From: Makoto Takeuchi Date: Wed, 24 May 2017 15:37:24 +0000 (+0100) Subject: kirkwood: add support for Cisco ON100 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=ca27b3d370353ff57719718a1964c6b4f10b11a4;p=openwrt%2Fstaging%2Fblogic.git kirkwood: add support for Cisco ON100 The Cisco ON100 device is a Kirkwood based router: SoC: Marvell 88F6282 1600Mhz SDRAM memory: 512MB DDR3 1333Mhz Gigabit ethernet: 2x Marvell 88E1310 (over RGMII) Flash memory: 512MB 2 bi-colour status LEDs (green/red) 1 Reset button 1 USB 2.0 port (on back) 1 SDIO slot (on back) This commit adds a target profile of "Cisco Systems ON100" under the target system "Marvell Kirkwood". Flashing can be performed over tftp, once "dhcp" has been issued: tftpboot ${loadaddr} lede-kirkwood-on100-squashfs-factory.bin nand erase 0x0c0000 ${filesize} nand write ${loadaddr} 0x0c0000 ${filesize} Once flashed, set environment variables to boot: setenv bootcmd nand read \${loadaddr} 0x0c0000 0x540000\; setenv bootargs \; bootm saveenv Signed-off-by: Makoto Takeuchi --- diff --git a/target/linux/kirkwood/base-files/etc/board.d/02_network b/target/linux/kirkwood/base-files/etc/board.d/02_network index 35d735f9dbf4..19f0292b294f 100755 --- a/target/linux/kirkwood/base-files/etc/board.d/02_network +++ b/target/linux/kirkwood/base-files/etc/board.d/02_network @@ -35,6 +35,9 @@ case "$board" in ucidef_set_interface_lan "eth0" "dhcp" ucidef_set_interface_macaddr "lan" $( mtd_get_mac_ascii uboot_env ethaddr ) ;; +"on100") + ucidef_set_interface_lan "eth0 eth1" + ;; *) ucidef_set_interface_lan "eth0" ;; diff --git a/target/linux/kirkwood/base-files/etc/diag.sh b/target/linux/kirkwood/base-files/etc/diag.sh index 1c4632d6136a..64650850d60e 100755 --- a/target/linux/kirkwood/base-files/etc/diag.sh +++ b/target/linux/kirkwood/base-files/etc/diag.sh @@ -23,6 +23,9 @@ get_status_led() { nsa310b) status_led="nsa310:green:sys" ;; + on100) + status_led="on100:green:health" + ;; esac } diff --git a/target/linux/kirkwood/base-files/lib/kirkwood.sh b/target/linux/kirkwood/base-files/lib/kirkwood.sh index 2c7d7baf4b15..dbf345617229 100755 --- a/target/linux/kirkwood/base-files/lib/kirkwood.sh +++ b/target/linux/kirkwood/base-files/lib/kirkwood.sh @@ -33,6 +33,10 @@ kirkwood_board_detect() { name="ib62x0" ;; + "Cisco Systems ON100") + name="on100" + ;; + "Cloud Engines Pogoplug E02") name="pogo_e02" ;; diff --git a/target/linux/kirkwood/image/Makefile b/target/linux/kirkwood/image/Makefile index 141505e002b7..fc21aa465707 100644 --- a/target/linux/kirkwood/image/Makefile +++ b/target/linux/kirkwood/image/Makefile @@ -11,7 +11,7 @@ include $(TOPDIR)/rules.mk include $(INCLUDE_DIR)/image.mk KERNEL_LOADADDR:=0x8000 -TARGET_DEVICES = linksys-audi linksys-viper dockstar goflexnet goflexhome iconnect pogo_e02 ib62x0 nsa310b nsa325 +TARGET_DEVICES = linksys-audi linksys-viper dockstar goflexnet goflexhome iconnect pogo_e02 ib62x0 nsa310b nsa325 on100 UBI_OPTS := -m 2048 -p 128KiB -s 512 UBIFS_OPTS := -m 2048 -e 126KiB -c 4096 @@ -94,6 +94,17 @@ $(Device/dockstar) DEVICE_PACKAGES := kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3 endef +define Device/on100 + DEVICE_TITLE := Cisco Systems ON100 + DEVICE_DTS := kirkwood-on100 +# DEVICE_PACKAGES := kmod-mvsdio kmod-usb-storage kmod-i2c-core kmod-i2c-mv64xxx kmod-ata-core kmod-btmrvl kmod-btmrvl-sdio kmod-libertas kmod-libertas-sdio + DEVICE_PACKAGES := kmod-i2c-mv64xxx + KERNEL_SIZE := 5376k + IMAGES += factory.bin + IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi + UBINIZE_OPTS := -E 5 +endef + define Device/pogo_e02 $(Device/dockstar) DEVICE_TITLE := Cloud Engines Pogoplug E02 diff --git a/target/linux/kirkwood/patches-4.4/195-on100.patch b/target/linux/kirkwood/patches-4.4/195-on100.patch new file mode 100644 index 000000000000..8c66f2d17372 --- /dev/null +++ b/target/linux/kirkwood/patches-4.4/195-on100.patch @@ -0,0 +1,173 @@ +--- /dev/null ++++ b/arch/arm/boot/dts/kirkwood-on100.dts +@@ -0,0 +1,160 @@ ++/dts-v1/; ++ ++#include "kirkwood.dtsi" ++#include "kirkwood-6282.dtsi" ++ ++/ { ++ model = "Cisco Systems ON100"; ++ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood"; ++ ++ memory { ++ device_type = "memory"; ++ reg = <0x00000000 0x20000000>; ++ }; ++ ++ aliases { ++ serial0 = &uart0; ++ }; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200n8 earlyprintk"; ++ stdout-path = "serial0:115200n8"; ++ }; ++ ++ gpio_keys { ++ compatible = "gpio-keys"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-0 = <&pmx_btn_reset>; ++ pinctrl-names = "default"; ++ ++ button@1 { ++ label = "Reset Button"; ++ linux,code = ; ++ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ gpio-leds { ++ compatible = "gpio-leds"; ++ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >; ++ pinctrl-names = "default"; ++ ++ health-g { ++ label = "on100:green:health"; ++ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; ++ }; ++ ++ health-r { ++ label = "on100:red:health"; ++ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; ++ }; ++ ++ health2-g { ++ label = "on100:green:health2"; ++ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; ++ }; ++ ++ health2-r { ++ label = "on100:red:health2"; ++ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++}; ++ ++ð0 { ++ status = "okay"; ++ ++ ethernet0-port@0 { ++ phy-handle = <ðphy0>; ++ phy-connection-type = "rgmii-id"; ++ }; ++}; ++ ++ð1 { ++ status = "okay"; ++ ++ ethernet1-port@0 { ++ phy-handle = <ðphy1>; ++ phy-connection-type = "rgmii-id"; ++ }; ++}; ++ ++&mdio { ++ status = "okay"; ++ ++ ethphy0: ethernet-phy@0 { ++ /* Marvell 88E1121R */ ++ compatible = "ethernet-phy-id0141.0cb0", ++ "ethernet-phy-ieee802.3-c22"; ++ reg = <0>; ++ }; ++ ++ ethphy1: ethernet-phy@1 { ++ /* Marvell 88E1121R */ ++ compatible = "ethernet-phy-id0141.0cb0", ++ "ethernet-phy-ieee802.3-c22"; ++ reg = <1>; ++ }; ++}; ++ ++&nand { ++ status = "okay"; ++ ++ partition@0 { ++ label = "u-boot"; ++ reg = <0x00000000 0x000a0000>; ++ read-only; ++ }; ++ ++ partition@a0000 { ++ label = "u-boot environment"; ++ reg = <0x000a0000 0x00020000>; ++ read-only; ++ }; ++ ++ partition@c0000 { ++ label = "kernel"; ++ reg = <0x000c0000 0x00540000>; ++ }; ++ ++ partition@600000 { ++ label = "ubi"; ++ reg = <0x00600000 0x1fa00000>; ++ }; ++}; ++ ++&pinctrl { ++ pmx_led_health_r: pmx-led-health-r { ++ marvell,pins = "mpp45"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_health_g: pmx-led-health-g { ++ marvell,pins = "mpp44"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_health2_r: pmx-led-health2-r { ++ marvell,pins = "mpp47"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_health2_g: pmx-led-health2-g { ++ marvell,pins = "mpp46"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_btn_reset: pmx-led-reset { ++ marvell,pins = "mpp31"; ++ marvell,function = "gpio"; ++ }; ++}; ++ ++&sdio { ++ status = "okay"; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -206,6 +206,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ + kirkwood-nsa310b.dtb \ + kirkwood-nsa310s.dtb \ + kirkwood-nsa325.dtb \ ++ kirkwood-on100.dtb \ + kirkwood-openblocks_a6.dtb \ + kirkwood-openblocks_a7.dtb \ + kirkwood-openrd-base.dtb \