From: Sander Vanheule <sander@svanheule.net>
Date: Fri, 26 Nov 2021 21:16:47 +0000 (+0100)
Subject: realtek: remove hardcoded sys-led configurations
X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=eae5e55a7938504691f8be27665c6fa3935a01d9;p=openwrt%2Fstaging%2Frobimarko.git

realtek: remove hardcoded sys-led configurations

setup.c unconditionally sets the sys-led mode (blinking rate) to a
permanent high output. This may cause issues when a board expects this
pin to toggle periodically, e.g. when hooked up to an external watchdog.

If the sys-led peripheral is used to control an LED, the mux should be
configured to use the pin as GPIO0, allowing for better control as a
GPIO LED.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
---

diff --git a/target/linux/realtek/files-5.10/arch/mips/rtl838x/setup.c b/target/linux/realtek/files-5.10/arch/mips/rtl838x/setup.c
index 18c477eb0f..e0adbf87e9 100644
--- a/target/linux/realtek/files-5.10/arch/mips/rtl838x/setup.c
+++ b/target/linux/realtek/files-5.10/arch/mips/rtl838x/setup.c
@@ -28,31 +28,6 @@
 
 extern struct rtl83xx_soc_info soc_info;
 
-static void __init rtl838x_setup(void)
-{
-	/* Setup System LED. Bit 15 then allows to toggle it */
-	sw_w32_mask(0, 3 << 16, RTL838X_LED_GLB_CTRL);
-}
-
-static void __init rtl839x_setup(void)
-{
-	/* Setup System LED. Bit 14 of RTL839X_LED_GLB_CTRL then allows to toggle it */
-	sw_w32_mask(0, 3 << 15, RTL839X_LED_GLB_CTRL);
-}
-
-static void __init rtl930x_setup(void)
-{
-	if (soc_info.id == 0x9302)
-		sw_w32_mask(0, 3 << 13, RTL9302_LED_GLB_CTRL);
-	else
-		sw_w32_mask(0, 3 << 13, RTL930X_LED_GLB_CTRL);
-}
-
-static void __init rtl931x_setup(void)
-{
-	sw_w32_mask(0, 3 << 12, RTL931X_LED_GLB_CTRL);
-}
-
 void __init plat_mem_setup(void)
 {
 	void *dtb;
@@ -71,21 +46,6 @@ void __init plat_mem_setup(void)
 	 * parsed resulting in our memory appearing
 	 */
 	__dt_setup_arch(dtb);
-
-	switch (soc_info.family) {
-	case RTL8380_FAMILY_ID:
-		rtl838x_setup();
-		break;
-	case RTL8390_FAMILY_ID:
-		rtl839x_setup();
-		break;
-	case RTL9300_FAMILY_ID:
-		rtl930x_setup();
-		break;
-	case RTL9310_FAMILY_ID:
-		rtl931x_setup();
-		break;
-	}
 }
 
 void __init plat_time_init(void)