From: Pawel Dembicki Date: Sat, 2 May 2020 13:33:14 +0000 (+0200) Subject: kirkwood: add support for Zyxel NSA310S X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=d2c3131b3fcc55d9c26abdb7cd3c32d3827c10ed;p=openwrt%2Fstaging%2F981213.git kirkwood: add support for Zyxel NSA310S Zyxel NSA310S is a NAS based on Marvell kirkwood SoC. Specification: - Processor Marvell 88F6702 1 GHz - 256MB RAM - 128MB NAND - 1x GBE LAN port (PHY: Marvell 88E1318) - 2x USB 2.0 - 1x SATA - 3x button - 7x leds - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC) Known issues: - no kernel module for RTC. [*] - buzzer (connected to MPP43) need to be drived by 1kHz signal - no kernel module for internal MCU connected via I2C[**] [*] Karoly Pocsi made simple, unofficial driver for HT1382. It can be found here: https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/ [**] Karoly Pocsi found how CPU talk with MCU: It is possible to query the MCU-controlled fan speed and temperature: i2cget -y 0x0 0x0a 0x07 i2cget -y 0x0 0x0a 0x08 The first value (0x07) is the temperature in ° C, the second (0x08) is the time in milliseconds to complete one fan revolution (rpm = 60,000 / value). Info translated from: https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/ Installation: TFTP: 1. Run serial console and go to u-boot. 2. Copy u-boot via tftp and write to NAND: => mw 0x0800000 0xffff 0x100000 => nand erase 0x0 100000 => setenv ipaddr 192.168.1.2 => setenv serverip 192.168.1.4 => tftp 0x0800000 nsa310s-u-boot.kwb => nand write 0x0800000 0x0 0x100000 => reset 3. Run new u-Boot, repair bootcmd and restore MAC address from sticker => setenv ethaddr AA:BB:CC:DD:EE:FF => saveenv 4. Copy and run initramfs image => setenv ipaddr 192.168.1.2 => setenv serverip 192.168.1.4 => tftpboot zyxel_nsa310s-initramfs-uImage => bootm 0x800000 5. Download sysupgrade image and perform sysupgrade USB: 1. Prepare usb fat32 drive with u-boot.kwb and initramfs image. Stick it to USB 2.0 port. 2. Run serial console and go to u-boot. 3. Copy u-boot from usb and write to NAND: => mw 0x0800000 0xffff 0x100000 => nand erase 0x0 100000 => usb start => fatload usb 0 0x0800000 u-boot.kwb => nand write 0x0800000 0x0 0x100000 => reset 4. Run new u-Boot, repair bootcmd and restore MAC address from sticker => setenv ethaddr AA:BB:CC:DD:EE:FF => saveenv 5. Copy and run initramfs image: => usb start => fatload usb 0 0x0800000 initramfs-uImage => bootm 0x800000 6. Download sysupgrade image and perform sysupgrade. Based on work ThBexx DTS based on dropped support in 0ebdf0c. Tested-by: Lech Perczak Reviewed-by: Lech Perczak Signed-off-by: Pawel Dembicki [NSA310s -> NSA310S in DEVICE_MODEL] Signed-off-by: Petr Štetiar --- diff --git a/package/boot/uboot-envtools/files/kirkwood b/package/boot/uboot-envtools/files/kirkwood index b5f7ddccb7..5e87dd1d62 100644 --- a/package/boot/uboot-envtools/files/kirkwood +++ b/package/boot/uboot-envtools/files/kirkwood @@ -20,6 +20,7 @@ linksys,viper|\ raidsonic,ib-nas62x0|\ seagate,dockstar|\ zyxel,nsa310b|\ +zyxel,nsa310s|\ zyxel,nsa325) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" ;; diff --git a/target/linux/kirkwood/base-files/etc/board.d/02_network b/target/linux/kirkwood/base-files/etc/board.d/02_network index df01b0bb1b..a86c57117d 100755 --- a/target/linux/kirkwood/base-files/etc/board.d/02_network +++ b/target/linux/kirkwood/base-files/etc/board.d/02_network @@ -21,7 +21,8 @@ case "$board" in "raidsonic,ib-nas62x0"|\ "seagate,dockstar"|\ "seagate,goflexhome"|\ -"seagate,goflexnet") +"seagate,goflexnet"|\ +"zyxel,nsa310s") ucidef_set_interface_lan "eth0" "dhcp" ;; "linksys,audi"|\ diff --git a/target/linux/kirkwood/config-5.4 b/target/linux/kirkwood/config-5.4 index 6b68649d74..5529bf89df 100644 --- a/target/linux/kirkwood/config-5.4 +++ b/target/linux/kirkwood/config-5.4 @@ -212,6 +212,7 @@ CONFIG_LZO_DECOMPRESS=y CONFIG_MACH_KIRKWOOD=y CONFIG_MACH_MVEBU_ANY=y CONFIG_MANGLE_BOOTARGS=y +CONFIG_MARVELL_PHY=y CONFIG_MDIO_BUS=y CONFIG_MDIO_DEVICE=y CONFIG_MEMFD_CREATE=y diff --git a/target/linux/kirkwood/files-5.4/arch/arm/boot/dts/kirkwood-nsa310s.dts b/target/linux/kirkwood/files-5.4/arch/arm/boot/dts/kirkwood-nsa310s.dts new file mode 100644 index 0000000000..fe892ffdc2 --- /dev/null +++ b/target/linux/kirkwood/files-5.4/arch/arm/boot/dts/kirkwood-nsa310s.dts @@ -0,0 +1,271 @@ +// SPDX-License-Identifier: GPL-2.0 +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" + +/ { + model = "ZyXEL NSA310S"; + compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood"; + + aliases { + led-boot = &led_green_sys; + led-failsafe = &led_red_sys; + led-running = &led_green_sys; + led-upgrade = &led_red_sys; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + stdout-path = &uart0; + }; + + ocp@f1000000 { + pinctrl: pin-controller@10000 { + pinctrl-names = "default"; + + pmx_usb_power: pmx-usb-power { + marvell,pins = "mpp21"; + marvell,function = "gpio"; + }; + + pmx_pwr_off: pmx-pwr-off { + marvell,pins = "mpp27"; + marvell,function = "gpio"; + }; + + pmx_btn_reset: pmx-btn-reset { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; + + pmx_btn_copy: pmx-btn-copy { + marvell,pins = "mpp25"; + marvell,function = "gpio"; + }; + + pmx_btn_power: pmx-btn-power { + marvell,pins = "mpp26"; + marvell,function = "gpio"; + }; + + pmx_led_usb_green: pmx-led-usb-green { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_led_copy_green: pmx-led-copy-green { + marvell,pins = "mpp22"; + marvell,function = "gpio"; + }; + + pmx_led_copy_red: pmx-led-copy-red { + marvell,pins = "mpp23"; + marvell,function = "gpio"; + }; + + pmx_led_sys_green: pmx-led-sys-green { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_led_sys_red: pmx-led-sys-red { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_led_hdd1_green: pmx-led-hdd1-green { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_led_hdd1_red: pmx-led-hdd1-red { + marvell,pins = "mpp13"; + marvell,function = "gpio"; + }; + + pmx_pwr_sata1: pmx-pwr-sata1 { + marvell,pins = "mpp33"; + marvell,function = "gpio"; + }; + + }; + + i2c@11000 { + status = "okay"; + + rtc@68 { + compatible = "htk,ht1382"; + reg = <0x68>; + }; + }; + + serial@12000 { + status = "okay"; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_usb_power &pmx_pwr_sata1>; + pinctrl-names = "default"; + + usb0_power: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "USB Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>; + }; + + sata1_power: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "SATA1 Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_btn_reset &pmx_btn_copy &pmx_btn_power>; + pinctrl-names = "default"; + + power { + label = "Power Button"; + linux,code = ; + gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>; + }; + + copy { + label = "Copy Button"; + linux,code = ; + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + }; + + reset { + label = "Reset Button"; + linux,code = ; + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_green_sys: green-sys { + label = "nsa310s:green:sys"; + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + + led_red_sys: red-sys { + label = "nsa310s:red:sys"; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + + green-hdd1 { + label = "nsa310s:green:hdd1"; + gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "ata1"; + }; + + red-hdd1 { + label = "nsa310s:red:hdd1"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + }; + + green-usb { + label = "nsa310s:green:usb"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "usb-host"; + }; + + green-copy { + label = "nsa310s:green:copy"; + gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + }; + + red-copy { + label = "nsa310s:red:copy"; + gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio_poweroff { + compatible = "gpio-poweroff"; + pinctrl-0 = <&pmx_pwr_off>; + pinctrl-names = "default"; + gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>; + }; +}; + + +ð0 { + status = "okay"; + + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@1 { + reg = <1>; + phy-mode = "rgmii-id"; + marvell,reg-init = <0x1 0x16 0x0 0x3>, + <0x1 0x10 0x0 0x1017>, + <0x1 0x11 0x0 0x4408>, + <0x1 0x16 0x0 0x0>; + }; +}; + +&nand { + status = "okay"; + chip-delay = <35>; + + partition@0 { + label = "uboot"; + reg = <0x0000000 0x00c0000>; + read-only; + }; + partition@c0000 { + label = "uboot_env"; + reg = <0x00c0000 0x0080000>; + }; + partition@140000 { + label = "ubi"; + reg = <0x0140000 0x7ec0000>; + }; +}; + +&pciec { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&sata { + status = "okay"; + nr-ports = <1>; +}; diff --git a/target/linux/kirkwood/image/Makefile b/target/linux/kirkwood/image/Makefile index 87e0627a63..8cc69195b4 100644 --- a/target/linux/kirkwood/image/Makefile +++ b/target/linux/kirkwood/image/Makefile @@ -148,6 +148,14 @@ define Device/zyxel_nsa310b endef TARGET_DEVICES += zyxel_nsa310b +define Device/zyxel_nsa310s + DEVICE_VENDOR := ZyXEL + DEVICE_MODEL := NSA310S + DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-gpio-button-hotplug + DEVICE_DTS := kirkwood-nsa310s +endef +TARGET_DEVICES += zyxel_nsa310s + define Device/zyxel_nsa325 DEVICE_VENDOR := ZyXEL DEVICE_MODEL := NSA325