From: Sebastian Schaper Date: Tue, 1 Dec 2020 21:34:34 +0000 (+0100) Subject: ath79: add support for D-Link DAP-3662 A1 X-Git-Tag: v21.02.0-rc1~327 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=dc4745da7a3900b5dcd9158d1b83c2cda1d1b9b8;p=openwrt%2Fopenwrt.git ath79: add support for D-Link DAP-3662 A1 Specifications: * QCA9557, 16 MiB Flash, 128 MiB RAM, 802.11n 2T2R * QCA9882, 802.11ac 2T2R * 2x Gigabit LAN (1x 802.11af PoE) * IP68 pole-mountable outdoor case Installation: * Factory Web UI is at 192.168.0.50 login with 'admin' and blank password, flash factory.bin * Recovery Web UI is at 192.168.0.50 connect network cable, hold reset button during power-on and keep it pressed until uploading has started (only required when checksum is ok, e.g. for reverting back to oem firmware), flash factory.bin After flashing factory.bin, additional free space can be reclaimed by flashing sysupgrade.bin, since the factory image requires some padding to be accepted for upgrading via OEM Web UI. Both ethernet ports are set to LAN by default, matching the labelling on the case. However, since both GMAC Interfaces eth0 and eth1 are connected to the switch (QCA8337), the user may create an additional 'wan' interface as desired and override the vlan id settings to map br-lan / wan to either the PoE or non-PoE port, depending on the individual scenario of use. So, the LAN and WAN ports would then be connected to different GMACs, e.g. config interface 'lan' option ifname 'eth0.1' ... config interface 'wan' option ifname 'eth1.2' ... config switch_vlan option device 'switch0' option vlan '1' option ports '1 0t' config switch_vlan option device 'switch0' option vlan '2' option ports '2 6t' Signed-off-by: Sebastian Schaper [add configuration example] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ath79/dts/qca9558_dlink_dap-3662-a1.dts b/target/linux/ath79/dts/qca9558_dlink_dap-3662-a1.dts new file mode 100644 index 0000000000..55ac061a56 --- /dev/null +++ b/target/linux/ath79/dts/qca9558_dlink_dap-3662-a1.dts @@ -0,0 +1,102 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca955x_dlink_dap-2xxx.dtsi" + +/ { + compatible = "dlink,dap-3662-a1", "qca,qca9558"; + model = "D-Link DAP-3662 A1"; + + aliases { + led-boot = &led_power_green; + led-failsafe = &led_power_red; + led-running = &led_power_green; + led-upgrade = &led_power_red; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power_red: power_red { + label = "red:power"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + led_power_green: power_green { + label = "green:power"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + }; +}; + +&partitions { + partition@70000 { + label = "firmware"; + reg = <0x70000 0xef0000>; + compatible = "wrg"; + }; + + partition@f60000 { + label = "dlink"; + reg = <0xf60000 0x90000>; + read-only; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x10000>; + read-only; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + + qca,ar8327-initvals = < + 0x04 0x07600000 /* PORT0_PAD_CTRL */ + 0x0c 0x00080080 /* PORT6_PAD_CTRL */ + 0x7c 0x0000007e /* PORT0_STATUS */ + 0x94 0x0000007e /* PORT6_STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + phy-handle = <&phy0>; + pll-data = <0x56000000 0x00000101 0x00001616>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +ð1 { + status = "okay"; + + pll-data = <0x03000101 0x00000101 0x00001616>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&pcie0 { + status = "okay"; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 4380a380fc..c816a85460 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -204,6 +204,10 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "2:lan" "3:wan" "6@eth1" ;; + dlink,dap-3662-a1) + ucidef_add_switch "switch0" \ + "0@eth0" "1:lan:2" "2:lan:1" "6@eth1" + ;; dlink,dch-g020-a1) ucidef_add_switch "switch0" \ "0@eth0" "1:lan:2" "2:lan:1" @@ -502,7 +506,8 @@ ath79_setup_macs() lan_mac=$(mtd_get_mac_ascii bdcfg "lanmac") label_mac=$lan_mac ;; - dlink,dap-2695-a1) + dlink,dap-2695-a1|\ + dlink,dap-3662-a1) label_mac=$(mtd_get_mac_ascii bdcfg "wlanmac") ;; dlink,dir-825-b1) diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 9a199b4deb..5a44dd94e5 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -56,7 +56,8 @@ case "$FIRMWARE" in ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) -1) ;; dlink,dap-2660-a1|\ - dlink,dap-2695-a1) + dlink,dap-2695-a1|\ + dlink,dap-3662-a1) caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a) ;; diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 5edc2e4a86..ac8b59c538 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -27,7 +27,8 @@ case "$board" in mtd_get_mac_ascii bdcfg "wlanmac" > /sys${DEVPATH}/macaddress ;; dlink,dap-2660-a1|\ - dlink,dap-2680-a1) + dlink,dap-2680-a1|\ + dlink,dap-3662-a1) [ "$PHYNBR" -eq 1 ] && \ mtd_get_mac_ascii bdcfg "wlanmac" > /sys${DEVPATH}/macaddress ;; diff --git a/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum b/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum index b522563f17..92048fd810 100644 --- a/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum +++ b/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum @@ -17,7 +17,8 @@ dlink,dap-2230-a1|\ dlink,dap-2660-a1|\ dlink,dap-2680-a1|\ dlink,dap-2695-a1|\ -dlink,dap-3320-a1) +dlink,dap-3320-a1|\ +dlink,dap-3662-a1) fixwrgg ;; qihoo,c301) diff --git a/target/linux/ath79/generic/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/ath79/generic/base-files/lib/preinit/10_fix_eth_mac.sh index ad7372eb03..c2c7913342 100644 --- a/target/linux/ath79/generic/base-files/lib/preinit/10_fix_eth_mac.sh +++ b/target/linux/ath79/generic/base-files/lib/preinit/10_fix_eth_mac.sh @@ -7,7 +7,8 @@ preinit_set_mac_address() { avm,fritzdvbc) ip link set dev eth0 address $(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)")) ;; - dlink,dap-2695-a1) + dlink,dap-2695-a1|\ + dlink,dap-3662-a1) ip link set dev eth0 address $(mtd_get_mac_ascii bdcfg "lanmac") ip link set dev eth1 address $(mtd_get_mac_ascii bdcfg "wanmac") ;; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index d11cc28146..6eda757445 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -794,6 +794,18 @@ define Device/dlink_dap-3320-a1 endef TARGET_DEVICES += dlink_dap-3320-a1 +define Device/dlink_dap-3662-a1 + $(Device/dlink_dap-2xxx) + SOC := qca9558 + DEVICE_VENDOR := D-Link + DEVICE_MODEL := DAP-3662 + DEVICE_VARIANT := A1 + DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct + IMAGE_SIZE := 15296k + DAP_SIGNATURE := wapac11_dkbs_dap3662 +endef +TARGET_DEVICES += dlink_dap-3662-a1 + define Device/dlink_dch-g020-a1 SOC := qca9531 DEVICE_VENDOR := D-Link