++CONFIG_CMD_PING=y ++CONFIG_CMD_PXE=y ++CONFIG_CMD_PWM=y ++CONFIG_CMD_SMC=y ++CONFIG_CMD_TFTPBOOT=y ++CONFIG_CMD_TFTPSRV=y ++CONFIG_CMD_UBI=y ++CONFIG_CMD_UBI_RENAME=y ++CONFIG_CMD_UBIFS=y ++CONFIG_CMD_ASKENV=y ++CONFIG_CMD_PART=y ++CONFIG_CMD_RARP=y ++CONFIG_CMD_SETEXPR=y ++CONFIG_CMD_SLEEP=y ++CONFIG_CMD_SNTP=y ++CONFIG_CMD_SOURCE=y ++CONFIG_CMD_STRINGS=y ++CONFIG_CMD_UUID=y ++CONFIG_DISPLAY_CPUINFO=y ++CONFIG_DM_MTD=y ++CONFIG_DM_REGULATOR=y ++CONFIG_DM_REGULATOR_FIXED=y ++CONFIG_DM_REGULATOR_GPIO=y ++CONFIG_DM_PWM=y ++CONFIG_PWM_MTK=y ++CONFIG_HUSH_PARSER=y ++CONFIG_SYS_REDUNDAND_ENVIRONMENT=y ++CONFIG_SYS_RELOC_GD_ENV_ADDR=y ++CONFIG_VERSION_VARIABLE=y ++CONFIG_PARTITION_UUIDS=y ++CONFIG_NETCONSOLE=y ++CONFIG_REGMAP=y ++CONFIG_SYSCON=y ++CONFIG_CLK=y ++CONFIG_DM_GPIO=y ++CONFIG_DM_SCSI=y ++CONFIG_AHCI=y ++CONFIG_AHCI_PCI=y ++CONFIG_SCSI_AHCI=y ++CONFIG_SCSI=y ++CONFIG_CMD_SCSI=y ++CONFIG_PHY=y ++CONFIG_PHY_MTK_TPHY=y ++CONFIG_PHY_FIXED=y ++CONFIG_MTK_AHCI=y ++CONFIG_DM_ETH=y ++CONFIG_MEDIATEK_ETH=y ++CONFIG_PCI=y ++# CONFIG_MMC is not set ++# CONFIG_DM_MMC is not set ++CONFIG_MTD=y ++CONFIG_MTD_UBI_FASTMAP=y ++CONFIG_DM_PCI=y ++CONFIG_PCIE_MEDIATEK=y ++CONFIG_PINCTRL=y ++CONFIG_PINCONF=y ++CONFIG_PINCTRL_MT7622=y ++CONFIG_POWER_DOMAIN=y ++CONFIG_PRE_CONSOLE_BUFFER=y ++CONFIG_PRE_CON_BUF_ADDR=0x4007EF00 ++CONFIG_MTK_POWER_DOMAIN=y ++CONFIG_RAM=y ++CONFIG_DM_SERIAL=y ++CONFIG_MTK_SERIAL=y ++CONFIG_SPI=y ++CONFIG_DM_SPI=y ++CONFIG_MTK_SPI_NAND=y ++CONFIG_MTK_SPI_NAND_MTD=y ++CONFIG_SYSRESET_WATCHDOG=y ++CONFIG_WDT_MTK=y ++CONFIG_LZO=y ++CONFIG_ZSTD=y ++CONFIG_HEXDUMP=y ++CONFIG_RANDOM_UUID=y ++CONFIG_REGEX=y ++CONFIG_OF_EMBED=y ++CONFIG_ENV_OVERWRITE=y ++CONFIG_ENV_IS_IN_UBI=y ++CONFIG_ENV_UBI_PART="ubi" ++CONFIG_ENV_SIZE=0x1f000 ++CONFIG_ENV_SIZE_REDUND=0x1f000 ++CONFIG_ENV_UBI_VOLUME="ubootenv" ++CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2" ++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y ++CONFIG_NET_RANDOM_ETHADDR=y ++CONFIG_REGMAP=y ++CONFIG_SYSCON=y ++CONFIG_CLK=y ++CONFIG_PHY_FIXED=y ++CONFIG_DM_ETH=y ++CONFIG_MEDIATEK_ETH=y ++CONFIG_PINCTRL=y ++CONFIG_PINCONF=y ++CONFIG_PINCTRL_MT7981=y ++CONFIG_POWER_DOMAIN=y ++CONFIG_MTK_POWER_DOMAIN=y ++CONFIG_DM_REGULATOR=y ++CONFIG_DM_REGULATOR_FIXED=y ++CONFIG_DM_SERIAL=y ++CONFIG_MTK_SERIAL=y ++CONFIG_HEXDUMP=y ++CONFIG_USE_DEFAULT_ENV_FILE=y ++CONFIG_MTD_SPI_NAND=y ++CONFIG_MTK_SPIM=y ++CONFIG_CMD_MTD=y ++CONFIG_CMD_NAND=y ++CONFIG_CMD_NAND_TRIMFFS=y ++CONFIG_LMB_MAX_REGIONS=64 ++CONFIG_USE_IPADDR=y ++CONFIG_IPADDR="192.168.1.1" ++CONFIG_USE_SERVERIP=y ++CONFIG_SERVERIP="192.168.1.254" +--- /dev/null ++++ b/arch/arm/dts/mt7981_jcg_q30-pro.dts +@@ -0,0 +1,179 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Copyright (c) 2022 MediaTek Inc. ++ * Author: Sam Shih ++ */ ++ ++/dts-v1/; ++#include "mt7981.dtsi" ++#include ++#include ++ ++/ { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ model = "JCG Q30 PRO"; ++ compatible = "mediatek,mt7981", "mediatek,mt7981-rfb"; ++ ++ chosen { ++ stdout-path = &uart0; ++ tick-timer = &timer0; ++ }; ++ ++ memory@40000000 { ++ device_type = "memory"; ++ reg = <0x40000000 0x10000000>; ++ }; ++ ++ keys { ++ compatible = "gpio-keys"; ++ ++ factory { ++ label = "reset"; ++ linux,code = ; ++ gpios = <&gpio 1 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ ++ status_red { ++ label = "red:status"; ++ gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ status_blue { ++ label = "blue:status"; ++ gpios = <&gpio 13 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++}; ++ ++&uart0 { ++ mediatek,force-highspeed; ++ status = "okay"; ++}; ++ ++&uart1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_pins>; ++ status = "disabled"; ++}; ++ ++ð { ++ status = "okay"; ++ mediatek,gmac-id = <0>; ++ phy-mode = "2500base-x"; ++ mediatek,switch = "mt7531"; ++ reset-gpios = <&gpio 39 GPIO_ACTIVE_HIGH>; ++ ++ fixed-link { ++ speed = <2500>; ++ full-duplex; ++ }; ++}; ++ ++&pinctrl { ++ spi_flash_pins: spi0-pins-func-1 { ++ mux { ++ function = "flash"; ++ groups = "spi0", "spi0_wp_hold"; ++ }; ++ ++ conf-pu { ++ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; ++ drive-strength = ; ++ bias-pull-up = ; ++ }; ++ ++ conf-pd { ++ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; ++ drive-strength = ; ++ bias-pull-down = ; ++ }; ++ }; ++ ++ spic_pins: spi1-pins-func-1 { ++ mux { ++ function = "spi"; ++ groups = "spi1_1"; ++ }; ++ }; ++ ++ uart1_pins: spi1-pins-func-3 { ++ mux { ++ function = "uart"; ++ groups = "uart1_2"; ++ }; ++ }; ++ ++ pwm_pins: pwm0-pins-func-1 { ++ mux { ++ function = "pwm"; ++ groups = "pwm0_1", "pwm1_0"; ++ }; ++ }; ++}; ++ ++&pwm { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pwm_pins>; ++ status = "okay"; ++}; ++ ++&spi0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi_flash_pins>; ++ status = "okay"; ++ must_tx; ++ enhance_timing; ++ dma_ext; ++ ipm_design; ++ support_quad; ++ tick_dly = <2>; ++ sample_sel = <0>; ++ ++ spi_nand@0 { ++ compatible = "spi-nand"; ++ reg = <0>; ++ spi-max-frequency = <52000000>; ++ ++ partitions { ++ compatible = "fixed-partitions"; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ partition@0 { ++ label = "bl2"; ++ reg = <0x0 0x100000>; ++ }; ++ ++ partition@100000 { ++ label = "orig-env"; ++ reg = <0x100000 0x80000>; ++ }; ++ ++ partition@160000 { ++ label = "factory"; ++ reg = <0x180000 0x200000>; ++ }; ++ ++ partition@380000 { ++ label = "fip"; ++ reg = <0x380000 0x200000>; ++ }; ++ ++ partition@580000 { ++ label = "ubi"; ++ reg = <0x580000 0x7000000>; ++ }; ++ }; ++ }; ++}; ++ ++&watchdog { ++ status = "disabled"; ++}; +--- /dev/null ++++ b/jcg_q30-pro_env +@@ -0,0 +1,57 @@ ++ipaddr=192.168.1.1 ++serverip=192.168.1.254 ++loadaddr=0x46000000 ++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0 ++bootcmd=if pstore check ; then run boot_recovery ; else run boot_ubi ; fi ++bootconf=config-1 ++bootdelay=0 ++bootfile=openwrt-mediatek-filogic-jcg_q30-pro-initramfs-recovery.itb ++bootfile_bl2=openwrt-mediatek-filogic-jcg_q30-pro-preloader.bin ++bootfile_fip=openwrt-mediatek-filogic-jcg_q30-pro-bl31-uboot.fip ++bootfile_upg=openwrt-mediatek-filogic-jcg_q30-pro-squashfs-sysupgrade.itb ++bootled_pwr=blue:status ++bootled_rec=red:status ++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60 ++bootmenu_default=0 ++bootmenu_delay=0 ++bootmenu_title= ( ( ( OpenWrt ) ) ) ++bootmenu_0=Initialize environment.=run _firstboot ++bootmenu_0d=Run default boot command.=run boot_default ++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return ++bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return ++bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return ++bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return ++bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return ++bootmenu_6=Load BL31+U-Boot FIP via TFTP then write to NAND.=run boot_tftp_write_fip ; run bootmenu_confirm_return ++bootmenu_7=Load BL2 preloader via TFTP then write to NAND.=run boot_tftp_write_bl2 ; run bootmenu_confirm_return ++bootmenu_8=Reboot.=reset ++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset ++boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu ++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever ++boot_production=led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off ++boot_recovery=led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off ++boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever ++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done ++boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi ++boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi ++boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf ++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory ++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2 ++part_default=production ++part_recovery=recovery ++reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800 ++mtd_write_fip=mtd erase fip && mtd write fip $loadaddr ++mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr ++ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic 0 || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic 1 || run ubi_format ++ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset ++ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi ++ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs ++ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery ++ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data ++ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic 2 && ubi write $loadaddr fit $filesize ++ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic 3 && ubi write $loadaddr recovery $filesize ++ethaddr_factory=mtd read factory 0x40080000 0xa0000 0x800 && env readmem -b ethaddr 0x4008002a 0x6 ; setenv ethaddr_factory ++_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv ++_firstboot=setenv _firstboot ; run ethaddr_factory ; run _switch_to_menu ; run _init_env ; run boot_first ++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title ++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title $ver"