From: Robert Senderek Date: Fri, 16 Feb 2024 13:04:40 +0000 (+0100) Subject: mediatek: filogic: add support for Cudy RE3000 v1 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=e8f75973172749874afa13e4f746acd8cb515de2;p=openwrt%2Fstaging%2Fneocturne.git mediatek: filogic: add support for Cudy RE3000 v1 MT7981B /256MB /16MB SPI (XM25QH128C) AX 2.4Ghz AX 5Ghz 160Mhz wide 1Gbit LAN OEM: root@RE3000:~# ifconfig |grep HWaddr br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 (label) br-wan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 ra0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 ra2 Link encap:Ethernet HWaddr 82:XX:XX:28:XX:X0 rax0 Link encap:Ethernet HWaddr 82:XX:XX:38:XX:X0 rax2 Link encap:Ethernet HWaddr 82:XX:XX:58:XX:X0 OpenWrt root@OpenWrt:/# ifconfig |grep HW br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 phy0-ap0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 phy1-ap0 Link encap:Ethernet HWaddr 82:XX:XX:08:XX:X1 tftp Installation via u-boot: Connect TTL3.3V converter connector is under the radiator Set speed 115200 8 N 1 Interrupt boot process by holding down-arrow key during boot then >> 6. Load image >> 0 - TFTP client (Default) enter IP adresses and initramfs-kernel.bin write to flash via sysupgrade or gui Signed-off-by: Robert Senderek --- diff --git a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface index da9c4e7f40..9f513d20c4 100644 --- a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface +++ b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface @@ -9,6 +9,7 @@ set_preinit_iface() { ip link set eth1 up ifname=eth1 ;; + cudy,re3000-v1|\ ubnt,unifi-6-lr|\ zyxel,nwa50ax-pro) ip link set eth0 up diff --git a/target/linux/mediatek/dts/mt7981b-cudy-re3000-v1.dts b/target/linux/mediatek/dts/mt7981b-cudy-re3000-v1.dts new file mode 100644 index 0000000000..4025e5aaa3 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-cudy-re3000-v1.dts @@ -0,0 +1,221 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include +#include +#include + +#include "mt7981.dtsi" + +/ { + model = "Cudy RE3000 v1"; + compatible = "cudy,re3000-v1", "mediatek,mt7981"; + + aliases { + serial0 = &uart0; + label-mac-device = &gmac1; + led-boot = &led_status; + led-failsafe = &led_status; + led-running = &led_status; + led-upgrade = &led_status; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "wps"; + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status: led@0 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + + led@1 { + label = "red:wifi5"; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + led@2 { + label = "white:wifi2"; + gpios = <&pio 6 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led@3 { + function = LED_FUNCTION_LAN; + color = ; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + led@4 { + function = LED_FUNCTION_WPS; + color = ; + gpios = <&pio 11 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + status = "okay"; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "gmii"; + phy-handle = <&int_gbe_phy>; + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_bdinfo_de00 0>; + }; +}; + +&mdio_bus { + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + }; +}; + +&spi0 { + status = "disabled"; +}; + +&spi2 { + pinctrl-names = "default"; + pinctrl-0 = <&spi2_flash_pins>; + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + + compatible = "jedec,spi-nor"; + reg = <0>; + + spi-max-frequency = <25000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@00000 { + label = "BL2"; + reg = <0x00000 0x40000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x40000 0x10000>; + read-only; + }; + + factory: partition@50000 { + label = "Factory"; + reg = <0x50000 0x10000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + }; + }; + + bdinfo: partition@60000 { + label = "bdinfo"; + reg = <0x60000 0x10000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_bdinfo_de00: macaddr@de00 { + compatible = "mac-base"; + reg = <0xde00 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@70000 { + label = "FIP"; + reg = <0x70000 0x80000>; + read-only; + }; + + partition@f0000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0xf0000 0xf10000>; + }; + }; + }; +}; + +&pio { + spi2_flash_pins: spi2-pins { + mux { + function = "spi"; + groups = "spi2", "spi2_wp_hold"; + }; + + conf-pu { + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; + drive-strength = <8>; + bias-pull-up = <103>; + }; + + conf-pd { + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; + drive-strength = <8>; + bias-pull-down = <103>; + }; + }; +}; + +&wifi { + status = "okay"; + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index 206f7788f5..b3dceb74c4 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -26,6 +26,9 @@ bananapi,bpi-r4) ucidef_set_led_netdev "lan2" "lan2" "mt7530-0:02:green:lan" "lan2" "link tx rx" ucidef_set_led_netdev "lan3" "lan3" "mt7530-0:03:green:lan" "lan3" "link tx rx" ;; +cudy,re3000-v1) + ucidef_set_led_netdev "lan" "lan" "green:lan" "eth0" "link tx rx" + ;; cudy,wr3000-v1) ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" ;; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index c899be1b98..dbda950cc5 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -70,6 +70,7 @@ mediatek_setup_interfaces() mercusys,mr90x-v1) ucidef_set_interfaces_lan_wan "lan0 lan1 lan2" eth1 ;; + cudy,re3000-v1|\ netgear,wax220|\ ubnt,unifi-6-plus|\ zyxel,nwa50ax-pro) diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 1f00e9b285..ebee1b931f 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -61,6 +61,11 @@ case "$board" in addr=$(mtd_get_mac_binary "Factory" 0x8000) [ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress ;; + cudy,re3000-v1) + addr=$(mtd_get_mac_binary bdinfo 0xde00) + [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress + [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress + ;; cudy,wr3000-v1) addr=$(mtd_get_mac_binary bdinfo 0xde00) # Originally, phy0 is phy1 mac with LA bit set. However, this would conflict diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index e0c64ab85f..526de08161 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -113,6 +113,7 @@ platform_do_upgrade() { ;; esac ;; + cudy,re3000-v1|\ cudy,wr3000-v1|\ yuncore,ax835) default_do_upgrade "$1" diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 7d57957b6c..b1c043bef2 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -453,6 +453,25 @@ define Device/confiabits_mt7981 endef TARGET_DEVICES += confiabits_mt7981 +define Device/cudy_re3000-v1 + DEVICE_VENDOR := Cudy + DEVICE_MODEL := RE3000 + DEVICE_VARIANT := v1 + DEVICE_DTS := mt7981b-cudy-re3000-v1 + DEVICE_DTS_DIR := ../dts + DEVICE_DTS_LOADADDR := 0x47000000 + IMAGES := sysupgrade.bin + IMAGE_SIZE := 15424k + SUPPORTED_DEVICES += R36 + KERNEL := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGE/sysupgrade.bin := append-kernel | pad-to 128k | append-rootfs | pad-rootfs | check-size | append-metadata + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware +endef +TARGET_DEVICES += cudy_re3000-v1 + define Device/cudy_wr3000-v1 DEVICE_VENDOR := Cudy DEVICE_MODEL := WR3000