From: Andreas Wiese Date: Wed, 27 May 2020 13:31:30 +0000 (+0200) Subject: ath79: add support for TP-Link RE450 v3 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=c764c512ac18ce9724b3fb0e476831150817c162;p=openwrt%2Fstaging%2Fadrian.git ath79: add support for TP-Link RE450 v3 TP-Link RE450 v3 is a dual band router/range-extender based on Qualcomm/Atheros QCA9563 + QCA9880. This device is nearly identical to RE450 v2 besides a modified flash layout (hence I think force-flashing a RE450v2 image will lead to at least loss of MAC address). Specification: - 775 MHz CPU - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 1x 10/100/1000 Mbps Ethernet (AR8033 PHY) - 7x LED, 4x button- - possible UART header on PCB¹ Flash instruction: Apply factory image in OEM firmware web-gui. ¹ Didn't check to connect as I didn't even manage to connect on RE450v2 (AFAIU it requires disconnecting some resistors, which I was too much of a coward to do). But given the similarities to v2 I think it's the same or very similar procedure (and most likely also the only way to debrick). Signed-off-by: Andreas Wiese [remove dts-v1 and compatible in DTSI] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ath79/dts/qca9563_tplink_re450-v2.dts b/target/linux/ath79/dts/qca9563_tplink_re450-v2.dts index 16bc26c978..4446163a50 100644 --- a/target/linux/ath79/dts/qca9563_tplink_re450-v2.dts +++ b/target/linux/ath79/dts/qca9563_tplink_re450-v2.dts @@ -1,194 +1,47 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT /dts-v1/; -#include -#include - -#include "qca956x.dtsi" +#include "qca9563_tplink_re450.dtsi" / { compatible = "tplink,re450-v2", "qca,qca9563"; model = "TP-Link RE450 v2"; +}; - chosen { - bootargs = "console=ttyS0,115200n8"; +&partitions { + partition@0 { + label = "u-boot"; + reg = <0x000000 0x020000>; + read-only; }; - aliases { - led-boot = &led_power; - led-failsafe = &led_power; - led-running = &led_power; - led-upgrade = &led_power; - mdio-gpio0 = &mdio2; + partition@20000 { + compatible = "tplink,firmware"; + label = "firmware"; + reg = <0x020000 0x5e0000>; }; - leds { - compatible = "gpio-leds"; - - led_power: power { - label = "tp-link:blue:power"; - gpios = <&gpio 1 GPIO_ACTIVE_LOW>; - }; - - wlan2g { - label = "tp-link:blue:wlan2g"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - linux,default-trigger = "phy1tpt"; - }; - - wlan5g { - label = "tp-link:blue:wlan5g"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - linux,default-trigger = "phy0tpt"; - }; - - lan_link { - label = "tp-link:green:lan_link"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - - lan_data { - label = "tp-link:green:lan_data"; - gpios = <&gpio 9 GPIO_ACTIVE_LOW>; - }; - - wps_blue { - label = "tp-link:blue:wps"; - gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; - }; - - wps_red { - label = "tp-link:red:wps"; - gpios = <&gpio 20 GPIO_ACTIVE_HIGH>; - }; + partition@600000 { + label = "partition-table"; + reg = <0x600000 0x010000>; + read-only; }; - keys { - compatible = "gpio-keys"; - - reset { - label = "Reset button"; - linux,code = ; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - }; - - power { - label = "Power button"; - linux,code = ; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - }; - - leds { - label = "LED control button"; - linux,code = ; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - }; - - wps { - label = "WPS button"; - linux,code = ; - gpios = <&gpio 19 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - }; + info: partition@610000 { + label = "info"; + reg = <0x610000 0x020000>; + read-only; }; - mdio2: mdio { - compatible = "virtual,mdio-gpio"; - - gpios = <&gpio 3 GPIO_ACTIVE_HIGH>, /* MDC */ - <&gpio 4 GPIO_ACTIVE_HIGH>; /* MDIO */ - #address-cells = <1>; - #size-cells = <0>; - - phy4: ethernet-phy@4 { - reg = <4>; - device_type = "ethernet-phy"; - reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - }; + partition@630000 { + label = "config"; + reg = <0x630000 0x020000>; + read-only; }; -}; - -&pcie { - status = "okay"; -}; - -&uart { - status = "okay"; -}; - -&gpio { - status = "okay"; -}; - -&spi { - status = "okay"; - - num-cs = <1>; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <25000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x000000 0x020000>; - read-only; - }; - - partition@20000 { - compatible = "tplink,firmware"; - label = "firmware"; - reg = <0x020000 0x5e0000>; - }; - - partition@600000 { - label = "partition-table"; - reg = <0x600000 0x010000>; - read-only; - }; - info: partition@610000 { - label = "info"; - reg = <0x610000 0x020000>; - read-only; - }; - - partition@630000 { - label = "config"; - reg = <0x630000 0x020000>; - read-only; - }; - - art: partition@7f0000 { - label = "art"; - reg = <0x7f0000 0x010000>; - read-only; - }; - }; + art: partition@7f0000 { + label = "art"; + reg = <0x7f0000 0x010000>; + read-only; }; }; - -ð0 { - status = "okay"; - - phy-mode = "sgmii"; - phy-handle = <&phy4>; - - mtd-mac-address = <&info 0x8>; -}; - -&wmac { - status = "okay"; - - mtd-cal-data = <&art 0x1000>; - mtd-mac-address = <&info 0x8>; -}; diff --git a/target/linux/ath79/dts/qca9563_tplink_re450-v3.dts b/target/linux/ath79/dts/qca9563_tplink_re450-v3.dts new file mode 100644 index 0000000000..f85f02428b --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_re450-v3.dts @@ -0,0 +1,53 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "qca9563_tplink_re450.dtsi" + +/ { + compatible = "tplink,re450-v3", "qca,qca9563"; + model = "TP-Link RE450 v3"; +}; + +&partitions { + partition@0 { + label = "u-boot"; + reg = <0x000000 0x020000>; + read-only; + }; + + info: partition@20000 { + label = "info"; + reg = <0x020000 0x002000>; + read-only; + }; + + partition@22000 { + label = "partition-table"; + reg = <0x022000 0x002000>; + read-only; + }; + + partition@24000 { + label = "info2"; + reg = <0x024000 0x00a000>; + read-only; + }; + + partition@2e000 { + label = "config"; + reg = <0x02e000 0x022000>; + read-only; + }; + + partition@50000 { + compatible = "tplink,firmware"; + label = "firmware"; + reg = <0x050000 0x7a0000>; + }; + + art: partition@7f0000 { + label = "art"; + reg = <0x7f0000 0x010000>; + read-only; + }; +}; diff --git a/target/linux/ath79/dts/qca9563_tplink_re450.dtsi b/target/linux/ath79/dts/qca9563_tplink_re450.dtsi new file mode 100644 index 0000000000..4e1195b647 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_re450.dtsi @@ -0,0 +1,154 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include +#include + +#include "qca956x.dtsi" + +/ { + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + mdio-gpio0 = &mdio2; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "tp-link:blue:power"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + label = "tp-link:blue:wlan2g"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wlan5g { + label = "tp-link:blue:wlan5g"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + lan_link { + label = "tp-link:green:lan_link"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + lan_data { + label = "tp-link:green:lan_data"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + + wps_blue { + label = "tp-link:blue:wps"; + gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + }; + + wps_red { + label = "tp-link:red:wps"; + gpios = <&gpio 20 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "Reset button"; + linux,code = ; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + power { + label = "Power button"; + linux,code = ; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + leds { + label = "LED control button"; + linux,code = ; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + wps { + label = "WPS button"; + linux,code = ; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + mdio2: mdio { + compatible = "virtual,mdio-gpio"; + + gpios = <&gpio 3 