From: Sujith Date: Mon, 16 Nov 2009 06:10:48 +0000 (+0530) Subject: ath9k: Cleanup bss_info_changed callback X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=c6089ccc22377bcbf055ece6a45b931a02630824;p=openwrt%2Fstaging%2Fblogic.git ath9k: Cleanup bss_info_changed callback * Remove a code chunk dealing with operating mode changes. As noted, all such policy changes are to be done in add_interface. * Remove pointless check for empty BSSID. Also, remove mode checks - mac80211 does all the needed checks. * Handle enabling/disabling beacon transmission properly. * Handle beacon interval changes for AP mode. The original code depended on config_interface() to update the HW TSF. Since that callback has been removed, handle it properly. * Remove unneeded code dealing with key/privacy. * Set the chainmasks to 1x1 for IBSS when the BSSID is set. This was happening uncondionally before. Signed-off-by: Sujith Signed-off-by: John W. Linville --- diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 3c02b977a613..3229c3993568 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -2956,90 +2956,62 @@ static void ath9k_bss_info_changed(struct ieee80211_hw *hw, struct ath_hw *ah = sc->sc_ah; struct ath_common *common = ath9k_hw_common(ah); struct ath_vif *avp = (void *)vif->drv_priv; - u32 rfilt = 0; - int error, i; + int error; mutex_lock(&sc->mutex); - /* - * TODO: Need to decide which hw opmode to use for - * multi-interface cases - * XXX: This belongs into add_interface! - */ - if (vif->type == NL80211_IFTYPE_AP && - ah->opmode != NL80211_IFTYPE_AP) { - ah->opmode = NL80211_IFTYPE_STATION; - ath9k_hw_setopmode(ah); - memcpy(common->curbssid, common->macaddr, ETH_ALEN); + if (changed & BSS_CHANGED_BSSID) { + /* Set BSSID */ + memcpy(common->curbssid, bss_conf->bssid, ETH_ALEN); + memcpy(avp->bssid, bss_conf->bssid, ETH_ALEN); common->curaid = 0; ath9k_hw_write_associd(ah); - /* Request full reset to get hw opmode changed properly */ - sc->sc_flags |= SC_OP_FULL_RESET; - } - if ((changed & BSS_CHANGED_BSSID) && - !is_zero_ether_addr(bss_conf->bssid)) { - switch (vif->type) { - case NL80211_IFTYPE_STATION: - case NL80211_IFTYPE_ADHOC: - case NL80211_IFTYPE_MESH_POINT: - /* Set BSSID */ - memcpy(common->curbssid, bss_conf->bssid, ETH_ALEN); - memcpy(avp->bssid, bss_conf->bssid, ETH_ALEN); - common->curaid = 0; - ath9k_hw_write_associd(ah); + /* Set aggregation protection mode parameters */ + sc->config.ath_aggr_prot = 0; - /* Set aggregation protection mode parameters */ - sc->config.ath_aggr_prot = 0; + /* Only legacy IBSS for now */ + if (vif->type == NL80211_IFTYPE_ADHOC) + ath_update_chainmask(sc, 0); - ath_print(common, ATH_DBG_CONFIG, - "RX filter 0x%x bssid %pM aid 0x%x\n", - rfilt, common->curbssid, common->curaid); + ath_print(common, ATH_DBG_CONFIG, + "BSSID: %pM aid: 0x%x\n", + common->curbssid, common->curaid); - /* need to reconfigure the beacon */ - sc->sc_flags &= ~SC_OP_BEACONS ; + /* need to reconfigure the beacon */ + sc->sc_flags &= ~SC_OP_BEACONS ; + } - break; - default: - break; - } + /* Enable transmission of beacons (AP, IBSS, MESH) */ + if ((changed & BSS_CHANGED_BEACON) || + ((changed & BSS_CHANGED_BEACON_ENABLED) && bss_conf->enable_beacon)) { + ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq); + error = ath_beacon_alloc(aphy, vif); + if (!error) + ath_beacon_config(sc, vif); } - if ((vif->type == NL80211_IFTYPE_ADHOC) || - (vif->type == NL80211_IFTYPE_AP) || - (vif->type == NL80211_IFTYPE_MESH_POINT)) { - if ((changed & BSS_CHANGED_BEACON) || - (changed & BSS_CHANGED_BEACON_ENABLED && - bss_conf->enable_beacon)) { - /* - * Allocate and setup the beacon frame. - * - * Stop any previous beacon DMA. This may be - * necessary, for example, when an ibss merge - * causes reconfiguration; we may be called - * with beacon transmission active. - */ - ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq); + /* Disable transmission of beacons */ + if ((changed & BSS_CHANGED_BEACON_ENABLED) && !bss_conf->enable_beacon) + ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq); + if (changed & BSS_CHANGED_BEACON_INT) { + sc->beacon_interval = bss_conf->beacon_int; + /* + * In case of AP mode, the HW TSF has to be reset + * when the beacon interval changes. + */ + if (vif->type == NL80211_IFTYPE_AP) { + sc->sc_flags |= SC_OP_TSF_RESET; + ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq); error = ath_beacon_alloc(aphy, vif); if (!error) ath_beacon_config(sc, vif); + } else { + ath_beacon_config(sc, vif); } } - /* Check for WLAN_CAPABILITY_PRIVACY ? */ - if ((avp->av_opmode != NL80211_IFTYPE_STATION)) { - for (i = 0; i < IEEE80211_WEP_NKID; i++) - if (ath9k_hw_keyisvalid(sc->sc_ah, (u16)i)) - ath9k_hw_keysetmac(sc->sc_ah, - (u16)i, - common->curbssid); - } - - /* Only legacy IBSS for now */ - if (vif->type == NL80211_IFTYPE_ADHOC) - ath_update_chainmask(sc, 0); - if (changed & BSS_CHANGED_ERP_PREAMBLE) { ath_print(common, ATH_DBG_CONFIG, "BSS Changed PREAMBLE %d\n", bss_conf->use_short_preamble); @@ -3065,18 +3037,6 @@ static void ath9k_bss_info_changed(struct ieee80211_hw *hw, ath9k_bss_assoc_info(sc, vif, bss_conf); } - /* - * The HW TSF has to be reset when the beacon interval changes. - * We set the flag here, and ath_beacon_config_ap() would take this - * into account when it gets called through the subsequent - * config_interface() call - with IFCC_BEACON in the changed field. - */ - - if (changed & BSS_CHANGED_BEACON_INT) { - sc->sc_flags |= SC_OP_TSF_RESET; - sc->beacon_interval = bss_conf->beacon_int; - } - mutex_unlock(&sc->mutex); }