From: Andrew Cameron Date: Wed, 26 Jun 2019 21:40:54 +0000 (-0500) Subject: ath79: add support for TP-Link CPE510-v2/v3 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=cad4132e003cecc386d791d552ddba42c182c216;p=openwrt%2Fstaging%2Fxback.git ath79: add support for TP-Link CPE510-v2/v3 TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, and 4 green LEDs - 1 10/100Mbps Shielded Ethernet Port (Passive PoE in) - Built-in 13dBi 2x2 dual-polarized directional MIMO antenna - Adjustable transmission power from 0 to 23dBm/200mw Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron [whitespace fixes] Signed-off-by: Petr Štetiar --- diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds index 238dda18f6..0cb03db4be 100755 --- a/target/linux/ath79/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/base-files/etc/board.d/01_leds @@ -158,6 +158,15 @@ tplink,cpe210-v3) ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "tp-link:green:link3" "wlan0" "60" "100" ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "tp-link:green:link4" "wlan0" "80" "100" ;; +tplink,cpe510-v2|\ +tplink,cpe510-v3) + ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan" "eth0" + ucidef_set_rssimon "wlan0" "200000" "1" + ucidef_set_led_rssi "rssilow" "RSSILOW" "tp-link:green:link1" "wlan0" "1" "100" "0" "13" + ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "tp-link:green:link2" "wlan0" "26" "100" "-25" "13" + ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "tp-link:green:link3" "wlan0" "51" "100" "-50" "13" + ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "tp-link:green:link4" "wlan0" "76" "100" "-75" "13" + ;; tplink,cpe610-v1) ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan" "eth0" ;; diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 2413b1f4bc..1d4cec025a 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -28,6 +28,8 @@ ath79_setup_interfaces() pqi,air-pen|\ tplink,cpe210-v2|\ tplink,cpe210-v3|\ + tplink,cpe510-v2|\ + tplink,cpe510-v3|\ tplink,cpe610-v1|\ tplink,re350k-v1|\ tplink,re355-v1|\ diff --git a/target/linux/ath79/dts/ar9344_tplink_cpe510-v2.dts b/target/linux/ath79/dts/ar9344_tplink_cpe510-v2.dts new file mode 100644 index 0000000000..758d0c02f0 --- /dev/null +++ b/target/linux/ath79/dts/ar9344_tplink_cpe510-v2.dts @@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "ar9344_tplink_cpe510.dtsi" + +/ { + compatible = "tplink,cpe510-v2", "qca,ar9344"; + model = "TP-Link CPE510 v2"; +}; diff --git a/target/linux/ath79/dts/ar9344_tplink_cpe510-v3.dts b/target/linux/ath79/dts/ar9344_tplink_cpe510-v3.dts new file mode 100644 index 0000000000..0909fcfa73 --- /dev/null +++ b/target/linux/ath79/dts/ar9344_tplink_cpe510-v3.dts @@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "ar9344_tplink_cpe510.dtsi" + +/ { + compatible = "tplink,cpe510-v3", "qca,ar9344"; + model = "TP-Link CPE510 v3"; +}; diff --git a/target/linux/ath79/dts/ar9344_tplink_cpe510.dtsi b/target/linux/ath79/dts/ar9344_tplink_cpe510.dtsi new file mode 100644 index 0000000000..f19ef01d49 --- /dev/null +++ b/target/linux/ath79/dts/ar9344_tplink_cpe510.dtsi @@ -0,0 +1,152 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "ar9344.dtsi" + +/ { + aliases { + led-boot = &system; + led-failsafe = &system; + led-running = &system; + led-upgrade = &system; + }; + + leds { + compatible = "gpio-leds"; + + lan { + label = "tp-link:green:lan"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + + link1 { + label = "tp-link:green:link1"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + + link2 { + label = "tp-link:green:link2"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + link3 { + label = "tp-link:green:link3"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + system: link4 { + label = "tp-link:green:link4"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + linux,code = ; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + +}; + +&ref { + clock-frequency = <40000000>; +}; + +&uart { + status = "okay"; +}; + +&spi { + num-cs = <1>; + + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + uboot: partition@0 { + label = "u-boot"; + reg = <0x000000 0x020000>; + read-only; + }; + + partition@20000 { + label = "partition-table"; + reg = <0x020000 0x010000>; + read-only; + }; + + info: partition@30000 { + label = "info"; + reg = <0x030000 0x010000>; + read-only; + }; + + partition@40000 { + label = "firmware"; + reg = <0x040000 0x780000>; + + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x000000 0x200000>; + }; + + partition@200000 { + label = "rootfs"; + reg = <0x200000 0x580000>; + }; + }; + + partition@7c0000 { + label = "config"; + reg = <0x7c0000 0x030000>; + read-only; + }; + + art: partition@7f0000 { + label = "art"; + reg = <0x7f0000 0x010000>; + read-only; + }; + }; + }; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&info 0x08>; +}; + +ð0 { + status = "okay"; + + mtd-mac-address = <&info 0x08>; + + phy-mode = "mii"; + phy-handle = <&swphy4>; +}; + +ð1 { + status = "okay"; + compatible = "syscon", "simple-mfd"; +}; diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index f1424d02ee..312ce78f22 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -159,6 +159,40 @@ define Device/tplink_cpe210-v3 endef TARGET_DEVICES += tplink_cpe210-v3 +define Device/tplink_cpe510-v2 + $(Device/tplink-safeloader) + ATH_SOC := ar9344 + IMAGE_SIZE := 7680k + DEVICE_MODEL := CPE510 + DEVICE_VARIANT := v2 + DEVICE_PACKAGES := rssileds + TPLINK_BOARD_ID := CPE510V2 + LOADER_TYPE := elf + LOADER_FLASH_OFFS := 0x43000 + COMPILE := loader-$(1).elf + COMPILE/loader-$(1).elf := loader-okli-compile + KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 12288 + SUPPORTED_DEVICES += cpe510-v2 +endef +TARGET_DEVICES += tplink_cpe510-v2 + +define Device/tplink_cpe510-v3 + $(Device/tplink-safeloader) + ATH_SOC := ar9344 + IMAGE_SIZE := 7680k + DEVICE_MODEL := CPE510 + DEVICE_VARIANT := v3 + DEVICE_PACKAGES := rssileds + TPLINK_BOARD_ID := CPE510V3 + LOADER_TYPE := elf + LOADER_FLASH_OFFS := 0x43000 + COMPILE := loader-$(1).elf + COMPILE/loader-$(1).elf := loader-okli-compile + KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 12288 + SUPPORTED_DEVICES += cpe510-v3 +endef +TARGET_DEVICES += tplink_cpe510-v3 + define Device/tplink_cpe610-v1 $(Device/tplink-safeloader) ATH_SOC := ar9344 diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index 773e7ed26c..cfd3645950 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -278,6 +278,91 @@ static struct device_info boards[] = { .first_sysupgrade_partition = "os-image", .last_sysupgrade_partition = "support-list", }, + + /** Firmware layout for the CPE510 V2 */ + { + .id = "CPE510V2", + .vendor = "CPE510(TP-LINK|UN|N300-5):2.0\r\n", + .support_list = + "SupportList:\r\n" + "CPE510(TP-LINK|EU|N300-5|00000000):2.0\r\n" + "CPE510(TP-LINK|EU|N300-5|45550000):2.0\r\n" + "CPE510(TP-LINK|EU|N300-5|55530000):2.0\r\n" + "CPE510(TP-LINK|UN|N300-5|00000000):2.0\r\n" + "CPE510(TP-LINK|UN|N300-5|45550000):2.0\r\n" + "CPE510(TP-LINK|UN|N300-5|55530000):2.0\r\n" + "CPE510(TP-LINK|US|N300-5|00000000):2.0\r\n" + "CPE510(TP-LINK|US|N300-5|45550000):2.0\r\n" + "CPE510(TP-LINK|US|N300-5|55530000):2.0\r\n" + "CPE510(TP-LINK|UN|N300-5):2.0\r\n" + "CPE510(TP-LINK|EU|N300-5):2.0\r\n" + "CPE510(TP-LINK|US|N300-5):2.0\r\n", + .support_trail = '\xff', + .soft_ver = NULL, + + .partitions = { + {"fs-uboot", 0x00000, 0x20000}, + {"partition-table", 0x20000, 0x02000}, + {"default-mac", 0x30000, 0x00020}, + {"product-info", 0x31100, 0x00100}, + {"signature", 0x32000, 0x00400}, + {"os-image", 0x40000, 0x200000}, + {"file-system", 0x240000, 0x570000}, + {"soft-version", 0x7b0000, 0x00100}, + {"support-list", 0x7b1000, 0x00400}, + {"user-config", 0x7c0000, 0x10000}, + {"default-config", 0x7d0000, 0x10000}, + {"log", 0x7e0000, 0x10000}, + {"radio", 0x7f0000, 0x10000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "support-list", + }, + + /** Firmware layout for the CPE510 V3 */ + { + .id = "CPE510V3", + .vendor = "CPE510(TP-LINK|UN|N300-5):3.0\r\n", + .support_list = + "SupportList:\r\n" + "CPE510(TP-LINK|EU|N300-5|00000000):3.0\r\n" + "CPE510(TP-LINK|EU|N300-5|45550000):3.0\r\n" + "CPE510(TP-LINK|EU|N300-5|55530000):3.0\r\n" + "CPE510(TP-LINK|UN|N300-5|00000000):3.0\r\n" + "CPE510(TP-LINK|UN|N300-5|45550000):3.0\r\n" + "CPE510(TP-LINK|UN|N300-5|55530000):3.0\r\n" + "CPE510(TP-LINK|US|N300-5|00000000):3.0\r\n" + "CPE510(TP-LINK|US|N300-5|45550000):3.0\r\n" + "CPE510(TP-LINK|US|N300-5|55530000):3.0\r\n" + "CPE510(TP-LINK|UN|N300-5):3.0\r\n" + "CPE510(TP-LINK|EU|N300-5):3.0\r\n" + "CPE510(TP-LINK|US|N300-5):3.0\r\n", + .support_trail = '\xff', + .soft_ver = NULL, + + .partitions = { + {"fs-uboot", 0x00000, 0x20000}, + {"partition-table", 0x20000, 0x02000}, + {"default-mac", 0x30000, 0x00020}, + {"product-info", 0x31100, 0x00100}, + {"signature", 0x32000, 0x00400}, + {"os-image", 0x40000, 0x200000}, + {"file-system", 0x240000, 0x570000}, + {"soft-version", 0x7b0000, 0x00100}, + {"support-list", 0x7b1000, 0x00400}, + {"user-config", 0x7c0000, 0x10000}, + {"default-config", 0x7d0000, 0x10000}, + {"log", 0x7e0000, 0x10000}, + {"radio", 0x7f0000, 0x10000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "support-list", + }, + /** Firmware layout for the CPE610V1 */ { .id = "CPE610V1",