GPIO_ACTIVE_HIGH>, /* MDC */ + <&gpio 4 GPIO_ACTIVE_HIGH>; /* MDIO */ + #address-cells = <1>; + #size-cells = <0>; + + phy4: ethernet-phy@4 { + reg = <4>; + device_type = "ethernet-phy"; + reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&uart { + status = "okay"; +}; + +&gpio { + status = "okay"; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + }; + }; +}; + +ð0 { + status = "okay"; + + phy-mode = "sgmii"; + phy-handle = <&phy4>; + + mtd-mac-address = <&info 0x8>; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&info 0x8>; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index d4fdb423ab..5521379cea 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -248,7 +248,8 @@ tplink,tl-wr902ac-v1) ;; tplink,re355-v1|\ tplink,re450-v1|\ -tplink,re450-v2) +tplink,re450-v2|\ +tplink,re450-v3) ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx" ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link" ;; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 6fe76817ff..1672f093a7 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -43,6 +43,7 @@ ath79_setup_interfaces() tplink,re355-v1|\ tplink,re450-v1|\ tplink,re450-v2|\ + tplink,re450-v3|\ tplink,tl-wr902ac-v1|\ ubnt,bullet-m-ar7240|\ ubnt,bullet-m-ar7241|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 3ce95905b8..29815a1ada 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -118,7 +118,8 @@ case "$FIRMWARE" in caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -2) ;; - tplink,re450-v2) + tplink,re450-v2|\ + tplink,re450-v3) caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1) ;; diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index 3eedce4f8e..5fb36ca621 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -400,6 +400,18 @@ define Device/tplink_re450-v2 endef TARGET_DEVICES += tplink_re450-v2 +define Device/tplink_re450-v3 + $(Device/tplink-safeloader) + SOC := qca9563 + IMAGE_SIZE := 7808k + DEVICE_MODEL := RE450 + DEVICE_VARIANT := v3 + DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct + TPLINK_BOARD_ID := RE450-V3 + LOADER_TYPE := elf +endef +TARGET_DEVICES += tplink_re450-v3 + define Device/tplink_tl-mr6400-v1 $(Device/tplink-8mlzma) SOC := qca9531 diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index 10178dc714..f0e777124c 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -1728,7 +1728,46 @@ static struct device_info boards[] = { {"user-config", 0x630000, 0x10000}, {"default-config", 0x640000, 0x10000}, {"radio", 0x7f0000, 0x10000}, + {NULL, 0, 0} + }, + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "file-system" + }, + + /** Firmware layout for the RE450 v3 */ + { + .id = "RE450-V3", + .vendor = "", + .support_list = + "SupportList:\r\n" + "{product_name:RE450,product_ver:3.0.0,special_id:00000000}\r\n" + "{product_name:RE450,product_ver:3.0.0,special_id:55530000}\r\n" + "{product_name:RE450,product_ver:3.0.0,special_id:45550000}\r\n" + "{product_name:RE450,product_ver:3.0.0,special_id:4A500000}\r\n" + "{product_name:RE450,product_ver:3.0.0,special_id:43410000}\r\n" + "{product_name:RE450,product_ver:3.0.0,special_id:41550000}\r\n" + "{product_name:RE450,product_ver:3.0.0,special_id:41530000}\r\n" + "{product_name:RE450,product_ver:3.0.0,special_id:4B520000}\r\n" + "{product_name:RE450,product_ver:3.0.0,special_id:42520000}\r\n", + .support_trail = '\x00', + .soft_ver = NULL, + + /* We're using a dynamic kernel/rootfs split here */ + .partitions = { + {"fs-uboot", 0x00000, 0x20000}, + {"default-mac", 0x20000, 0x00020}, + {"pin", 0x20020, 0x00020}, + {"product-info", 0x21000, 0x01000}, + {"partition-table", 0x22000, 0x02000}, + {"soft-version", 0x24000, 0x01000}, + {"support-list", 0x25000, 0x01000}, + {"profile", 0x26000, 0x08000}, + {"user-config", 0x2e000, 0x10000}, + {"default-config", 0x3e000, 0x10000}, + {"config-info", 0x4e000, 0x00400}, + {"firmware", 0x50000, 0x7a0000}, + {"radio", 0x7f0000, 0x10000}, {NULL, 0, 0} },